Loctite CL10 Manual de usuario
EQUIPMENT
Operation Manual
LoctiteCL10 Quad LED Controller
Part Number 1514634
2
Contents
1CAUTION·························································································4
1.1 SAFETY INSTRUCTION ····································································5
1.2 OUT OF BOX INSPECTION································································5
1.3 PACKING LIST ··············································································6
2OVERVIEW······················································································6
3TECHNICAL DATA············································································7
4INSTALLATION ················································································8
4.1 CAPACITY ··················································································8
4.2 DIMENSION·················································································9
4.3 CAUTION·················································································· 10
4.4 INSTALLATION FLOW···································································· 11
5CONTROLLER BUTTON AND OPERATING PANEL ····························· 14
5.1 COMPONENT NAME AND FUNCTION··················································· 14
5.2 BUTTON AND OPERATING PANEL INSTRUCTIONS···································· 15
5.2.1 CONTROLLER BUTTON INSTRUCTION·············································· 15
5.2.2 LCD DISPLAY INSTRUCTION························································ 16
5.2.3 PARAMETER CURSOR STATUS······················································ 16
5.2.4 INFORMATION ON LCD DISPLAY ··················································· 16
5.3 OPERATION·············································································· 17
5.3.1 STARTUP··············································································· 17
5.3.2 STARTING CONTROLLER ··························································· 18
5.3.3 WORKING MODE
：
································································· 19
5.3.4 EXIT WORKING MODE
：
···························································· 19
5.3.5 STANDBY MODE SETTING
：
························································· 20
5.3.6 PASSWORD SETTING IN PARAMETER PANEL ······································ 20
5.4 PARAMETER SETTING ································································ 22
5.4.1 ENTER PARAMETER PANEL························································· 22
5.4.2 WORKING MODE SETUP····························································· 23
5.5 WORKING MODE DESCRIPTION ······················································ 25
5.5.1 C.C MODE············································································· 25
5.5.2 PWM MODE··········································································· 25
5.5.3 STEP MODE ··········································································· 25
5.5.4 OPT MODE············································································ 25
5.5.5 MANUAL MODE········································································ 25
5.6 PARAMETER
（
INTENSITY
）
SETTING················································ 26
5.7 FOOT SWITCH SETUP
：
······························································· 27
5.8 TIME SETTING
：
········································································ 28
5.9 STEP MODE ············································································· 29
5.9.1 TIME SETUP IN STEP MODE························································· 30
5.9.2 INTENSITY SETTING ·································································· 31
3
5.10 LANGUAGE SETTING·································································· 32
5.11 LED HEAD UNIT AND FOOT SWITCH··············································· 33
5.12 SHUTDOWN ············································································ 34
6TROUBLESHOOTING······································································ 35
7REPLACEMENT PARTS ·································································· 37
8APPENDIX
：
DIMENSION································································· 38
9APPENDIX
：
PLC I/O ····································································· 39
10 WARRANTY··················································································· 40
4
1 Caution
Info:
【Warning instructions in this manual and on labels are classified as described
below.】
WARNING: This means that possible death or serious
injury to the operator may result if these instruction are
ignored and the equipment is handled incorrectly.
Forbidden: This symbol means that the instruction
describes prohibited item or actions.
ELECTRICAL EQUIPMENT: This symbol means there is
possible serious injury by high voltage。
Heating: This symbol means there is possible serious
injury do to high temperatures.
Info
Ultraviolet radiation warning: This symbol means that
possible serious injury due to Ultraviolet radiation. Wear
safety glasses.
5
1.1 Safety Instruction
Forbidden
Disassembly and modification is prohibited.
Do not touch the display or repair the equipment when something is wrong
with the equipment.
In case of power plug damage, stop using the equipment.
Should an abnormal condition found such as smoking, abnormal smell or
noise, turn off the power immediately and then disconnect the power cable
from the AC outlet.
When internal inspection or repair is needed, contact the selling
agent or Marketing Department of Henkel AG & Co. KGaA.
Warning
Disassembly and modification is prohibited.
Make sure that the power voltage in use complies with specifications.
Disconnect the power supply after finishing working.
Please hold power plug when pulling out the power cable. Don’t hold the
cable, it is possible to be injured by electrical shock.
Do not allow liquid to enter the equipment.
Disconnect the power supply before cleaning the equipment. Do not use an
organic solvent to clean the cabinet.
In the case of an abnormal condition, stop using the equipment immediately.
1.2 Out of Box Inspection
Open Loctite® CL10 Quad LED Controller package carefully and check if
components were damaged during delivery. Please inform carrier if unit is
damaged. Make a claim for damage with the carrier and inform manufacturer
immediately.
Make sure to read these “safety Instructions” carefully before
starting to use the equipment and observe them during operation.
Please familiarize yourself with warning instructions and labels.
6
1.3 Packing list
CL10 Quad LED Controller x1
220V Power Cable x1
97201 Foot Switch x1
Q1 Adapter x1
2 Overview
LoctiteCL10 Quad LED Controller, the UV light source is in accordance with
JIS C6802 “LED Safety Standard”, LED product classifications: 3B, wavelength:
365 or 405nm, meets the requirement of UV curing in Optical, Electronic, Optical
Fiber, communication and printing industry.
Advantage：
1. Long working time, more than 20,000 working hours.
2. Thermal radiation free, low temperature change on irradiated surface,
resolves heat damage issues.
3. Uniform distribution of irradiating.
4. PB free.
5. Low energy consumption, as compared with mercury lamp systems, up
to 90% energy savings.
6. Small and easy to carry and install.
7. Low maintenance cost.
There are 5 production modes integrated in this equipment, C.C mode, OPT
mode, PWM mode, step mode and manual mode. Can meet the
requirements for most industries. Equipment can be connected with up to
four foot switches, or can connect with a PLC I/O, easy to manage the
production line. There is a LED over heating warning inside.
7
3 Technical Data
Type 1514634
C.C. Intensity (0%~100%), Time (0.1~999.9
seconds)
Manual Intensity (0%~100%), Time: Manual control
OPT Lens bonding
STEP 10 steps, each step can define intensity and
time independently.
MODE
PWM Intensity (0~100%) ，Time (Max.999.9
seconds)
Power Supply AC100-220V 50/60Hz MAX 1.5A
Power
consumption 30W
Cooling method Natural air cooling
Temperature
range Operating:+5~+35℃，Storage:-15~+65℃
Humidity Range 20~85%
Cabinet Material aluminum
Quantity 2Kg
Wavelength 365nm, 405nm
8
4 Installation
4.1 Capacity
Power
SET MODE
ESC
START
STOP
CL10 Quad LED Controller
Minimum space required for the equipment.
Please check the unit for any mechanical defects. If there is any breakage
due to delivery, please stop using equipment and return to supplier.
9
4.2 Dimensions
Power
SET MODE
ESC
START
STOP
CL10 Quad LED Controller
AC 100~240 V 50/60Hz MAX 0.6A
FUSE: 3 AMP 240VAC
RS232
CH1
CH2
CH3
CH4
SERVICE
CH1
CH2
CH3
CH4
Item No . 1514634
Input:100~240VAC,50/60 Hz
Rated P ower: 30 W
Henkel Ch ina Company Limited
No.928 Zh angeheng Rd. Pudo ng.
Shanghai . P.R. China 201203
Made In China
SerialNo.
10
4.3 Caution
Set the unit horizontally on a level surface. Failure to do so can cause the
equipment to stop working normally, over heat, or other damage can occur.
Avoid places with high voltage machinery.
Make sure nothing can be placed on power cable, and that it will not be
reachable by the operator.
Keep away from heating sources.
Avoid places with high temperatures or extreme cold.
Allow for adequate ventilation so that exhaust from the heat outlet does not
remain around the equipment.
Info：
● Where there are ventilation holes,
please do not block
● Make sure unit is well ventilated
Otros manuales para CL10
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Controladores de Loctite
Loctite
Loctite 98521 Manual de usuario
Loctite
Loctite 1461974 Manual de usuario
Loctite
Loctite CL10 Manual de usuario
Loctite
Loctite Single CureJet Manual de usuario
Loctite
Loctite EQ CL42 Manual de usuario
Loctite
Loctite 97152 Manual de usuario
Loctite
Loctite 2257357 Manual de usuario
Loctite
Loctite 97102 Manual de usuario
