MakerBot Replicator Mini Manual de usuario

MakerBot Replicator Mini Teardown Guide

MakerBot

Tools Needed:

1.3mm Hex Driver

T10 - T20 Torx Driver

Phillips Screw Driver

2.0mm Hex Driver

1.5mm Hex Driver

2.5mm Hex Driver

1 Pair of thin Tweezers

Small Container for Screws

Small Wire Cutters

•

MakerBot Replicator

MakerBot

Step 1 - Remove the Door,

Windows and Filament Guide

Step 3 - Remove the Z-Stage

To remove the Door, pull from top

downward and away from the

Minis body.

Remove four (4) button head Torx

To remove side Windows, from the

inside of the printer, apply pressure

to pop out of the slot.

To remove the Filament Guide

Tube, pull upward.

Unplug the z-wire from the

Motor Wire Harness connected

to the Z-stage Motor.

Remove four (4) button head

Torx bolts by using a T20 driver

located in the back of the Inside

Base

Unclip the black clips on the

outer Back Panel by pushing

inward (using a 2.0mm hex

driver can help assist).

Lean the Z-stage Assembly

forward and pull up to remove.

•

MakerBot Replicator

MakerBot

Step 2 - Removing the Floor

Plate

Step 4 - Remove the Power

Supply

Manually rotate the threaded

z-axis threaded rod clockwise to

raise the Build Plate Holder half

way from the Floor Plate. Pull

the Build Plate forward to remove

from the Build Plate Holder.

Remove three (3) button head

Torx bolts from the rear left side of

the Mini.

Disconnect the twenty-pin

connector from the Brooklyn PCB.

Unclip connector from plastic

clips.

Pull Power Supply toward you to

remove it out of the slot.

Remove the three (3) button head

Torx bolts by using a T20 driver.

Lift up the Floor Plate from the

printer to remove.

•

MakerBot Replicator Mini

MakerBot

Step 5 - Remove the Housing

(optional)

Remove the following Screws:

two (2) button head Torx bolts by

using a T20 driver from the front

left and middle of the Inside Base.

eight (8) ﬂathead bolts using a

2.5mm hex driver from the edges

of the Back Panel

one (1) tension bolt by using a

2.5mm hex driver from the Back

Panel.

three (3) button head Torx bolts

by using a T20 driver from the

Side Panels via the inside of the

printer.

two (2) button head Torx bolts by

using a T20 driver from the front

left and middle of the Inside Base.

one (1) lock washer nut and the

ground wire using a 7mm nut

drivert

four (4) button head Torx bolts by

using a T15 driver located on the

upper Inside Panels.

Unplug the Camera Wire at the

bottom of the Base from the

Queens PCB.

Remove the Gantry Belts from the

Gantry Pulley.

Loosen two (2) button head bolts

located on the left Gantry Motor

Mount (frame side).

Unplug Ribbon Cable at the

bottom of the base from the

Queens PCB.

•

Step 6 - Remove the Brooklyn

PCB

Remove the FFC from the

Brooklyn PCB.

Unplug the Motor Wire Harness

from the Brooklyn PCB.

Unplug the 10-pin Ribbon Cable

from the Brooklyn PCB.

Unplug the Wi-Fi Antenna from

the Brooklyn PCB.

Unplug 20-pin Power Supply

Cable.

Lift up the Brooklyn PCB to

remove.

•

MakerBot Replicator Mini

MakerBot

Step 5 - Remove the Housing

continued

Remove the two (2) Torx bolts

using a T10 driver located on the

Extruder Carriage Assembly.

Pull the rear panel of the Housing

Assembly upwards to remove

(using a small driver wedged

between the Back Panel and

Frame allows easier removal).

•

Tabla de contenidos

Otros manuales de Impresora 3D de MakerBot

MakerBot

MakerBot Replicator Z18 Manual de usuario

MakerBot

MakerBot Replicator 2 Manual de usuario

MakerBot

MakerBot Replicator 2X Guía

MakerBot

MakerBot Labs Experimental Extruder Manual de usuario

MakerBot

MakerBot Replicator+ Manual de usuario

MakerBot

MakerBot Replicator Manual de usuario

MakerBot

MakerBot Replicator+ Guía

MakerBot

MakerBot Replicator Z18 Manual de usuario

MakerBot

MakerBot Smart Extruder+ Manual de usuario

MakerBot

MakerBot Replicator 2 Manual de usuario

MakerBot

MakerBot Replicator Z18 Manual de usuario

MakerBot

MakerBot Sketch Manual de usuario

MakerBot

MakerBot Replicator 2X Manual de usuario

MakerBot

MakerBot Replicator Mini Compact Manual de usuario

MakerBot

MakerBot METHOD Manual de usuario

MakerBot

MakerBot Replicator 2 Manual de usuario

MakerBot

MakerBot Replicator 2X Manual de usuario

MakerBot

MakerBot Thing-O-Matic Manual de usuario

MakerBot

MakerBot Replicator 2X Manual de lista de piezas

MakerBot

MakerBot Replicator+ Manual de usuario

MakerBot

MakerBot Replicator 2 Extruder Guía de instalación y uso

MakerBot

MakerBot Replicator 2X Manual de usuario

MakerBot

MakerBot Replicator 2 Manual de usuario

MakerBot

MakerBot Replicator 2X Guía

Manuales populares de Impresora 3D de otras marcas

Ultimaker

Ultimaker S5 Material Station Manual de usuario

EcubMaker

EcubMaker TOYDIY Manual de usuario

AnyCubic

AnyCubic Kossel Plus Manual de usuario

ReDeTec

ReDeTec ProtoCycler Manual de usuario

Kywoo3D

Kywoo3D Tycoon IDEX Manual de usuario

CraftBot

CraftBot PLUS PRO Manual de usuario

3DGence

3DGence INDUSTRY F340 Manual de usuario

HP Jet Fusion 4200 Instrucciones de funcionamiento

Rokit

Rokit AEP Series Manual de usuario

AnkerMake

AnkerMake M5 Manual de usuario

DIYElectronics

DIYElectronics PRUSA I3 Instrucciones de montaje

Ackuretta

Ackuretta FreeShape 120 Manual de usuario

LONGER

LONGER LK5Pro Manual de usuario

Stratasys

Stratasys J850 Manual de usuario

Stratasys

Stratasys FDM Vantage Series Manual de usuario

ZYYX

ZYYX Pro II Manual de usuario

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guía del usuario

LONGER

LONGER LK4 Pro Manual de usuario