M-system R7E-PA8 Manual de usuario

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7812-AV Rev.1 P. 1 / 5

INSTRUCTION MANUAL

DC VOLTAGE OUTPUT MODULE, 4 points

(High-speed Link System, isolated, 12 bits data) MODEL

R7HL-YV4L

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

DC voltage output module..................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVE

• Use dual-shield cables (Shinko Seisen Industry Model

ZHY262 PBA) for the network. If it is not sufﬁcient, use

a ferrite core (Kitagawa Industries Model GRFC-13) for

the network cable.

• The equipment must be mounted inside the instrument

panel of a metal enclosure.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

■POWER INPUT RATING & OPERATIONAL RANGE

• Locate the power input rating marked on the product and

conﬁrm its operational range as indicated below:

24V DC rating: 24V ±10%, approx. 75mA

■GENERAL PRECAUTIONS

• Before you remove the unit or mount it, turn off the power

supply and output signal for safety.

• DO NOT set the switches on the module while the power

is supplied. The switches are used only for maintenance

without the power.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

R7HL-YV4L

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7812-AV Rev.1 P. 2 / 5

COMPONENT IDENTIFICATION

X10 X1

STATION ADD.

CNFG.

12345678

78910

3452

4567

123

TERM

ON OFF

RUNPWR

■FRONT VIEW■SIDE VIEW

Terminating Resistor SW

Status Indicator LED

Station Address Setting Rotary SW

Output Terminals

Network, Power Supply

Terminals

PC Configurator Jack

Operating Mode Setting DIP SW (SW1)

■STATUS INDICATOR LED

ID COLOR FUNCTION

PWR Green Turns on when the internal 5V is sup-

plied normally.

RUN Green Turns on when the refresh data is re-

ceived normally.

■STATION ADDRESS

The left switch determines the sixteenths place digit, while

the right switch does the ones place digit of the address.

The data allocation is 1. (Range: 01H to 3FH)

Station Address Setting (x1)

Station Address Setting (x16)

■OPERATING MODE

(*) Factory setting

• Output range (SW1-3, 1-4, 1-5, 1-6)

SW1-3 SW1-4 SW1-5 SW1-6 OUTPUT RANGE

OFF OFF OFF OFF -10 – +10V DC (*)

ON OFF OFF OFF -5 – +5V DC

ON ON OFF OFF 0 – 10V DC

OFF OFF ON OFF 0 – 5V DC

ON OFF ON OFF 1 – 5V DC

ON ON ON ON

PC Conﬁgurator setting

• Output at the loss of communication (SW1-7)

SW1-7 OUTPUT AT THE LOSS OF COMMUNICATION

OFF Hold the output (*)

(maintains the last data received normally)

ON Reset the output (to 0%)

• Transfer rate (SW1-8)

SW1-8 TRANSFER RATE

Option code: None Option code: /3

OFF 12 Mbps (*) 3 Mbps

ON 6 Mbps Unused

Note: Be sure to set unused SW1-1 and 1-2 to OFF.

■TERMINATING RESISTOR

To use the terminating resistor, turn the switch ON, and

OFF to invalidate. (Factory setting OFF)

R7HL-YV4L

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7812-AV Rev.1 P. 3 / 5

■NETWORK, POWER SUPPLY TERMINAL ASSIGNMENT

• Full-duplex communication

RXD+

567

123

RXD–

24V

TXD+ TXD–

NO. ID FUNCTION, NOTES

1 TXD+ Network (slave, transmission +)

2 TXD– Network (slave, transmission –)

3 FG FG

4 RXD+ Network (master, transmission +)

5 RXD– Network (master, transmission –)

6 +24V Power input (24V DC)

7 0V Power input (0V)

• Half-duplex communication

567

123

–+

24V 0V

NC NC

NO. ID FUNCTION, NOTES

1 NC No connection

2 NC No connection

3 FG FG

4 TR+ Network

5 TR– Network

6 +24V Power input (24V DC)

7 0V Power input (0V)

■OUTPUT TERMINAL ASSIGNMENT

789

COM3

COM0

V0 V1 V2

COM1 COM2

NO. ID FUNCTION NO. ID FUNCTION

1 NC No connection 6 NC No connection

2 COM0 Common 0 7 V0 Voltage output 0

3 COM1 Common 1 8 V1 Voltage output 1

4 COM2 Common 2 9 V2 Voltage output 2

5 COM3 Common 3 10 V3 Voltage output 3

PC CONFIGURATOR

The following parameters can be set with using PC Conﬁgurator Software (model: R7CON).

Refer to the users manual for the R7CON for detailed operation of the software program.

■SETTINGS FOR INDIVIDUAL CHANNELS

PARAMETER AVAILABLE RANGE FACTORY SETTING

Output range

-10 − +10V DC

-5 − +5V DC

0 − 10V DC

0 − 5V DC

1 − 5V DC

-10 − +10V DC

Bias adjustment -320.00 − +320.00 (%) 0.00 (%)

Gain adjustment -3.2000 − +3.2000 1.0000

R7HL-YV4L

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7812-AV Rev.1 P. 4 / 5

TERMINAL CONNECTIONS

Connect the unit as in the diagram.

■EXTERNAL DIMENSIONS unit: mm (inch)

23415

789

4567

123

DIN RAIL

35mm wide

[5 (.20)]

30 (1.18)

54 (2.13)

17 (.66)

7–M3 SCREW

TERMINALS

for Network, POWER

10–M3 SCREW

TERMINALS

for OUTPUT

115 (4.53)

3 (.12)5.5 (.22) 50 (1.97) 18.5 (.73)

6 (.24) 6 (.24)

■CONNECTION DIAGRAM

Note: In order to improve EMC performance, bond the FG

terminal to ground.

Caution: FG terminal is NOT a protective conductor terminal.

COM0

COM1

COM2

COM3

24V DC

(NC) TXD–

(NC) TXD+

(TR–) RXD–

(TR+) RXD+

OUTPUT 0

OUTPUT 1

OUTPUT 2

OUTPUT 3

Note: Terminal numbers in parentheses are for half-duplex

communication model.

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.5 N·m

■SOLDERLESS TERMINAL

Refer to the drawing below for recommended ring tongue

terminal size. Spade tongue type is also applicable.

Recommended solderless terminal:

• Communication cables

Applicable wire size: 0.2 to 0.5 mm2(AWG 26 to 22)

Recommended manufacturer: Japan Solderless Terminal

MFG. Co., Ltd.

• Others

Applicable wire size: 0.25 to 1.65 mm2(AWG 22 to 16)

Recommended manufacturer: Japan Solderless Terminal

MFG. Co., Ltd. or Nichifu Co., Ltd.

4 (.16) min

3.2 (.13) dia.

mm (inch)

6 (.24) max

3.3 (.13) max

R7HL-YV4L

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7812-AV Rev.1 P. 5 / 5

COMMUNICATION CABLE CONNECTIONS

Master Module

RXD+

RXD–

TXD+

TXD–

(SHIELD)

Slave Module

RXD+

RXD–

TXD+

TXD–

(SHIELD)

Slave Module

TXD+

Terminating

Resistor

TXD–

RXD+

RXD–

SHIELD

Terminating

Resistor

Master Module

TR+

TR–

(SHIELD)

Slave Module

TR+

TR–

(SHIELD)

Slave Module

TR+

TR–

SHIELD

Note: Be sure to turn ON the switch of the terminating resistor located at both ends of the modules.

Terminating

Resistor

Terminating

Resistor

■

MASTER CONNECTION

• Full-duplex communication

• Half-duplex communication

I/O DATA DESCRIPTIONS

■ANALOG OUTPUT

ADD.n

CH0 – 3

Analog output data

CH designation of

analog output data

Unused

Analog output data

CH designation of

analog output data

Unused

• Di

■ ANALOG OUTPUT (R7HL-YV4L)

• Do

The data is 12-bit binary.

Divided by 4 times scan, 4 points output data is transferred by using CH designation bit.

For Di, the data written to Do is echoed back.

■DATA ACQUISITION PROCEDURE

1) Write the desired CH designation bit (see table below) to the CH designation bit (bit 12 to 14) for the analog output data of

Do, from the host program.

2) After one scan, the channel speciﬁed above is updated.

CHANNEL CH DESIGNATION BIT

0 000

1 001

2 010

3 011

Tabla de contenidos

Otros manuales de Sistema de E/S de M-system

M-system

M-system R7 Series Manual de usuario

M-system

M-system R80DCT16A2 Manual de usuario

M-system

M-system R6S-DA4 Manual de usuario

M-system

M-system R7D-CT4E Manual de usuario

M-system

M-system R1M-GH2T Series Manual de usuario

M-system

M-system R7F4HEIP-DAC16B Manual de usuario

M-system

M-system Devicenet R7F4DD-DA16B-C Manual de usuario

M-system

M-system R7E-PA8 Manual de usuario

M-system

M-system R7F4HC-DC32B-K Manual de usuario

M-system

M-system R7 Series Manual de usuario

M-system

M-system R8-YVT4N Manual de usuario

M-system

M-system R7ML-DC16A-R Manual de usuario

M-system

M-system R3Y-SV8N Manual de usuario

M-system

M-system R7C-DA16 Manual de usuario

M-system

M-system R7 Series Manual de usuario

M-system

M-system R7D-DC8C Manual de usuario

M-system

M-system R7M-DAC16C-R Manual de usuario

M-system

M-system R3Y-SS16N Manual de usuario

M-system

M-system Devicenet R7F4DD-DAC16C-C Manual de usuario

M-system

M-system R3-SS8 Manual de usuario

M-system

M-system R3-CT8C Manual de usuario

M-system

M-system R8-SS4N Manual de usuario

M-system

M-system R1M-P4 Manual de usuario

M-system

M-system R80 Series Manual de usuario

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Festo

Festo CP-E08-M12-CL Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Omron

Omron SYSMAC C2000H Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD2 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario

WAGO

WAGO I/O-SYSTEM 750 Manual de usuario