Lennox HYDROCONTROL Manual de usuario

-0-HYDROCTROL-IOM-1903-E

CHILLERANDFANCOILCONTROL

HYDROCONTROL

HYDROCONTROL-IOM-1903-E

-1-HYDROCTROL-IOM-1903-E

-2-HYDROCTROL-IOM-1903-E

TABLE OF CONTENTS

HYDROCONTROL

INTRODUCTION

TECHNICAL SPECIFICATIONS

Technical features

INSTALLATION

Dimensions & weight

Compatibility

Opening the HMI

Fastening

Installation, operating

and maintenance

Ref : HYDROCONTROL-IOM-1804-E

Wirings 8

Software installation

OPERATING

Fan Coils settings

HMI settings

Password management

Chiller screens 23

Fan coil screens 24

Schedule management 27

Multi temp view

HYDROCONTROL Home page 17

Set the fan coil using the HMI 29

Connect the HMI using a browser

HYDROCONTROL Start up

Diagnostics 30

Chiller parameter (Climatic™)

APPENDIX 31

Screen list

DIP Switch Position 32

-3-HYDROCTROL-IOM-1903-E

INTRODUCTION

Safety codes &regulations

THE DISPLAY MUST BE INSTALLED IN ACCORDANCE WITH LOCAL SAFETY CODES AND REGULATIONS.

PLEASE READ CAREFULLY THE MANUFACTURER’S INSTRUCTIONS BEFORE STARTING THIS DISPLAY.

Version concerned

The following manual is only valid for version higher or equal to 11.7 of LennoxHydrocontrol display. In case of Chiller connected to

the LennoxHydrocontrol the version of Chiller control must be higher than Ch60 v2r3.3 or eCH v0r2.2

WARNING - All the technical and technological information contained in this manual, including any drawing and technical descriptions

provided by us, remain the property of LENNOX and must not be utilised (except in operation of this product),reproduced, issued to or

made available to third parties without the prior written agreement of LENNOX. The technical information and specifications contained

in this manual are for reference only. The manufacturer reserves the right to modify these without warning and without obligation to

modify equipment alreadysold.

WARRANTY

The warranty of the display is subject to the warranty definitionsas agreed upon in the order.

It is expected that the design and installation of the display utilises good working practices.

The warranty will be legally null and void if:

•Modifications have been made to the equipment without prior written permission by LENNOX.

•Settings and protections have been modified without prior written permission by LENNOX.

•The equipment has not been installed and/or connected in accordance with the installation instructions.

•The equipment is being used improperly,incorrectly, negligently or not in accordance with its nature and/or purpose.

In these circumstances LENNOX is indemnified from any product liability claims from third parties.

Abbreviations

The following abbreviations are used in this document

. HMI = LennoxHydrocontrol display

. FCU = FanCoil units

-4-HYDROCTROL-IOM-1903-E

TECHNICAL SPECIFICATIONS

Technical features

The HMI is a touch-sensitive screen LCD display. It is managing up to 32 FCU. This display can also be connected to 1 Chiller

which allows to managed the working mode changeover and the water temperature. The HMI is able to control up to 9 different

schedules.

Six languages are supported by the HMI

- English

- French

- Italian

- Spanish

- German

- Portuguese

The HMI uses 24Vac 50/60Hz power supply. In case of power failure the HMI will use its supercapacitor for internal memory.

2 entire days are necessary to fully charge the supercapacitor

The HMI is compatible with the LENNOX Chillers with a version higher than Ch60 v2r3.3 or eCH v0r2.2 and the FCU mounted with

the CTRL2303D4A-BDC controller. It can be used even if the FCU already have a connected thermostat.

Dimensions & weight

The following table indicates the dimensions and the weight of the HMI:

Device Height

(mm) Width

(mm) Thickness

(mm) Weight (g)

HMI 142 208 35 460

Compatibility

The HMI offers a web access via an Ethernet connection using a web browser.

The connection between HMI and FCU uses the MS/TP BACnet protocol.

The HMI can be connected to the FCU even if a thermostats is already connected.

-5-HYDROCTROL-IOM-1903-E

INSTALLATION

Fastening

The HMI is a wall mounted display. To fasten the HMI on a wall we recommend to use the dedicated holes at the back of the

device.

There are two possibilities to fasten the HMI.

1. Partially build in the wall

Cut a hole into the surface

Mount the HMI using the 4 outside mounting holes

Opening the HMI

To access the wiring and fixing area you have to open the HMI on the top of the device and spin the screen. /!\ The display is

screwed to the black case.

Picture1: Top view of the Hydroctonrol

Picture2: Hydrocontrol schematic (Partially build in wall)

-6-HYDROCTROL-IOM-1903-E

INSTALLATION

Wirings

Two different connections are necessary. But some other can be added in case of option

1. Power supply connection

The 24Vac 50/60 Hz power supply is required and has to be connected in the following pins: See picture index 1

2. BACnet MS/TP connection

Connect the BACnet MS/TP network to the dedicated pins. We recommend to use shielded twisted pair cable. The daisy-

chain connection is required. (star and ring connections are forbidden): See picture index 2

Chiller connection (Option)

In case the HMI is also connected to the Lennox chiller, The BACnet MS/TP communication card (S/n: (EL)4770643E) is

required on the controller of the chiller.

3. Ethernet connection (Option)

The HMI offers the possibility to be a web server. This means the display is also accessible via internet. You can connect

the HMI to your network using the RJ45 cable. See picture index 3

2. On a wall

Place the HMI on the wall and mark at least 4 points for screws and the hole for electrical wirings

Cut the hole for wiring and drill screw holes

Mount the HMI on the surface

Picture3: Hydrocontrol schematic (On a wall)

Picture4: Hydrocontrol main board

-7-HYDROCTROL-IOM-1903-E

INSTALLATION

Other devices

•HMI at the end of daisy-chain connection:

Set the jumper of the MS/TP communication card according the following:

•HMI in the middle of daisy-chain connection:

Set the jumper of MS/TP communication card according the following:

Other devices

Picture6: BACnet MS/TP wiring example (HMI in middle of the line)

Picture5: BACnet MS/TP wiring example (HMI in middle of the line)

-8-HYDROCTROL-IOM-1903-E

INSTALLATION

Software installation

The HMI is supply without the HYDROCONTROL application loaded inside it.To load the application you must use one USB flash

drive with the both files (ask them to a LENNOX technician):

•Lennox Suite V11_7.PDB (You have to use at least the version 11.7)

•eTCH_V340_B-3935.FLS

Then insert the flash drive in one of the USB connectors of the HMI and power the display. The following display will appear:

Press “Oui”(yes) and the installation will start and the next screen will appear:

Wait the end of the installation

Once it is done please remove the flash drive and the HMI will restart automatically

Picture8: Update home screen

Picture9: Update progression

Picture10: Update finished

Picture7: USB port for software update

-9-HYDROCTROL-IOM-1903-E

OPERATING

Fan coil settings

To make the FCU communicating with the Hydrocontrol and working accordingly your requests you will have to set them with the

EC-Smart_Vue thermostat.

Connect the thermostat to the FCU controller using a RJ45 cable

To access all the parameters, from the home screen press the menu button for 5 seconds.

Use the arrows to set the password to 9995

You will then access the different setting menu. Use the button menu to choose the submenu you want to go and use one of both

arrow to enter inside the submenu. Once you are inside the submenu you the button menu to choose the parameter you want to set

and use the arrow to change the value. Once the value is set use the button menu to go to “Exit” and press an arrow to validate and

come back to the submenu selection

Home scrren

Password

Submenu 1

Setting 1

Setting 2

Setting n

Exit

Submenu 2

Setting 1

Setting 2

Setting n

Exit

Submenu n

Setting 1

Setting 2

Setting n

Exit

Picture11:EC-Smart-Vue / CTRL2303D4A-BDC

EC-Smart-Vue

FCU Controller:

CTRL2303D4A-BDC

Tabla de contenidos

Otros manuales de Controladores de Lennox

Lennox

Lennox DC 60 Manual de usuario

Lennox

Lennox LXTFF01M Manual de usuario

Lennox

Lennox CLIMATIC series Manual de usuario

Lennox

Lennox M0STAT120N-1 Manual de usuario

Lennox

Lennox icomfort Wi-Fi (2.0) Demo Manual de usuario

Lennox

Lennox F1943L-3P Manual de usuario

Lennox

Lennox V0STAT52 Manual de usuario

Lennox

Lennox e-Lite LV-CW02 Manual de usuario

Lennox

Lennox M0STAT64Q-2 Instrucciones de instalación

Lennox

Lennox NTC1-1-Kit Manual de usuario

Lennox

Lennox V0STAT51P-2 Manual de usuario

Lennox

Lennox VRF F1943L-3P Instrucciones de instalación

Lennox

Lennox V0STAT54P-2 Instrucciones de instalación

Lennox

Lennox M0STAT120L-1 Manual de usuario

Lennox

Lennox PRODIGY2.0 Guía del usuario

Lennox

Lennox M0STAT61Q-1 Instrucciones de instalación

Lennox

Lennox @DNOVA 2mAC ADVANCED CONTROLLER Manual de usuario

Lennox

Lennox 22U50 Manual de usuario

Lennox

Lennox VRF VEWCL1B Manual de usuario

Lennox

Lennox @DNOVA pCO1 Manual de usuario

Lennox

Lennox Prodigy Manual de usuario

Lennox

Lennox E210 Manual de instrucciones

Lennox

Lennox PRODIGY M2 Manual de usuario

Lennox

Lennox V0STAT51P-3 Instrucciones de instalación

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario