LEGRAND WIREMOLD RFB2 Manual de usuario

RFB2, RFB2-SS, RFB2-OG

Recessed Floor Box

INSTALLATION INSTRUCTIONS

Installation Instruction No.: 1 006 179 – September 2006

Wiremold / Legrand electrical systems conform to and should be

properly grounded in compliance with requirements of the current

National Electrical Code or codes administered by local authorities.

All electrical products may present a possible shock or fire

hazard if improperly installed or used. Wiremold / Legrand electrical

products may bear the mark as UL Listed and/or Classified and should

be installed in conformance with current local and/or the National

Electrical Code.

IMPORTANT: Please read all instructions

before beginning.

BEFORE CONCRETE POUR:

NOTE: Box is supplied with tunnel bracket, tunnel blocks

and device mounting brackets installed. If the

same service is to be used in both compartments,

it will be necessary to remove one or both of the

tunnel blocks to allow for pass-through of the

service wiring. The tunnel blocks are accessible

by removing the tunnel support. The installer may

do this either pre- or post-pour.

Step 1. Determine box location and conduit layout. Remove

box cover and desired knockouts and attach

appropriate conduit adapters, (not supplied by

Wiremold) to steel base.

Step 2. Re-attach box cover to base with (2) #8-32 x 1/2" long

screws provided.

Step 3. Adjust height of box so that the top of the black

trim ring is approximately 1/16" below the concrete

screed line.

Step 4. Secure the box to the floor using wire or other

fasteners through the holes provided in the top

cover. Once positioned, connect conduit to adapters

previously attached to box.

Step 5. Insert mud cap into top opening and press down

firmly to secure. Box is now ready for pour.

WARNING: Pour concrete to 1/16” (1.6 mm) above box

housing. Pours of 1/4” (6.4 mm) or more

over box housing will make it difficult to

break out the mud cap and cause excessive

concrete spalling.

Tunnel Blocks

Tunnel Support

Top of Plastic

Trim Ring

Adjusting

Screws

This box and activations are UL listed for use with tile, terazzo, carpet covered concrete

floors, and floors of wood construction.

AFTER CONCRETE POUR:

NOTE: This box and activation are UL Listed for use with

tile, terrazzo, and carpet covered concrete floors,

and also wood floors.

NOTE: Use insulator provided with the following catalog

numbers, installed as shown: RFB2DP, RFB2GFI.

Step 6. Locate box and chip away concrete located in mud

cap. Remove mud cap, and clean out any debris from

inside of box. If concrete does not break cleanly around

preset, the activation might not be properly supported.

The concrete edges around the top opening of the

installed box must be smooth and level for the proper

fit of the FloorPort Activations. Remove device

brackets, and the tunnel block(s) if required to provide

for the same service in both compartments. To access

the tunnel blocks, remove the tunnel support and then

re-install after removing the required block(s).

Step 7. Wire devices (not supplied by Wiremold), making sure

that any ground leads are properly connected to

ground screws. Attach the receptacle to the receptacle

mounting bracket using the #6-32 screw provided.

Secure the receptacle to the receptacle mounting

bracket with (2) additional screws and nuts, (not

provided). Attach the receptacle mounting bracket(s) to

the base with the (2) #8-32 mounting screws provided.

Step 8. Complete procedure by installing a Wiremold FloorPort

Activation, (sold separately), using the installation

instructions provided with that unit.

WOOD FLOOR INSTALLATION:

Step 1. Determine box location and orientation.

Step 2. Cut a 6" [152mm] x 7 1/4" [184mm] opening in

wood floor.

Step 3. Remove box cover and desired knockouts. Attach

appropriate connectors per wiring type (mc cable,

conduit, nonmetallic, sheathed, etc., not supplied

by Wiremold) to steel base. Remove tunnel block(s)

as required if power is to be used on both sides of

the box.

Step 4. Re-attach cover to box with two (2) #8-32 x 1/2" long

screws provided.

Step 5. Align plastic trim ring on top of box with opening in

floor, and secure box to underside of floor with four (4)

#8 or four (4) #10 pan head sheet metal screws, (not

supplied by Wiremold), through the four (4) holes

provided in cover.

Step 6. Wire devices, (not supplied by Wiremold), making sure

that any ground leads are properly connected to

ground screws. Attach the receptacle to the

receptacle mounting bracket using the #6-32 screw

provided. Secure the receptacle to the receptacle

mounting bracket with two (2) additional screws and

nuts, (not provided). Attach the receptacle mounting

bracket(s) to the base with the two (2) #8-32 mounting

screws provided.

Step 7. Complete procedure by installing a Wiremold

FloorPort Activation, (sold separately), using the

installation instructions provided with that unit.

NOTE: Box is supplied with tunnel bracket, tunnel blocks

and device mounting brackets installed. If the

same service is to be used in both compartments,

it will be necessary to remove one or both of the

tunnel blocks to allow for pass through of the

service wiring. The tunnel blocks are accessible by

removing the tunnel support. The installer may do

this either pre- or post-installation.

NOTE: Use insulator provided with the following catalog

numbers, installed as shown: RFB2DP, RFB2GFI.

Tunnel Blocks

Tunnel Support

Wiremold / Legrand

U.S. and International:

60 Woodlawn Street • West Hartford, CT 06110

1-800-621-0049 • FAX 860-232-2062 • Outside U.S.: 860-233-6251

Canada:

570 Applewood Crescent • Vaughan, Ontario L4K 4B4

1-800-723-5175 • FAX 905-738-9721

1 006 179 0906

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Rack y soporte de LEGRAND

LEGRAND

LEGRAND SANUS WSSE31 Manual de usuario

LEGRAND

LEGRAND CHIEF ConferenceSHOT PAC800K Manual de usuario

LEGRAND

LEGRAND PX2 Manual de usuario

LEGRAND

LEGRAND CHIEF ODA330 Manual de usuario

LEGRAND

LEGRAND Chief PAC811 Manual de usuario

LEGRAND

LEGRAND CHIEF 25-PTS-2000 Series Manual de usuario

LEGRAND

LEGRAND SANUS WSSE1A1 Manual de usuario

LEGRAND

LEGRAND SANUS ACCENTS ARTVF1 Manual de usuario

LEGRAND

LEGRAND Sanus WSWME31 Manual de usuario

LEGRAND

LEGRAND VADDIO 535-2000-280 Manual de usuario

LEGRAND

LEGRAND Chief TILD1X05US Manual de usuario

LEGRAND

LEGRAND SANUS WSSE3A1 Manual de usuario

LEGRAND

LEGRAND CHIEF KITXWXSM1U Manual de usuario

LEGRAND

LEGRAND CP330017 Manual de usuario

LEGRAND

LEGRAND Sanus VDSF16 Manual de usuario

LEGRAND

LEGRAND CHIEF CSSMP15X10 Manual de usuario

LEGRAND

LEGRAND CHIEF UU Series Manual de usuario

LEGRAND

LEGRAND CHIEF Fusion FCA801 Manual de usuario

LEGRAND

LEGRAND SANUS ELITE BSWME2 Manual de usuario

LEGRAND

LEGRAND CHIEF Fusion FCALRB1 Manual de usuario

LEGRAND

LEGRAND CHIEF HTSTS Manual de usuario

LEGRAND

LEGRAND Sanus VDMF20 Manual de usuario

LEGRAND

LEGRAND CHIEF IntelliSHOT PAC800E Manual de usuario

LEGRAND

LEGRAND Chief Koncis D1U Manual de usuario

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario