LEGRAND HKRL20 Manual de usuario
installation guide
Smart Remote Switch
Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HKRL20
2
table of contents
before you start..................................3
what you need ...................................4
getting to know your remote switch
........................................................6-7
installation and setup ................ 8–22
faqs ..............................................23
regulatory information ......... 24–27
warranty.......................................28
support ........................................29
3
before you start
Review this guide in its entirety before beginning device installation. Consult an
electrician with any questions or if you are unsure of your abilities.
DWarning: Incorrect installation could
result in death, serious injury, and/or
damage to your home or devices:
• For dry, indoor use only.
• Connect the smart remote switch to a
120 VAC, 60 Hz power source ONLY.
• The remote switch pairs ONLY with
the smart switch (HKRL10) for multi-
location control.
• The remote device does NOT connect to
any lighting loads. It is powered by your
electrical wiring and uses a wireless
connection to control its paired devices.
• Always use copper wire to install the
smart remote switch and follow all
applicable local and national electrical
codes.
• Install in a non-metallic electrical box
to protect wireless signal strength.
Visit the Legrand website at www.legrand.us/radiant/homekit.aspx to learn more about
your smart device.
4
what you need
REQUIRED:
Phillips-head screwdriver
Flat blade screwdriver
YOU MAY ALSO NEED:
Non-contact voltage tester, pliers, wire cutter, wire stripper, electrical tape,
flashlight, radiant®screwless wallplate (included), wiring leads (included), and
wire nuts (included)
NOTE: Exercise caution when using power tools. Overtightening the screws can
damage the device.
5
6
getting to know your remote switch
Item Name Description
1 Paddle Switch
• Press the top of the paddle to turn the light on and
the bottom to turn the light off.
• To return the switch to factory default, press and
hold the top of the paddle for 15 seconds. Then,
remove the device from the Legrand Home app (or
Apple Home app).
2 LED Locator Light Indicates the current state of the device. Refer to
“LED Locator Light Explanations” for detail.
7
1
2
LED LOCATOR LIGHT EXPLANATIONS
LED
Color State of Light Explanation
Slowly Flashing
Amber
Device is attempting to connect to
the network
Solid White Connected to Wi-Fi and turned off
No Light Device is on
Rapidly Flashing
Green
N-Way Pairing mode: device is
attempting to pair with the master
Rapidly Flashing
Amber N-Way pairing is updating
Solid Amber N-Way pairing is successful
8
installation & setup
step one
|
turn off power for your device at the
circuit breaker
Flip the existing light switch multiple times to confirm the power is off.
NOTES:
• If there are multiple devices next to your existing light switch, make sure power is
off at the circuit breaker for all of those devices.
• If you are installing your master device at the same time as the remote device,
make sure power is off to both devices.
• For detailed instructions on how to install your three-way remote product, please
visit legrand.us/3wayinstallationinstructions.
9
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
10
installation & setup
step two
|
remove the existing device
Check for the following wires:
1HOT or LINE: Receives power from the circuit box. Referred to as “hot” for the
purposes of this guide. Do not touch or let “hot” wires contact other wires.
2LOAD: Directs power to your light(s).
3NEUTRAL: Creates a path to return current to the power source, when the
device is off. Required for your switch installation.
4GROUND: Provides a safe path for electricity in the event of a short circuit.
5TRAVELER: Connects power between the three-way wiring devices. Not required for
your switch installation. Cap all traveler wires.
NOTE: Refer to the “faqs” on page23 if you are unsure of your wiring.
Tabla de contenidos
Otros manuales de Cambiar de LEGRAND
LEGRAND
LEGRAND PRO 21 7756 36 Manual de usuario
LEGRAND
LEGRAND Pass & Seymour OSR300S Manual de usuario
LEGRAND
LEGRAND PRO 21 7756 27 Manual de usuario
LEGRAND
LEGRAND DMX Manual de usuario
LEGRAND
LEGRAND 6058 51 Manual de usuario
LEGRAND
LEGRAND HKRL10 Manual de usuario
LEGRAND
LEGRAND Mosaic 0 777 06LA Manual de usuario
LEGRAND
LEGRAND radiant LC2201 Manual de usuario
LEGRAND
LEGRAND 0 672 27 Manual de usuario
LEGRAND
LEGRAND 34061 Manual de usuario
LEGRAND
LEGRAND adorne ADWR600RMH Manual de usuario
LEGRAND
LEGRAND 5 745 03 Manual de usuario
LEGRAND
LEGRAND 0 672 23 Manual de usuario
LEGRAND
LEGRAND 916 30 Manual de usuario
LEGRAND
LEGRAND PRO 21 7756 32 Manual de usuario
LEGRAND
LEGRAND 5 742 02 Manual de usuario
LEGRAND
LEGRAND Pro 21 7756 44 Manual de usuario
LEGRAND
LEGRAND Valena Life 7 521 90 Manual de usuario
LEGRAND
LEGRAND MICROREX D11 Manual de usuario
LEGRAND
LEGRAND PX3 Manual de usuario
