M-system R7 Series Manual de usuario

EM-7812-E Rev.4 P. 1 / 5

INSTRUCTION MANUAL

DC CURRENT OUTPUT MODULE, 2 points

(High-speed Link System) MODEL R7HL-YS2

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

DC current output module..................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVE

• Use dual-shield cables (Shinko Seisen Industry Model

ZHY262 PBA) for the network. If it is not sufﬁcient, use

a ferrite core (Kitagawa Industries Model GRFC-13) for

the network cable.

• The equipment must be mounted inside the instrument

panel of a metal enclosure.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

■POWER INPUT RATING & OPERATIONAL RANGE

• Locate the power input rating marked on the product and

conﬁrm its operational range as indicated below:

24V DC rating: 24V ±10%, approx. 140mA

■GENERAL PRECAUTIONS

• Before you remove the unit or mount it, turn off the power

supply and output signal for safety.

• DO NOT set the switches on the module while the power

is supplied. The switches are used only for maintenance

without the power.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7HL-YS2

EM-7812-E Rev.4 P. 2 / 5

COMPONENT IDENTIFICATION

X10 X1

STATION ADD.

CNFG.

12345678

78910

3452

4567

123

TERM

ON OFF

RUNPWR

■FRONT VIEW■SIDE VIEW

Terminating Resistor SW

Status Indicator LED

Station Address Setting Rotary SW

Output Terminals

Network, Power Supply

Terminals

PC Configurator Jack

Operating Mode Setting DIP SW (SW1)

■STATUS INDICATOR LED

ID COLOR FUNCTION

PWR Green Turns on when the internal 5V is sup-

plied normally.

RUN Green Turns on when the refresh data is re-

ceived normally.

■STATION ADDRESS

The left switch determines the sixteenths place digit, while

the right switch does the ones place digit of the address.

The data allocation is 2.

• Full-duplex communication

Setting “n” with the rotary switches, the addresses are n

and n+2. (Range: 01H to 3DH)

• Half-duplex communication

Two (2) addresses are assigned from the one set with the

rotary switch. (Range: 01H to 3EH)

Station Address Setting (x1)

Station Address Setting (x16)

■OPERATING MODE

(*) Factory setting

• Output at the loss of communication (SW1-7)

SW1-7 OUTPUT AT THE LOSS OF COMMUNICATION

OFF Hold the output (*)

(maintains the last data received normally)

ON Reset the output (to -15%)

• Transfer rate (SW1-8)

SW1-8 TRANSFER RATE

OFF 12 Mbps (*)

ON 6 Mbps

Note: Be sure to set unused SW1-1 through 1-6 to OFF.

■TERMINATING RESISTOR

To use the terminating resistor, turn the switch ON, and

OFF to invalidate. (Factory setting OFF)

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7HL-YS2

EM-7812-E Rev.4 P. 3 / 5

■NETWORK, POWER SUPPLY TERMINAL ASSIGNMENT

• Full-duplex communication

RXD+

567

123

RXD–

24V

TXD+ TXD–

NO. ID FUNCTION, NOTES

1 TXD+ Network (slave, transmission +)

2 TXD– Network (slave, transmission –)

3 FG FG

4 RXD+ Network (master, transmission +)

5 RXD– Network (master, transmission –)

6 +24V Power input (24V DC)

7 0V Power input (0V)

• Half-duplex communication

567

123

–+

24V 0V

NC NC

NO. ID FUNCTION, NOTES

1 NC No connection

2 NC No connection

3 FG FG

4 TR+ Network

5 TR– Network

6 +24V Power input (24V DC)

7 0V Power input (0V)

■OUTPUT TERMINAL ASSIGNMENT

COM0

COM1

NO. ID FUNCTION NO. ID FUNCTION

1 NC

No connection

6 NC

No connection

2 COM0 Common 0 7 I0 Current 0

3 NC

No connection

8 NC

No connection

4 COM1 Common 1 9 I1 Current 1

5 NC

No connection

10 NC

No connection

PC CONFIGURATOR

With conﬁgurator software, settings shown below are available.

Refer to the software manual of R7CON for detailed operation.

■CHANNEL INDIVIDUAL SETTING

PARAMETER AVAILABLE RANGE DEFAULT SETTING

Zero scale -32000 to +32000 0

Full scale -32000 to +32000 10000

Bias -320.00 to +320.00 0.00

Gain -3.2000 to +3.2000 1.0000

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7HL-YS2

EM-7812-E Rev.4 P. 4 / 5

TERMINAL CONNECTIONS

Connect the unit as in the diagram.

■EXTERMNAL DIMENSIONS unit: mm (inch)

23415

789

4567

123

DIN RAIL

35mm wide

[5 (.20)]

30 (1.18)

54 (2.13)

17 (.66)

7–M3 SCREW

TERMINALS

for Network, POWER

10–M3 SCREW

TERMINALS

for OUTPUT

115 (4.53)

3 (.12)5.5 (.22) 50 (1.97) 18.5 (.73)

6 (.24) 6 (.24)

■CONNECTION DIAGRAM

COM0

COM1

24V DC

TXD– (NC)

TXD+ (NC)

RXD–(TR–)

RXD+(TR+)

OUTPUT 0

OUTPUT 1

Note 1: Te rminal numbers in parentheses are for half-duplex

communication model.

Note 2: In order to improve EMC performance, bond the FG

terminal to ground.

Caution: FG terminal is NOT a protective conductor terminal.

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.5 N·m

■SOLDERLESS TERMINAL

Refer to the drawing below for recommended ring tongue

terminal size. Spade tongue type is also applicable.

Recommended solderless terminal:

• Communication cables

Applicable wire size: 0.2 to 0.5 mm2(AWG 26 to 22)

Recommended manufacturer: Japan Solderless Terminal

MFG. Co., Ltd.

• Others

Applicable wire size: 0.25 to 1.65 mm2(AWG 22 to 16)

Recommended manufacturer: Japan Solderless Terminal

MFG. Co., Ltd. or Nichifu Co., Ltd.

4 (.16) min

3.2 (.13) dia.

mm (inch)

6 (.24) max

3.3 (.13) max

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7HL-YS2

EM-7812-E Rev.4 P. 5 / 5

COMMUNICATION CABLE CONNECTIONS

Master Module

RXD+

RXD–

TXD+

TXD–

(SHIELD)

Slave Module

RXD+

RXD–

TXD+

TXD–

(SHIELD)

Slave Module

TXD+

Terminating

Resistor

TXD–

RXD+

RXD–

SHIELD

Terminating

Resistor

Master Module

TR+

TR–

(SHIELD)

Slave Module

TR+

TR–

(SHIELD)

Slave Module

TR+

TR–

SHIELD

Note: Be sure to turn ON the switch of the terminating resistor located at both ends of the modules.

Terminating

Resistor

Terminating

Resistor

■

MASTER CONNECTION

• Full-duplex communication

• Half-duplex communication

I/O DATA DESCRIPTIONS

Scaling of analog output is conﬁgurable with the conﬁgurator software (model: R7CON). Refer to the software manual for

details.

■ANALOG OUTPUT

CH0Unused

Unused CH1

• Di • Do

ADD.n

(ADD.n)

CH0

CH1

ADD.n+2

(ADD.n+1)

The data is 16-bit binary.

Negative value is represented in 2’s complements.

Address in parentheses are for half-duplex mode.

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

Otros manuales para R7 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de E/S de M-system

M-system

M-system R7M-DC4G-R Manual de usuario

M-system

M-system R5 Series Manual de usuario

M-system

M-system R80DCT16A2 Manual de usuario

M-system

M-system R3-DA64A Manual de usuario

M-system

M-system R7K4F Series Manual de usuario

M-system

M-system R7ML-LC2 Manual de usuario

M-system

M-system R1M-D1 Manual de usuario

M-system

M-system R7M-DA16F Manual de usuario

M-system

M-system R7D-PA8 Manual de usuario

M-system

M-system R7D-YV2 Manual de usuario

M-system

M-system R7 Series Manual de usuario

M-system

M-system 6BSN Manual de usuario

M-system

M-system R7M-MS4-R Manual de usuario

M-system

M-system R30SVF4 Manual de usuario

M-system

M-system R7F4DC-DA16A-C Manual de usuario

M-system

M-system Mini-MW Series Manual de usuario

M-system

M-system R5-SV Manual de usuario

M-system

M-system R7L-DAC16 Manual de usuario

M-system

M-system R7ML-TS4 Manual de usuario

M-system

M-system R3-SV8 Manual de usuario

M-system

M-system R3-SV8A Manual de usuario

M-system

M-system R7F4HC-DC32B-K Manual de usuario

M-system

M-system R30US4 Manual de usuario

M-system

M-system R7M-DA16-R Manual de usuario

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Festo

Festo CP-E08-M12-CL Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Omron

Omron SYSMAC C2000H Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD2 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario

WAGO

WAGO I/O-SYSTEM 750 Manual de usuario