Lilin IPR424ESX Manual de usuario
IPR434/438ESX
LR7224/7228EX
IPR424/428ESX
D/N 3MP HD Vari-Focal Infrared IP Camera
D/N 1080P HD Vari-Focal Infrared IP Camera
D/N 1080P HD Vari-Focal Infrared IP Camera
66-LR7228CSM
Quick Installation Guide
CAUTION
Do not drop or strike this equipment
Do not install the equipment near any naked flames or heat
sources
Do not expose this unit to rain, moisture, smoke or dust
environment
Do not cover the opening of the cabinet with cloth and plastic
or to install this unit in poor ventilated places. Allow 10cm
between this unit and its surroundings
Do not continue to operate the unit under abnormal conditions
such as detection of smoke, strange smell or no display on
screen while power is turned on
Do not touch the power connection with wet hands
Do not damage the power cord or leave it under pressure
Do not operate this unit near magnet, speaker system, etc., to
avoid unnecessary magnetic interference
onnection cables should be grounded properly
Product Overview
Sun Shield
Top over
Bottom hassis
Bracket
Pan Adjustment Screw
Tilt Adjustment Screw
Lens
Light Sensor
English
Unit: mm
Installation
1. Take out the bracket from the box. Put the power cable and
network cable through the bracket and then fix it to the wall
(FIG.1 & FIG.2).
2. Take out the camera body and open the top cover with screw
driver (FIG.3).
3. Put the power cable and network cable through the bracket
rubber and then pull the cables through the bottom of camera
body (FIG.4). onnect the power cable to the terminal and
connect the network cable to RJ-45 slot of the camera (FIG.5).
English
4. Use the provided 1/4”-20UN screws (4 silver ones) to fix the
camera body on the bracket with hexagon screw driver (FIG.6).
5. Loose the pan and tilt adjustment screws on the bracket to turn
the camera body to the desired angle and then tighten the
screws (FIG.7).
English
6. Adjust the lens on focus and zoom for recording clear video
image. After that, tighten the screws (FIG.8).
7. Replace the top cover and tighten the screws (FIG.9 & FIG.10).
System Overview
Top View
English
Input/Output Device Component Description
Alarm In/Out & Audio In/Out onnector
SD ard onnector
RJ-45 Jack
Video Out Jack
Load Default Button
System Architectures
For connecting HD IP cameras to the network, please follow one of
the system architectures:
(1). Use A 24V or A 100~240V power supply and a network switch
to connect to the network.
(2). Use a PoE+(30W) network switch to connect to the network.
(3). Use a PoE+(30W) power injector and a network switch to
connect to the network.
English
Emergency Factory Default
To restore factory default settings by hardware, please follow these
steps:
1. Hold “RESET Key” for 10 seconds, then release.
2. After about 40 seconds, the network LED light should turn off,
and the back on again.
3. This camera has completed the factory default settings, and can
then reboot.
4. Search for the IP device using the IPScan software.
5. Start the IP device via Internet browser.
6. Enter the default username “admin” and password “pass” to
operate.
NOTE: For user convenience, restoring the factory default settings
will revert to the default IP address 192.168.0.200.
Before Accessing IP Cameras
Before accessing the IP camera, make sure that the camera’s RJ-45
network, audio, and power cables are properly connected. To set the
IP address, consult your network administrator for an available IP
address. The default IP address for each IP camera is 192.168.0.200.
Users can use the default IP address for verifying the camera’s
network connection.
English
Software Requirements
Merit LILIN Universal ActiveX software components are required for
web interface display of JPEG or H.264 Full HD video. When you
login to the IP camera by Internet Explorer, the security warning
dialog box will prompt the installation of the LILIN Universal ActiveX.
lick Install to download it.
Configuring IP Addresses by IPScan Software
To configure an IP address using the IP scan tool, you can copy the
IPScan software from the installation D, and paste to your
computer. Alternatively, you can execute the IPScan software from
the installation D, or download the software from the Merit LILIN
website (www.meritlilin.com). To change the settings of the IP
address, subnet mask, gateway, or HTTP port, you can follow the
steps below:
1. Run the IPScan software.
2. lick Refresh. All available devices should be listed in the device
list.
3. Select your device from the list provided.
4. hange the IP address, subnet mask, gateway, or HTTP port for
the IP camera.
5. lick Apply to submit the settings.
6. lick Refresh to verify the settings.
English
Configuring IP Addresses via Web Interface
To change an IP address via web interface, type the default IP
address (192.168.0.200) in the Internet browser and follow the steps
below:
1. Login to the H.264 Full HD IP camera by the default username
“admin” and default password “pass”
2. lick asic Mode configuration hyperlink.
3. lick Network->General hyperlink.
4. hange the IP address, subnet mask, gateway, or HTTP port for
the IP camera.
5. lick Submit to verify the settings.
English
Este manual sirve para los siguientes modelos
5
Tabla de contenidos
Otros manuales de Cámara de seguridad de Lilin
Lilin
Lilin IPS 8264 Manual de usuario
Lilin
Lilin PIH - 7000 Manual de usuario
Lilin
Lilin CMR7082N/P3.6 Manual de usuario
Lilin
Lilin LR7228EX Manual de usuario
Lilin
Lilin IPD2322ESX Manual de usuario
Lilin
Lilin AHD705A3.6 Manual de usuario
Lilin
Lilin ST1358 series Manual de usuario
Lilin
Lilin CMG052X35 Manual de usuario
Lilin
Lilin PSR5024EX20 Manual de usuario
Lilin
Lilin Z2R8122X-P Manual de usuario
Lilin
Lilin PIH-7635DH Series Manual de usuario
Lilin
Lilin Z2R8852AX Manual de usuario
Lilin
Lilin Z2R8852AXK Manual de usuario
Lilin
Lilin PIH-2522 Manual de usuario
Lilin
Lilin IPD552EX4.2 N Manual de usuario
Lilin
Lilin MR8322 Manual de usuario
Lilin
Lilin CMD6182X Manual de usuario
Lilin
Lilin PIH-0746XW Manual de usuario
Lilin
Lilin IPC0522 Manual de usuario
Lilin
Lilin PSD4624EX20 Manual de usuario
