M-system R3-WT1 Manual de usuario

R3-WT1

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax:

+81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8388 Rev.3 P. 1 / 5

MULTI POWER INPUT MODULE MODEL R3-WT1

INSTRUCTION MANUAL

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

the contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Multi power input module .............................................(1)

■MODEL NO.

Conﬁrm that the model number described on the product is

exactly what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

In order to set up the software setting of this module, PC

Conﬁgurator Software (model: R3CON) is required. For

more information, please refer to the users manual for the

R3CON.

The R3CON PC Conﬁgurator Software is downloadable at

MSystem’s web site: http://www.m-system.co.jp.

POINTS OF CAUTION

■HOT INSERTION/REMOVAL OF MODULES

•Removing or replacing modules does not affect other mod-

ules on the same backplane. It is possible to replace them

without removing the power supply. However, replacing

multiple modules at once may greatly change line voltage

levels. We recommend that you replace them one by one.

■ENVIRONMENT

•Indoor use

•When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

•Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

•Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

•Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

•Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

•The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

INSTALLATION

Use the Installation Base (model: R3-BSx).

R3-WT1

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax:

+81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8388 Rev.3 P. 2 / 5

COMPONENT IDENTIFICATION

■FRONT VIEW

RUN LED

ERR LED

■SIDE VIEW

SW1SW2

SW3

■SIDE DIP SW

(*) Factory setting

Be sure to turn off the power supply to the module when-

changing settings. Reset the count after setting changes.

• SW1, SW2

Count Reset Enable : Back to 0 at overﬂow

Disable : Halt at 999 999 999

Power Factor may start hunting around 1.

SW FUNCTION 0 : OFF(*)1 : ON

SW1-2 active energy count reset disable enable

SW1-3 active energy

bidirectional current

disable enable*1

SW1-6 active energy count reset disable enable

SW1-7 active energy

bidirectional current

disable enable*1

SW2-1 power factor LEAD polarity normal inverted

*1. Both active energy count reset and reactive energycount re-

set are ﬁxed at ‘disable.’

The count stops at ±999 999 999.

When the bidirectional current computation is enabled,the

outgoing active energy and the LEAD reactive energy be-

come 0.

Power Factor Polarity

-1.0

1.0

COS

DEG

90-90-180

(LEAD)

180

(LAG)

Inverted

Normal

• SW3

The maximum available active energy count is 10

SW 0 : OFF(*)1 : ON

SW3-1 ---- count reset

How to Reset

Set the SW3-1 to ON and turn on the power supply. Wait

until the RUN LED (red) starts ﬂashing and the ERR LED

(green) turns on. Then turn the power supply off and reset

the SW3-1 to OFF.

Turn all switches off other than the above.

■STATUS INDICATOR LED

RUN indicator: Bi-color (red/green) LED;

Red when the bus A operates normally;

Green when the bus B operates normally;

Amber when both buses operate normally.

ERR indicator: Bi-color (red/green) LED;

Red with the input abnormality;

Green in normal operating conditions.

R3-WT1

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax:

+81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8388 Rev.3 P. 3 / 5

PC CONFIGURATOR

The following parameters can be set with using PC Conﬁgurator Software (model: R3CON):

•Enter ﬁne 0% adjustment value

•Enter ﬁne 100% adjustment value

•Low-end cutout value in %

•Primary voltage

•Primary voltage, Exponent (10n)

•Primary current

•Primary current, exponent 10n

•Active/Reactive Power, span value

•Active/Reactive Power, exponent 10n

•Active Energy unit, exponent 10n

•Minimum totalized value

•Maximum totalized value

•Reactive Energy unit, exponent 10n

•Minimum totalized value

•Maximum totalized value

TRANSMISSION DATA DESCRIPTIONS

ADDRESS CONTENTS

n Active power *2

n + 1 Reactive power *2

n + 2 Power factor *2

n + 3 Frequency *2

n + 4 Incoming active energy (lower bits) *3

n + 5 Incoming active energy (upper bits)

n + 6 Outgoing active energy (lower bits) *3

n + 7 Outgoing active energy (upper bits)

n + 8 LAG reactive energy (lower bits) *3

n + 9 LAG reactive energy (upper bits)

n +10 LEAD reactive energy (lower bits) *3

n +11 LEAD reactive energy (upper bits)

n +12 0

n +13 0

n +14 0

n +15 0

R3CON type ID WT1****

Network module 4, 8, 16

data allocation

mode example *1

n = I/O address on the installation base

Factory setting = 1 kWh and 1 kvarh per bit.

Data address depends upon the data allocation mode as

indicated below:

4 (n thr. n+3)

8 (n thr. n+7)

16 (n thr. n+15)

*1. Fixed at 16 for the R3-NPx.

*2. 16-bit data

*3. 32-bit data

I/O DATA DESCRIPTIONS

■16-BIT DATA

■

16-bit binary data. Minus values are represented in 2’s complements.

32-BIT DATA

1631

stigidrewolstigidreppu

32-bit binary data. Minus values are represented in 2’s complements.

R3-WT1

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax:

+81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8388 Rev.3 P. 4 / 5

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■DIMENSIONS mm (inch)

130 (5.12)

52.5 (2.07) 109 (4.29)

7.9

(.31)

10–M3.5

SCREW

POSITIONING

GUIDE

TERMINAL

COVER

■CONNECTION DIAGRAM

BUS CONNECTOR

INTERNAL

POWER

INTERNAL

BUS A

INTERNAL

BUS B*

VOLTAGE

INPUT

LOAD

123

SOURCE

P2V

P1U

FUSE VT

CURRENT

INPUT

LOAD

123

SOURCE

■3-PHASE/3-WIRE

BUS CONNECTOR

INTERNAL

POWER

INTERNAL

BUS A

INTERNAL

BUS B*

■SINGLE-PHASE/3-WIRE

BUS CONNECTOR

INTERNAL

POWER

INTERNAL

BUS A

INTERNAL

BUS B*

■SINGLE-PHASE/2-WIRE

VOLTAGE

INPUT

LOAD

SOURCE

FUSE

CURRENT

INPUT

LOAD

SOURCE

*For dual redundant communication.

VOLTAGE

INPUT

LOAD

1N2

SOURCE

P0V

P1U

FUSE VT

CURRENT

INPUT

LOAD

1N2

SOURCE

R3-WT1

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax:

+81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8388 Rev.3 P. 5 / 5

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.8 N·m

■SOLDERLESS TERMINAL mm (inch)

Refer to the drawing below for recommended ring tongue

terminal size. Spade tongue type is also applicable. Solder-

less terminals with insulation sleeve do not ﬁt.

Applicable wire size: 0.75 – 2 mm2

3.7 (.15) dia.

6 min.

(.24)

14.5 (.57) max.

7 max.

(.28)

3.5 (.14) max.

Tabla de contenidos

Otros manuales de Sistema de E/S de M-system

M-system

M-system R7D-TS4 Manual de usuario

M-system

M-system R3-SV4A Manual de usuario

M-system

M-system R7F4DC-DAC16C-H Manual de usuario

M-system

M-system R7E-MS4 Manual de usuario

M-system

M-system Devicenet R7F4DD-DA16A-C Manual de usuario

M-system

M-system R7 Series Manual de usuario

M-system

M-system R7ML-DA16 Manual de usuario

M-system

M-system R3-SV8A Manual de usuario

M-system

M-system R8-SS4N Manual de usuario

M-system

M-system R7D-YV2/UL Manual de usuario

M-system

M-system R30NCIE1 Manual de usuario

M-system

M-system Devicenet R7F4DD-DC16B-H Manual de usuario

M-system

M-system Devicenet R7F4DD-DA16B-C Manual de usuario

M-system

M-system R1M Series Manual de usuario

M-system

M-system R7M-CT4E-R Manual de usuario

M-system

M-system R3-SV4 Manual de usuario

M-system

M-system R10M-CT4E Manual de usuario

M-system

M-system R7 Series Manual de usuario

M-system

M-system R7D-SV4 Manual de usuario

M-system

M-system R3-RS4 Manual de usuario

M-system

M-system R7F4HEIP-DAC16C Manual de usuario

M-system

M-system R7E-PA8 Manual de usuario

M-system

M-system R3-SS16N Manual de usuario

M-system

M-system R30SVF4 Manual de usuario

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Festo

Festo CP-E08-M12-CL Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Omron

Omron SYSMAC C2000H Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD2 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario

WAGO

WAGO I/O-SYSTEM 750 Manual de usuario