M-system R3-RS4 Manual de usuario

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8364 Rev.5 P. 1 / 4

INSTRUCTION MANUAL

RTD INPUT MODULE

(4 points, isolated) MODEL R3-RS4

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

RTD input module...............................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

• The equipment must be mounted inside the instrument

panel of a metal enclosure.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

■HOT SWAPPABLE MODULES

• Replacing the module does not affect other modules on

the same base. Thus, the module can be replaced while

the power is ON. However, replacing multiple modules

at once may greatly change live voltage levels. We highly

recommend to replace them one by one.

■GENERAL PRECAUTIONS

• DO NOT set the switches on the module while the power

is supplied. The switches are used only for maintenance

without the power.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

INSTALLATION

Use the Installation Base (model: R3-BSx).

R3-RS4

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8364 Rev.5 P. 2 / 4

COMPONENT IDENTIFICATION

SW1SW2

SW3

■FRONT VIEW ■SIDE VIEW

ERR LED

RUN LED

Conv.

Rate

Temp.

Unit

Input 2 (SW1)

Input 4 (SW2)

RTD

Input 1 (SW1)

Input 3 (SW2)

Burnout

Functions

■STATUS INDICATOR LED

RUN indicator: Bi-color (red/green) LED;

Red when the bus A operates normally;

Green when the bus B operates normally;

Amber when both buses operate normally.

ERR indicator: Bi-color (red/green) LED;

Red with burnout;

Green in normal operating conditions.

■SIDE DIP SW

(*) Factory setting

• RTD Type: SW1, SW2

INPUT 1 (SW1) INPUT 2 (SW1)

RTDINPUT 3 (SW2) INPUT 4 (SW2)

12345678

OFF OFF OFF OFF OFF OFF OFF OFF

Pt 100 (*)

(JIS ’97, IEC)

OFF OFF OFF

Pt 100

(JIS ’89)

OFF

OFF OFF OFF

OFF OFF

JPt 100

(JIS ’89)

ON ON

OFF OFF

ON ON

OFF OFF

Pt 50Ω

(JIS ’81)

OFF OFF

OFF OFF OFF

OFF

Ni 100

OFF

Cu 10 @ 25°C

OFF

ON ON

OFF OFF

ON ON

OFF

Pt 1000

ON ON ON

OFF

ON ON ON

OFF

Ni 508.4Ω

OFF OFF OFF

ON Cu 50

OFF OFF

ON ON

OFF OFF

ON Ni 1000

• Burnout: SW3-1

SW3-1 BURNOUT

OFF Upscale (*)

ON Downscale

• Temperature Unit: SW3-2, 3-3

SW3-2 SW3-3 TEMP. UNIT

OFF OFF °C (*)

ON OFF °F

OFF ON K (Absolute Temp)

• Conversion Rate: SW3-4

SW3-4 CONV. RATE

OFF 250 msec. (*)

ON 1 sec.

R3-RS4

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8364 Rev.5 P. 3 / 4

PC CONFIGURATOR

With conﬁgurator software, settings shown below are available.

Refer to the software manual of R3CON for detailed operation.

■CHANNEL INDIVIDUAL SETTING

PARAMETER AVAILABLE RANGE DEFAULT SETTING

Zero Scale -32000 to +32000 0

Full Scale -32000 to +32000 10000

Zero Adjust -320.00 to +320.00 0.00

Full Adjust -32000 to +32000 1.0000

Zero Base Depends on sensor type 0.00

Full Base Depends on sensor type 0.00

Unused 0: Enable

1: Disable

0: Enable

■CHANNEL BATCH SETTING

PARAMETER AVAILABLE RANGE DEFAULT SETTING

Limit No check mark: Limits to the scaling values equivalent

to -15 % to +115 %.

Check-marked: Limits within Zero Scale to Full Scale.

No check mark

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■EXTERNAL DIMENSIONS unit: mm (inch)

130 (5.12)

27.5 (1.08) 109 (4.29) POSITIONING

GUIDE

TERMINAL

COVER

20–M3

SCREW

6.2

(.24)

R3-RS4

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8364 Rev.5 P. 4 / 4

■CONNECTION DIAGRAM

RTD

*For dual redundant communication.

INPUT 1

RTD

INPUT 2

RTD

INPUT 3

RTD

INPUT 4

BUS CONNECTOR

INTERNAL POWER

INTERNAL BUS A

INTERNAL BUS B*

• Unused Input Channels

Close across the unused input terminals with a resistor as shown

below and set the DIP switch for Pt 100 input.

Unused channels left open are equal to the burnout, which turns

the red ERR LED on and sets a burnout flag at the PLC or the

host device.

Unused channels can be specified and set so on the PC

Configurator Software (model: R3CON) without needing to connect

resistors at the field terminals.

INPUT 1

INPUT 2

INPUT 3

INPUT 4

100Ω

11 13 16 18

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.5 N·m

■SOLDERLESS TERMINAL

Refer to the drawing below for recommended ring tongue

terminal size. Spade tongue type is also applicable. Solder-

less terminals with insulation sleeve do not ﬁt.

Applicable wire size: 0.3 – 0.75 mm2

Recommended manufacturer: Japan Solderless Terminal

MFG. Co., Ltd., Nichifu Co., Ltd.

12max

6max

3max 4min

3.2 dia.

(mm)

Otros manuales de Sistema de E/S de M-system

M-system

M-system R6S-DA4 Manual de usuario

M-system

M-system M5SN Manual de usuario

M-system

M-system R3S-RS4A Manual de usuario

M-system

M-system R7L-DC16A-R Manual de usuario

M-system

M-system R3-CT8C Manual de usuario

M-system

M-system M8BS2-042 Manual de usuario

M-system

M-system MDR-8 Manual de usuario

M-system

M-system M8BS2-041 Manual de usuario

M-system

M-system R80DAT16A2 Manual de usuario

M-system

M-system R7M-EA8/UL Manual de usuario

M-system

M-system R7L-DAC16 Manual de usuario

M-system

M-system R7L-DC16B Manual de usuario

M-system

M-system R7ML-LC2 Manual de usuario

M-system

M-system R5-SV Manual de usuario

M-system

M-system R7D-SV4 Manual de usuario

M-system

M-system R7L-DC16B-R Manual de usuario

M-system

M-system R30SVF4 Manual de usuario

M-system

M-system R7F4DC-DA16A-C Manual de usuario

M-system

M-system R7D-TS4 Manual de usuario

M-system

M-system R7ML-TS4 Manual de usuario

M-system

M-system R10M-CT4E Manual de usuario

M-system

M-system R7I4DML3-DA32A Manual de usuario

M-system

M-system R7C-CT4E Manual de usuario

M-system

M-system R7M-TS4-R Manual de usuario

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Festo

Festo CP-E08-M12-CL Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Omron

Omron SYSMAC C2000H Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD2 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario

WAGO

WAGO I/O-SYSTEM 750 Manual de usuario