Leica DISTO D410 Instrucciones de funcionamiento

How to use Leica DISTO™ D410

Switch On and Off

The key switches and activates the laser in a single press.

Press once quickly to shoot a distance or...

Press and hold for 2 seconds to activate continuous laser

measurement (Tracking).

Press once quickly to switch off tracking.

Press and hold the button for 2 seconds to switch off the

410. The 410 automatically switches off after 3 minutes of

inactivity.

Display Overview of the Settings Page page

Display Overview of the Functions Page

Basic Operations

Beep On/Off

Turn the beep on/off as per your convenience.

Press the key once to reach the application screen.

Select the settings option from this screen by pressing the soft key

underneath the icon .

On this screen, **Beep on/off icon / is located at the top right

of the display.

Navigate to the icon using keys to select for Beep on/off. Select

the icon using = key.

Also toggle between & with = key.

* Press to exit settings.

(**selection screen example for reference)

Display light/screen brightness

Adjust the screen brightness as required.

Press the key once to reach the application screen.

Select the settings option from this screen by pressing the soft key

underneath the icon .

On this screen, (brightness adjustment) illumination icon is

located at the the bottom right of the display.

Navigate to the icon using keys to select for brightness

adjustment.

Select the icon using = key.

Once selected, use the arrow keys to increase or decrease the

brightness from the provided 6 levels.

* Press to exit settings.

Activate/de-activate keypad lock

Press the key once to reach the application screen.

Select the settings option from this screen by pressing the soft key

underneath the icon .

On this screen, the lock icon / is located at the centre of the

display.

Navigate to the icon using keys to select for keypad lock on/off.

Select the icon by pressing =key.

Toggle between / with =key.

* Press to exit settings.

How to unlock keypad

Once the keypad lock system is activated, the device when switched on needs to be

unlocked within 2 seconds after switching it on, or it will automatically switch off.

Press the key within 2 seconds of switching on the device to

unlock the key pad (as it will indicate on the display).

Memory

The device stores last 30 results by default.

To view the results stored in the memory, press the key once.

Navigate to the memory icon with keys, which is located on the centre left of

the display.

Select this icon using = key.

Use navigation keys to view multiple stored results.

Press the soft keys underneath icons & for deleting memory and using

the displyed value for further actions respectively.

Timer (Self trigger) or Auto release

Timer is used for self triggering the measuremnt once the laser is activated. The delayed

release is recommended for precise aiming, e.g. for long distances, as it avoids shaking of

the device while pressing the measurement key.

To set the Timer, press the key once.

Navigate to the Timer icon with keys, which is located at the top left of the

display.

On Timer selection, you reach the screen displayed as

Select the time from the provided options with the help of navigation keys.

To confirm setting press = key.

Press key once to aim the laser.

Press key again to start the timer.

Reset

Reset setting returns the device to its factory settings. All customization and stored

memory is lost.

Press the key once to reach the application screen.

Select the settings option from this screen by pressing the soft key underneath

the icon .

Move to the 2nd page of the settings with the help of keys.

On this screen, reset setting icon is loacted at the top centre of the display.

Navigate to the icon using keys to select for reset setting. Select the icon using =

key.

Use soft keys under or Xto confirm reset or cancel respectively.

Offset

Offset setting allows you to add or subtract a set value automatically to or from all

measurements.

Press the key once to reach the application screen.

Select the settings option from this screen by pressing the soft key underneath

the icon .

Move to the 2nd page of the settings with the help of keys.

On this screen, Offset setting icon is located at the top left of the display.

Navigate to icon using keys to select for offset setting. Select the icon using

=key.

Use & keys to adjust the value.

Use soft key under icon to confirm or…

Reset the value to 0.00

Advance operations

Personalized favourites

Press the key once to reach the application screen.

Select the Settings option from this screen by pressing the soft key

underneath the icon .

On this screen, Personalized favourites (a star shaped icon) is

loacted at the bottom centre of the display.

Navigate to the icon using keys, to select for Personalized

favourite. Select the icon using =keys.

Select your favourite functions and add them to your personal list.

Changing distance Units

Leica Disto X410 is provided with the stock of units that you can change as per your

requirement. Change from meter to feet to inches, per your convenience.

Press the key once and you reach the application screen.

Select the Settings option from this screen by pressing the soft key

underneath the icon .

On this screen, Distance Units icon is located at the top center of

the display.

Navigate to the icon using keys to select for Distance Units.

Select the icon using =key.

Choose from the below listed units keys.

0.00 m 0.00 ft

0.000 m 0.00 in

0.0000 m 01/32 in

0.0 mm 0’ 00” 1/32

Adjusting measuring reference/tripod

Custom your D410 to measure the distance from its front, rear, middle or the tripod

thread of the device.

1. Each time the device is switched on, the display shows the default or the standard

mode as which means that the distance is being measured from the back of the

device .

You can further change the settings by pressing under the screen to adjust the

mode to either

2. - Measurement from the Leica Disto Adapter FTA 360.

3. - Measurement from the front of the device,

- Lock icon = permanently

4. - Measurement from the tripod thread of the device.

How to adjust the measuring reference

Press the key once to reach the application screen.

Select the Adjust measurement application from the top right

section by pressing .

Select the icon using =key.

Choose from provided:

from the front,

back,

middle or

tripod thread of the device.

* Once the device is switched off, reference goes back to standard setting (i.e. rear of the

device)

Adjusting/Standardising/Calibration of tilt sensor (Tilt

Calibration)

Press the key once to reach the application screen.

Select the Settings option from this screen by pressing the soft key

underneath the icon .

On this screen, Tilt calibration icon is located at the bottom left of

the display.

Navigate to the icon using keys to select for Tilt calibration.

Select the icon using =key.

* Press to exit settings.

(Also)

Follow these quick 6 steps to adjust or calibrate your device in case of an unlikely

discrepancy.

As indicated on the device display:

Place the device on an absolute flat surface with its display up and press .

Next rotate it by 180° and place the device on the surface as it was and press again.

Next stand the device up on a horizontal surface and press .

As indicated rotate the device 18o°in its vertical position and press again.

Next place the device upside down as shown in the picture on the left and press .

Rotate the device again by 180° and place it on the surface and press .

*The device calibration is complete.

Basic device Applications

Straight line single distance measurement

Basic usage is quite simple.

To begin, press the key once to switch the laser on and aim at

your target.

Pressing again records the measurement and shows the result

on the device display.



* For measurements, where there is nothing obvious at the other end for the laser to reflect back, it is

recommended that you use Leica branded Target plate for maximum measurement range.

Permanent / Minimum-Maximum measurement

This function determines the minimum or maximum distance from a specific measuring

point, e.g. the determination of room diagonals (maximum value) or horizontal distance

(minimum value).

To activate permanent measuring, press and hold the key for 2

seconds. This will activate the continuous laser.

Aim the laser at wall corners (maximum value) or horizontal distance

(minimum value). The display would show the max. & min. values on

the screen.

To stop permanent/minimum-maximum measuring press key

once.

Add/ Subtract function

Add / Subtract are two basic functions in D410. The keys are

displayed on the device for this application.

Press once to add the next measurement to previous one.

Press twice to subtract the next measurement to previous one.

Point finder/View screen

Press the key on the device to activate the camera mode.

With the help of navigation keys zoom the pointfinder to 1x, 2x &

4x zoom.

*You can also adjust the illumination by using keys.

Area Measurement

Area measurement is a basic function provided in all Leica Disto devices. This helps you

calculate the area of wall or surface just by measuring its sides from the same reference

point.

For measuring the area of a surface, press the Function key once.

On this screen, the area application is located at the center of

the display.

*In D410, you can also find the area application at the bottom left of the device

as you switch it on.

Navigate to the icon using keys to select for Area

application. Select the icon using =key.

To begin, press the key once to switch the laser on and aim at

your target to take the 1st reading.

Then focusing from the same reference point take the 2nd reading by

measuring the adjacent wall length. (as the area icon will indicate on

display)

Once this process is completed the device automatically calculates

the area for you.

* Adding and subtracting areas

You can measure two separate areas and add or subtract them from each other with the

help of or keys.

**The device also calculates

The total linear distance or the circumference.

Volume Measurement

For measuring the volume of an object press the Function key

once.

On this screen, volume application is located at the bottom right

of the display.

Navigate to the icon using keys to select for Volume

application. Select the icon using =key.

Measure the three adjacent lengths (l x b x h) using . (as the volume

icon will indicate on display)

*All measurement needs to be taken from the same reference point.

Once this process is completed the device automatically calculates

the volume on the display.

*The device also calculates:

Ceiling/floor area

Wall areas

Total linear distance (circumference)

Smart Horizontal Mode™

A wonderful application to measure the horizontal distance even with an obstruction in the

way.

For measuring the distance from an object through Smart Horizontal

Mode™, press the Function key once.

On this screen, Smart Horizontal application icon is located at

the middle right of the display.

Navigate to the icon using keys to select for Smart Horizontal

application. Select the icon using =key.

Aim the laser at an angle of a certain tilt and record the measurement

by pressing .

The device automatically calculates the horizontal distance from the

target.

*Along with the horizontal distance this application also records:

angle of the tilt

length of the tilt and

the vertical height from the device.

2 point indirect horizontal length measurement

This function helps you measure the length of an object indirectly just by focusing on 2

points.

Press the Function key ocne.

Move to the second page of the application screen using keys.

On this screen, 2 point indirect length measurement application

icon is located at the bottom centre of the display.

Navigate to the icon using keys to select the option for 2 point

indirect measurement. Select the icon using =key.

To measure the horizontal length through this application, measure

points a. & b. from the same reference point.

How to measure a. & b.

Aim the laser at point a. and record that measurement by pressing

Next aim the laser at point b. as shown in the figure on the left and

record that measurement by pressing again

The device automatically calculates the distance from a. to b.

The device also calculates the distance from the device to points a. &

*This application requires tripod.

** This application is applicable only to measure the horizontal length. To measure the vertical height

please use the Height Tracking function.

Otros manuales para DISTO D410

Tabla de contenidos

Otros manuales de Instrumento de medición de Leica

Leica

Leica Lino L2P5 Manual de usuario

Leica

Leica Racer 100 Manual de usuario

Leica

Leica DISTO S910 Manual de instrucciones

Leica

Leica RANGEMASTER 1200 scan Manual de usuario

Leica

Leica TS13 Manual de usuario

Leica

Leica TS12 Lite Manual de usuario

Leica

Leica TS01 Manual de usuario

Leica

Leica Rugby 55 Manual de usuario

Leica

Leica Rod Eye 160 Manual de usuario

Leica

Leica Viva TS16 Manual de usuario

Leica

Leica Nova MS60 Manual de usuario

Leica

Leica LINO L6R Manual de usuario

Leica

Leica RTC360 Manual de usuario

Leica

Leica Rugby 640G Manual de usuario

Leica

Leica TS11 Manual de usuario

Leica

Leica DNA03 Manual de usuario

Leica

Leica 3D Disto Manual de usuario

Leica

Leica Lino L2 Manual de usuario

Leica

Leica TPS1200+ Series Manual de usuario

Leica

Leica iCON PA10 Manual de usuario

Leica

Leica GLOW800 Manual de usuario

Leica

Leica ScanStation P50 Manual de usuario

Leica

Leica MOJO RTK Guía del administrador

Leica

Leica NA520 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario