M-system R7HL-YV2 Manual de usuario
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-7812-D Rev.4 P. 1 / 5
INSTRUCTION MANUAL
DC VOLTAGE OUTPUT MODULE, 2 points
(High-speed Link System) MODEL R7HL-YV2
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■PACKAGE INCLUDES:
DC voltage output module..................................................(1)
■MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■CONFORMITY WITH EU DIRECTIVE
• Use dual-shield cables (Shinko Seisen Industry Model
ZHY262 PBA) for the network. If it is not sufficient, use
a ferrite core (Kitagawa Industries Model GRFC-13) for
the network cable.
• The equipment must be mounted inside the instrument
panel of a metal enclosure.
• The actual installation environments such as panel con-
figurations, connected devices, connected wires, may af-
fect the protection level of this unit when it is integrated
in a panel system. The user may have to review the CE
requirements in regard to the whole system and employ
additional protective measures to ensure the CE conform-
ity.
■POWER INPUT RATING & OPERATIONAL RANGE
• Locate the power input rating marked on the product and
confirm its operational range as indicated below:
24V DC rating: 24V ±10%, approx. 100mA
■GENERAL PRECAUTIONS
• Before you remove the unit or mount it, turn off the power
supply and output signal for safety.
• DO NOT set the switches on the module while the power
is supplied. The switches are used only for maintenance
without the power.
■ENVIRONMENT
• Indoor use.
• When heavy dust or metal particles are present in the
air, install the unit inside proper housing with sufficient
ventilation.
• Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
• Environmental temperature must be within -10 to +55°C
(14 to 131°F) with relative humidity within 30 to 90% RH
in order to ensure adequate life span and operation.
■WIRING
• Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).
• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
■AND ....
• The unit is designed to function as soon as power is sup-
plied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data
sheet.
R7HL-YV2
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-7812-D Rev.4 P. 2 / 5
COMPONENT IDENTIFICATION
X10 X1
STATION ADD.
CNFG.
12345678
78910
3452
6
1
4567
123
TERM
ON OFF
RUNPWR
ON
■FRONT VIEW■SIDE VIEW
Terminating Resistor SW
Status Indicator LED
Station Address Setting Rotary SW
Output Terminals
Network, Power Supply
Terminals
PC Configurator Jack
Operating Mode Setting DIP SW (SW1)
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
■STATUS INDICATOR LED
ID COLOR FUNCTION
PWR Green Turns on when the internal 5V is sup-
plied normally.
RUN Green Turns on when the refresh data is re-
ceived normally.
■STATION ADDRESS
The left switch determines the sixteenths place digit, while
the right switch does the ones place digit of the address.
The data allocation is 2.
• Full-duplex communication
Setting “n” with the rotary switches, the addresses are n
and n+2. (Range: 01H to 3DH)
• Half-duplex communication
Two (2) addresses are assigned from the one set with the
rotary switch. (Range: 01H to 3EH)
Station Address Setting (x1)
Station Address Setting (x16)
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
■OPERATING MODE
(*) Factory setting
• Output range (SW1-3, 1-4, 1-5, 1-6)
SW1-3 SW1-4 SW1-5 SW1-6 OUTPUT RANGE
OFF OFF OFF OFF -10 – +10V DC (*)
ON OFF OFF OFF -5 – +5V DC
OFF ON OFF OFF -1 – +1V DC
ON ON OFF OFF 0 – 10V DC
OFF OFF ON OFF 0 – 5V DC
ON OFF ON OFF 1 – 5V DC
OFF ON ON OFF 0 – 1V DC
ON ON ON OFF -0.5 – +0.5V DC
ON ON ON ON
PC Configurator setting
• Output at the loss of communication (SW1-7)
SW1-7 OUTPUT AT THE LOSS OF COMMUNICATION
OFF Hold the output (*)
(maintains the last data received normally)
ON Reset the output (to -15% or approx. -11.5V DC)
• Transfer rate (SW1-8)
SW1-8 TRANSFER RATE
OFF 12 Mbps (*)
ON 6 Mbps
Note: Be sure to set unused SW1-1 and 1-2 to OFF.
■TERMINATING RESISTOR
To use the terminating resistor, turn the switch ON, and
OFF to invalidate. (Factory setting OFF)
R7HL-YV2
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-7812-D Rev.4 P. 3 / 5
■NETWORK, POWER SUPPLY TERMINAL ASSIGNMENT
• Full-duplex communication
4
RXD+
567
123
RXD–
+
24V
0V
TXD+ TXD–
FG
NO. ID FUNCTION, NOTES
1 TXD+ Network (slave, transmission +)
2 TXD– Network (slave, transmission –)
3 FG FG
4 RXD+ Network (master, transmission +)
5 RXD– Network (master, transmission –)
6 +24V Power input (24V DC)
7 0V Power input (0V)
• Half-duplex communication
4
TR
+
567
123
TR
–+
24V 0V
NC NC
FG
NO. ID FUNCTION, NOTES
1 NC No connection
2 NC No connection
3 FG FG
4 TR+ Network
5 TR– Network
6 +24V Power input (24V DC)
7 0V Power input (0V)
■OUTPUT TERMINAL ASSIGNMENT
6
NC
7
VH0
8
VL0
1
NC
2
COM0
3
COM0
9
VH1
4
COM1
10
VL1
5
COM1
NO. ID FUNCTION NO. ID FUNCTION
1 NC
No connection
6 NC
No connection
2 COM0 Common 0 7 VH0
Wide span volt. 0
3 COM0 Common 0 8 VL0
Narrow span volt. 0
4 COM1 Common 1 9 VH1
Wide span volt. 1
5 COM1 Common 1 10 VL1
Narrow span volt. 1
■OUTPUT RANGE
• Wide span : -10 to +10V DC, -5 to +5V DC, 0 to 10V DC,
0 to 5V DC, 1 to 5V DC
• Narrow span: -1 to +1V DC, 0 to 1V, -0.5 to +0.5V DC
PC CONFIGURATOR
With configurator software, settings shown below are available.
Refer to the software manual of R7CON for detailed operation.
■CHANNEL INDIVIDUAL SETTING
PARAMETER AVAILABLE RANGE DEFAULT SETTING
Output Range -10 to +10 V DC
-5 to +5 V DC
-1 to +1 V DC
0 to 10 V DC
0 to 5 V DC
1 to 5 V DC
0 to 1 V DC
-0.5 to +0.5 V DC
-10 to +10 V DC
Zero scale -32000 to +32000 0
Full scale -32000 to +32000 10000
Bias -320.00 to +320.00 0.00
Gain -3.2000 to +3.2000 1.0000
R7HL-YV2
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-7812-D Rev.4 P. 4 / 5
TERMINAL CONNECTIONS
Connect the unit as in the diagram.
■EXTERMNAL DIMENSIONS unit: mm (inch)
23415
10
789
6
4567
123
DIN RAIL
35mm wide
[5 (.20)]
30 (1.18)
54 (2.13)
17 (.66)
7–M3 SCREW
TERMINALS
for Network, POWER
10–M3 SCREW
TERMINALS
for OUTPUT
115 (4.53)
3 (.12)5.5 (.22) 50 (1.97) 18.5 (.73)
6 (.24) 6 (.24)
■CONNECTION DIAGRAM
4
7
6
3
2
1
5
7VH0
8VL0
2COM0
3COM0
OUTPUT 0
9VH1
10
VL1
4COM1
5COM1
OUTPUT 1
VHn
VLn
+
–
COMn
WIDE SPAN
VOLTAGE
VHn
VLn +
–
COMn
NARROW SPAN
VOLTAGE
FG
24V DC
0V
TXD– (NC)
TXD+ (NC)
RXD– (TR–)
RXD+ (TR+)
■ Output Connection Examples
Note 1: Te rminal numbers in parentheses are for half-duplex
communication model.
Note 2: In order to improve EMC performance, bond the FG
terminal to ground.
Caution: FG terminal is NOT a protective conductor terminal.
WIRING INSTRUCTIONS
■SCREW TERMINAL
Torque: 0.5 N·m
■SOLDERLESS TERMINAL
Refer to the drawing below for recommended ring tongue
terminal size. Spade tongue type is also applicable.
Recommended solderless terminal:
• Communication cables
Applicable wire size: 0.2 to 0.5 mm2(AWG 26 to 22)
Recommended manufacturer: Japan Solderless Terminal
MFG. Co., Ltd.
• Others
Applicable wire size: 0.25 to 1.65 mm2(AWG 22 to 16)
Recommended manufacturer: Japan Solderless Terminal
MFG. Co., Ltd. or Nichifu Co., Ltd.
4 (.16) min
3.2 (.13) dia.
mm (inch)
6 (.24) max
3.3 (.13) max
R7HL-YV2
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-7812-D Rev.4 P. 5 / 5
COMMUNICATION CABLE CONNECTIONS
Master Module
RXD+
RXD–
TXD+
TXD–
FG
(SHIELD)
Slave Module
RXD+
RXD–
TXD+
TXD–
FG
(SHIELD)
Slave Module
TXD+
Terminating
Resistor
TXD–
RXD+
RXD–
SHIELD
Terminating
Resistor
Master Module
TR+
TR–
FG
(SHIELD)
Slave Module
TR+
TR–
FG
(SHIELD)
Slave Module
TR+
TR–
SHIELD
Note: Be sure to turn ON the switch of the terminating resistor located at both ends of the modules.
Terminating
Resistor
Terminating
Resistor
■
MASTER CONNECTION
• Full-duplex communication
• Half-duplex communication
I/O DATA DESCRIPTIONS
Scaling of analog output is configurable with the configurator software (model: R7CON). Refer to the software manual for
details.
■ANALOG OUTPUT
0
15
CH0Unused
Unused CH1
0
15
0
15
0
15
• Di • Do
ADD.n
(ADD.n)
CH0
CH1
ADD.n+2
(ADD.n+1)
The data is 16-bit binary.
Negative value is represented in 2’s complements.
Address in parentheses are for half-duplex mode.
Tabla de contenidos
Otros manuales de Sistema de E/S de M-system
M-system
M-system Devicenet R7F4DD-DAC16C-C Manual de usuario
M-system
M-system Devicenet R7F4DD-DA16A-H Manual de usuario
M-system
M-system R7D-YS2/UL Manual de usuario
M-system
M-system R7L-DAC16 Manual de usuario
M-system
M-system R7 Series Manual de usuario
M-system
M-system R3S-RS4A Manual de usuario
M-system
M-system R7K4DH-1-DAC32A Manual de usuario
M-system
M-system R3-TS4 Manual de usuario
M-system
M-system R30US4 Manual de usuario
M-system
M-system R3S-DA16 Manual de usuario
M-system
M-system R3Y-SV8N Manual de usuario
M-system
M-system R7F4DC-DAC16C-H Manual de usuario
M-system
M-system R7L-TS4 Manual de usuario
M-system
M-system R30MS4 Manual de usuario
M-system
M-system R8-YS2 Manual de usuario
M-system
M-system R30NE1 Manual de usuario
M-system
M-system M8BS2-042 Manual de usuario
M-system
M-system R7D-SV4 Manual de usuario
M-system
M-system R7ML-LC2-R Manual de usuario
M-system
M-system R3Y-DC16 Manual de usuario
Manuales populares de Sistema de E/S de otras marcas
WAGO
WAGO 750-344 Manual de usuario
Teknim
Teknim TWM-1887 Manual de instrucciones
Intelligent Appliance
Intelligent Appliance IA-2662-E Manual de usuario
BERGHOF
BERGHOF ECC DIO 16/16 Manual de instrucciones
Advantech
Advantech PCM-27J3AU Manual de instalación y operación
Festo
Festo CP-E08-M12-CL Manual de usuario
