M-system R8-PA4 Manual de usuario

R8-PA4

P. 1 / 4

EM-9739 Rev.1

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

TOTALIZED PULSE INPUT MODULE, 4 points

(NPN / PNP / Voltage pulse input) MODEL R8-PA4

INSTRUCTION MANUAL

BEFORE USE ....

Thank you for choosing M-System. Before use, check the

contents of the package you received as below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■ PACKAGE INCLUDES:

Pulse input module ..................................................... (1)

■MODEL NO.

Conﬁrm that the model number described on the product is

exactly what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

•Theequipmentmustbemountedinsideapanel.

•Theactualinstallationenvironmentssuchaspanelcon-

ﬁgurations, connected devices and connected wires may

affect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure CE conformity.

■GENERAL PRECAUTIONS

•Beforeyouremoveormounttheunit,turnoffthepower

supply and input signal for safety.

•Switches on the side of the module can be set for mainte-

nance only while the power supply is off. Do not access

them while the power is supplied.

■ ENVIRONMENT

•Indooruse

•Whenheavydustormetalparticlesarepresentintheair,

install the unit inside proper housing with sufﬁcient ven-

tilation.

•Donotinstalltheunitwhereitissubjectedtocontinuous

vibration. Do not apply physical impact to the unit.

•Environmentaltemperaturemustbewithin-10to+55°C

(14to131°F)withrelativehumiditywithin30to90%RH

in order to ensure adequate life span and operation.

■WIRING

•Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

•Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■EXCITATION SUPPLY

Power output(input terminal): Ratedcurent 0.1A DC per

channel(ratedcurrent3Aforinternalfuse(slowblowfuse

i2t(A2sec)max.0.31),Total0.4ADC

■AND ....

•Theunitisdesignedtofunctionassoonaspowerissup-

plied,however,awarmupfor10minutesisrequiredfor

satisfying complete performance described in the data

sheet.

INSTALLATION

■HOW TO MOUNT THE MODULE ON DIN RAIL

• I/O Module

Confirm that the locking clamps of the I/O module are set.

Insert the module in parallel to the next one while aligning the grooves of

both modules (A & B in the above figure).

Maintain it perpendicularly to the rail.

More I/O modules can be added in the same manner.

R8-PA4

P. 2 / 4

EM-9739 Rev.1

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

• Protective Cover

The protective cover is to be attached over the connected I/O module

at the right end.

Align the hooks on the cover with the grooves of the module and slide it

straight until the hooks are latched.

When removing the cover, pull it out while squeezing the hooks inward.

Groove

Hook

■HOW TO UNMOUNT THE MODULE ON DIN RAIL

Caution !

1) Be careful not to hurt your hand by pointed edges of the internal

communication bus connector.

2) I/O modules cannot hold tightly on the DIN rail by themselves without

power/network module.

Secure them to the position if necessary by using DIN rail end plates.

• Removing an intermediate module

Release the locking clamps and pull out straight the module.

R8-PA4

P. 3 / 4

EM-9739 Rev.1

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

COMPONENT IDENTIFICATION

■TERMINATOR DIP SW

TERMINATOR SW SW3

Without(*) OFF

With ON

(*)Factorysetting

■PC CONFIGURATOR

The following parameters can be set with using PC Conﬁgu-

ratorSoftware(model:R8CFG):

•Pulsecountsetting(accumulatedpulsecountpreset,

max. accumulable pulse or overﬂow restet value)

•Commonsetting(lossofinternalbuscommunication

detection time)

Settings are programmed by the PC Conﬁgurator via the

Power/NetworkModule.Refertotheusersmanualforthe

R8CFGfordetailedoperationofthesoftwareprogram.

(Defaultsettingforinitialcountvalue:0,defaultsettingfor

max.accumulablepulse:4,294,967,295,default setting for

overowrestetvalue:0)

■INDICATOR LED

LED

OPERATION

FUNCTION

Status OFF Stopping

GreenON Valid host communication

GreenBlinking

Reading/writingconguration

RedON Setting error

RedBlinking Parameter error

Input

Status

OFF OFF

GreenON ON

■INPUT CONNECTOR ASSIGNMENT

•R8–PA4A

•R8–PA4B

•R8–PA4C

PIN ID FUNCTION

No.

1 24V Excitation supply 24 V

2 NC No connection

0V (COM)

Excitation supply 0 V (COM)

4 PI Discrete input

ID FUNCTION

No.

24V (COM)

Excitation supply 24 V (COM)

2 NC No connection

3 0V Excitation supply 0 V

4 PI Discrete input

ID FUNCTION

No.

1 COM Voltage input (–)

2 NC No connection

3 0V 0V

4 PI Voltage input (+)

■

Module Address

The left switch determines the tenth place digit, while the

right switch does the ones place digit of the address.

Address is selected between 0 to 28.

(Factory setting: 0)

Module Address Setting (x1)

Module Address Setting (x10)

RUN

Module Address Setting

Rotary SW

Terminator DIP SW

SW1

x10 x1

SW2

SW3Term

Status Indicator LED

Input Status Indicator LED

Internal Bus Connector

Input Connectors

FRONT VIEW SIDE VIEW

CARD ADD.

PI1

PI2

PI3

PI4

R8-PA4

P. 4 / 4

EM-9739 Rev.1

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EXTERNAL DIMENSIONS unit: mm (inch)

CONNECTION DIAGRAM

115 (4.53)6 (.24)7 (.28) 6 (.24) 7 (.28)

DIN RAIL

(35 mm wide)

[3 (.12)] [4 (.16)]

12 (.47) 59 (2.32)

55 (2.17)

WIRING INSTRUCTIONS

■e-CON connector (discrete input)

PWBconnectorXN2D-1474-S002(Omron)

RecommendedcableconnectorXN2A-1470(Omron)*1

Applicablewiresize:0.08mm2(AWG28)-0.5mm2(AWG20)

Outersheathdiameter:max.1.5dia

*1.The cable connector is not included in the package.

  Refertothespecicationsoftheproduct.

■

NPN INPUT

Control

Circuit

+24V+24V

+24V

■PNP INPUT

Control

Circuit

■VOLTAGE PULSE INPUT

COM1

0V_1

PI1

– Side

+ Side 0V

Control

Circuit

INPUT CONNECTOR 1

PI1

24V_1(COM1)

INPUT CONNECTOR 1

0V_1

PI1

INPUT CONNECTOR 1

PI1

Detection

24V_1

0V_1(COM1)

PI1

Detection

24V_1

0V_1(COM1)

PI1

24V_1 (COM1)

0V_1

PI1

COM1

0V_1

PI1

24V_4

0V_4(COM4)

PI4

24V_4 (COM4)

0V_4

PI4

COM4

0V_4

PI4

VOLTAGE

PULSE INPUT

PNP INPUT NPN INPUT

INTERNAL

POWER

INTERNAL

BUS

EXC.

SUPPLY

BUS CONNECTOR

INPUT CONNECTOR 1

INPUT CONNECTOR 4

Otros manuales de Sistema de E/S de M-system

M-system

M-system R80DCT16A2 Manual de usuario

M-system

M-system R7C-YV4 Manual de usuario

M-system

M-system R3-SS8 Manual de usuario

M-system

M-system R3-RS8B Manual de usuario

M-system

M-system R7L-DC16A Manual de usuario

M-system

M-system R5T-PA2 Manual de usuario

M-system

M-system R7 Series Manual de usuario

M-system

M-system R3-CZ4 Manual de usuario

M-system

M-system R7F4DC-DA16A-J Manual de usuario

M-system

M-system R7F4HC-DAC32D-K Manual de usuario

M-system

M-system R3-MS4 Manual de usuario

M-system

M-system Remote I/O R8 Series Manual de usuario

M-system

M-system R7HL-PA4E Manual de usuario

M-system

M-system R7E-EC8B Manual de usuario

M-system

M-system R7F4DC-DAC16C-H Manual de usuario

M-system

M-system R3-TS4 Manual de usuario

M-system

M-system R7HL-PA4E Manual de usuario

M-system

M-system R3-SS8N Manual de usuario

M-system

M-system R7ML-LC2-R Manual de usuario

M-system

M-system R8-CT4E Manual de usuario

M-system

M-system R7E-PA8-R Manual de usuario

M-system

M-system R7L-TS4 Manual de usuario

M-system

M-system R7ML-TS4 Manual de usuario

M-system

M-system R7F4HC-DA32-K Manual de usuario

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Festo

Festo CP-E08-M12-CL Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Omron

Omron SYSMAC C2000H Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD2 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario

WAGO

WAGO I/O-SYSTEM 750 Manual de usuario