M2 Antenna Systems 2M5-440XP Manual de usuario

M2 Antenna Systems, Inc. 4402 N. Selland Ave. Fresno, CA 93722

Tel: (559) 432-8873 Fax: (559) 432-3059 Web: www.m2inc.com

Rev.00

Model ........................................2M5-440XP

Frequency Range......................144-148 / 430-450 MHz

*Gain 2M / 440...........................11.14 / 14.14 dBi

Front to back 2M / 440...............15 dB / 25 dB

Feed Impedance........................50 Ohms Unbalanced

VSWR........................................1.3:1

Connectors.................................“N” Female

Power Handling 2M / 440 ..........1.5 kW / 750W

Boom Length / Dia.....................60” / 1”

Maximum Element Length.........40”

Turning Radius:..........................70”

Stacking Distance ......................Call Factory

Mast Size ...................................1-1/2” to 2” Nom.

Wind area / Survival...................1.1 Sq. Ft. / 100 MPH

Weight / Ship Wt. .......................5.5 Lbs. / 7 Lbs.

M2 Antenna Systems, Inc.

Model No: 2M5-440XP

SPECIFICATIONS:

*Subtract 2.14 from dBi for dBd

FEATURES:

The 2M5-440XP is ideal for linking repeaters and remote bases utilizing both 2 meters and 440 MHz. Elements

are cross polarized to avoid the severe performance compromises on 440 MHz common to other dual band antennas that

have all elements in the same polarity. The XP also works well on the OSCAR frequencies and is handy wherever dual

band capability and compact size are required. Recently, with PACKET users finding horizontal polarization better on 2

meters, it has become even more useful.

Construction is designed for long term mechanical and electrical integrity. The heart of this antenna is the CNC-

machined Driven Element Block. Connectors are O-ring sealed and the internal connections are encapsulated in a space-

age silicone gel with nearly 4 times the dielectric strength of air. Balun connectors are triple sealed and nut-sealed at the

block connectors. Elements are 3/16” 6061-T6 aluminum rod, centered through the boom on UV stabilized insulator

buttons. All hardware except U-bolts is stainless steel (S.S. nuts and lockwashers are supplied for them, too).

2M5-440XP DIMENSION SHEET

2M5-440XP ASSEMBLY MANUAL

TOOL REQUIRED FOR ASSEMBLY: Screwdriver, 11/32 nut driver or wrench, 7/16” and 1/2” end

wrenches, pliers, measuring tape.

1. Assemble the boom sections using the DIMENSION SHEET as a guide. Use 8-32 X 1-1/4 screws

and locknuts to join sections. Sections may be swaged to each other or use 7/8” internal splice

sections.

ASSEMBLING THE 440 MHz ELEMENTS

2. Lay out the elements by length and position as shown the DIMENSION sheet. Start with the

reflector (longest) element. Balance it on your finger to find rough center and push on a black

button insulator to about 1/2” off center. Push the element through the holes 1/2" from the rear of

the boom and install the second button, snugging it up into boom. DO NOT BOTHER CENTERING

the element at this time and DO NOT INSTALL the stainless steel internal locking “keepers” yet. It

is easier to do it after all the horizontal elements are installed in the boom.

3. Install the 3/16” rod DRIVEN ELEMENT as you did the reflector. Then continue with the installation

of the DIRECTORS.

4. Now begin centering the elements. Use a tape measure to EQUALIZE the amount the element

sticking out on each side of the boom. Once you have all the elements centered, sight down the

element tips from the rear comparing each side. Look for any obvious discrepancies and correct if

found.

5. Begin installing the stainless “keepers.” Use thumb and index finger to hold a keeper over end of

the 3/8 x 3” push tube (keeper dished into tube). Hold the element firmly and start the keeper onto

the rod by applying pressure with the push tube. Push the keeper until up tight against the button

insulator (Locking pliers, lightly clamped up against opposite button insulator will help maintain

center reference and keep you from pushing the first keeper too far). Repeat for the opposite side.

Continue installing keepers until all elements are locked in place.

2M5-440XP ASSEMBLY MANUAL

6. Mount the 440 MHz DRIVEN ELEMENT BLOCK / ROD ASSEMBLY to the TOP of the boom using a single 8-

32 X 1-1/4" screw and lockwasher. Orient the block with the two balun connectors facing to front, “N”

connector to rear. Reverse for center mounted antenna.

7. Install the 8-32 x 1/4” set screws (internal Allen head - tool supplied) into the SHORTING BARS. Slide the bars

onto the 1/8” Driven Element Block Rods and the 3/16” Driven Element Rods. Position the inner edge of each

Shorting Bar 4-3/8” from the outer edge of the Driven Element Block (see Dimension Sheet). Align the bars

with each other and tighten the set screws.

ASSEMBLING THE 2 METER ELEMENTS

8. Repeat steps #2 through #5 for the 2 meter elements, using the Dimension Sheet as your guide to lengths and

spacing.

9. Mount the 2 Meter Driven Element Block to the left hand side of the boom with the two Balun connectors

oriented to the FRONT, “N” connector to rear. Reverse for center mounted antenna. Secure with 8-32 x 1-1/4”

screw and lockwasher. Install the Shorting Bars as in step #7.

10. Before installing the Baluns, thread 3/8” SEAL NUTS fully onto all connectors, with the black Neoprene face of

the nuts facing out. Attach Baluns to the Driven Element Blocks as shown on the Dimension Sheet. Tighten

the connectors gently using a 7/16" end wrench. Once the connectors are tight, back the Seal Nuts out and

finger-tighten firmly up against the face of the connectors (or tighten gently with 1/2” end wrench). A lot of

torque is unnecessary and will damage seal. Depending on mounting options, a balun may loop around other

elements. This is normal. Form balun coax until it is close to the boom and secure with a nylon cable tie. Also

secure the other balun. Ties should be snug but not crushing or kinking the coax.

REAR MOUNTING

11. The boom to mast plate is mounted at the rear of boom using two 1" U-bolts and the stainless nuts and lock

washers provided. Rotate to desired polarity. DO NOT OVER TIGHTEN. 2” U-bolts are provided for mounting

the antenna to your mast, tower leg, or crossboom.

CENTER MOUNTING

12. Find the balance point and mount the boom to mast plate with the 1” U-bolts. Since one set of elements will be

in the plane of the mast, a non-conductive mast of fiberglass or equivalent is strongly recommended. 2” U-

bolts are provided for mounting the antenna to your mast, tower leg, or crossboom.

13. Use good quality coax and “N” connector for your feedlines. Secure feed coax near connectors with cable ties

to provide stress relief. Then route tight against boom (AVOID TOUCHING THE ELEMENTS WITH THE

FEEDLINES and secure again with ties or black electrical tape at exit point.

THIS COMPLETES THE ANTENNA ASSEMBLY.

M2ANTENNA SYSTEMS, INC.

4402 N. Selland Ave.

Fresno, CA 93722

(559) 432-8873 FAX: 432-3059

www.m2inc.com Email: [email protected]

DESCRIPTION QTY

BOOM SECTION #1, 1 X .058 X 60” SOE............... 1

BOOM SECTION #2, 1 X .058 X 11-1/2” STR......... 1

DRIVEN ELEMENT BLOCK, 2 METER................... 1

DRIVEN ELEMENT BLOCK, 440 MHz.................... 1

BALUN, RG-6 146 MHz, 33”.................................... 1

BALUN, RG-6 440 MHz, 11”.................................... 1

3/16” ROD ELEMENTS, 2 METER.......................... 5

3/16” ROD ELEMENTS, 440 MHz........................... 10

BOOM-TO-MAST PLATE, 3/16 X 3 X 4” ................. 1

U-BOLT AND CRADLE, 2” ...................................... 2

U-BOLT AND CRADLE, 1” ...................................... 2

ASSEMBLY MANUAL.............................................. 1

IN HARDWARE BAG:

SHORTING BAR, UHF 1/8” HOLE .......................... 2

SHORTING BAR, VHF 1/4” HOLE........................... 2

BUTTON INSULATOR............................................. 30

KEEPER, SS............................................................ 30

NUT, 5/16-18 SS...................................................... 4

LOCKWASHER, 5/16 SS......................................... 4

NUT, 1/4-20 SS........................................................ 4

LOCKWASHERS, 1/4 SS ........................................ 4

SCREW, 8-32 X 1-1/4 SS........................................ 4

LOCKNUT, 8-32 SS................................................. 2

LOCKWASHER, #8 SS............................................ 2

SET SCREW, 8-32 X 1/4 SS ................................... 8

CABLE TIE, NYLON ............................................... 5

SEAL NUTS............................................................. 4

ALLEN HEAD WRENCH, 5/64” ............................... 1

PUSH TUBE, 3/8 X 3”.............................................. 1

M2ANTENNA SYSTEMS, INC.

4402 N. Selland Ave.

Fresno, CA 93722

(559) 432-8873 FAX: 432-3059

www.m2inc.com Email: [email protected]

2M5-440XP PARTS & HARDWARE

Tabla de contenidos

Otros manuales de Antena de M2 Antenna Systems

M2 Antenna Systems

M2 Antenna Systems EB-432/RK70CM Manual de usuario

M2 Antenna Systems

M2 Antenna Systems FGSD-2.4DH Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 6M5XHP Manual de usuario

M2 Antenna Systems

M2 Antenna Systems EB-144/RK2M Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 222 HO LOOP Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 902-5 YAGI Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 300XP12 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 40M2C Manual de usuario

M2 Antenna Systems

M2 Antenna Systems SYSTEM SAMPLE 3 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 20M6-125 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 249CP24 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 295XP6 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 2MXP20 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 432-12EME Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 2M8WL Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 500-1000-10 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 7-10-30LP8 UP-KIT Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 80M2L Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 75-5AS Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 222-10EZ Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 80M1L Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 440-18 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 902-14WLC Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 6M7JHVHD Manual de usuario

Manuales populares de Antena de otras marcas

Alfa Network

Alfa Network APA-L01 Manual de usuario

Naval

Naval PR-422CA Manual de usuario

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manual de usuario

TERK Technologies

TERK Technologies TV44 Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manual de usuario

HP J8999A Manual de usuario

MobilSat

MobilSat MSP-S Manual de usuario

Steren

Steren ANT-UHF 13 Manual de usuario

Novatel

Novatel 600-G Manual de operación

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manual de usuario

TRENDnet

TRENDnet TEW-AO12O Manual de usuario

Radio Shack

Radio Shack 15-1837 Manual de usuario

CommScope

CommScope CMAX-OMFX-43M-I53 Manual de usuario

Ramsey Electronics

Ramsey Electronics DAP25 Manual de usuario

COBHAM

COBHAM SAILOR 800 VSAT Manual de uso y cuidado

Trango Systems

Trango Systems AD900-9 Manual de usuario

Steren

Steren ANT-100 Manual de usuario

Proxim

Proxim 5054-PA-23 Manual de usuario