LaserLiner TITANIUM Manual de usuario

Titanium

8.045.96.01.1 (8.045.96.02.1) / Rev 07.07

DBedienungsanleitung

Operating instructions

3-14

15-26

27-38

39-50

51-62

63-74

75-86

Titanium

ENGLISH 15

Professional rotary laser of extremely rugged design. Horizontal

and vertical levelling even under the toughest conditions

Automatic self-levelling through electronic vials and servomotors assisted by

temperature stable sensors, horizontal and vertical. This unit is equipped with

all important laser functions and due to the extreme rugged housing works

reliable even under toughest conditions. Dust- and waterproof IP66, preci-

sion 1 mm / 10 m, self-levelling range 5 °. Horizontal slopes can be adjusted.

The included remote control can control all functions. Titanium Red Laser

Class 2.

The green laser of the Titanium Green is much more visible than the red. This

allows applications over longer distances and working under very bright

ambient light conditions. Titanium Green Laser Class 3R.

General safety instructions

Caution: Do not look directly into the beam. Lasers must be kept out of

reach of children. Never intentionally aim the

device at people. This is a quality laser measuring

device and is 100% factory adjusted within the

stated tolerance. For reasons of product liability,

we must also draw your attention to the following: Regularly check the cali-

bration before use, after transport and after extended periods of storage. We

also wish to point out that absolute calibration is only possible in a specialist

workshop. Calibration by yourself is only approximate and the accuracy of

the calibration will depend on the care with which you proceed.

Warranty

The warranty period is 2 years from the date of purchase. The warranty

covers all material or manufacturing defects occurring during this time. The

following are excluded from warranty: Damage due to improper use (e.g.

operation with wrong type of current/voltage, connection to unsuitable

power source, fall onto hard surface, etc.) or improper storage, normal wear

and tear, and defects which only insignificantly impair the value or suitability

for use. Any tampering by unauthorised persons will render this warranty

void. In the event that you need to claim warranty, please take the complete

device together with all information and the invoice to one of our dealers or

send it in to Umarex-Laserliner.



Note:

This product is a precision instrument that must be handled and treated

with care. Avoid shocks and impact. Always keep and carry in the case!

Switch laser off. For cleaning, use a soft cloth and glass cleaner.

Laser light !

Do not stare into the

beam or view directly

with magnifiers.

Class 3R laser

EN60825-1:2003-10

Titanium

ENGLISH

Sensor Automatic

The Titanium is of the self-levelling kind. After it has been put in the required

basic position, fine adjustment is being effected automatically. Horizontal and

vertical orthogonal adjustments are effected by the self-levelling system (SLS),

while the X-, Y- and the Y-axis are scanned by two electronic measuring sen-

sors. The working angle is ± 5°.

Anti-Drift-System (ADS)

The Anti-drift system (ADS) prevents mismeasurements. Its principle of func-

tion: 30 seconds after ADS has been activated, the laser is permanently being

checked for its correct adjustment. In case the instrument has been moved by

external influences or the laser has lost its frequency, the system switches

itself automatically off and the "tilt"-LED shows a permanent light. After the

instrument has been switched on, the ADS is not active. In order to protect

the instrument from position changes caused by external influences, the ADS

has to be activated by pressing the push-button "tilt"(J). Should the instru-

ment be moved by external influences, then the laser is switched off and the

"tilt"-LED (K) shows a permanent light. The instrument has to be switched

off and -on again if work is to be commenced. This is a simple and reliable

prevention of misreadings.

The laser switches

itself off for safety

reasons, the "tilt"-

LED shows a ON

permanent light.

External

influence

Adjustment phase

Sensor Automatic

Acticate ADS:

Press “tilt” but-

ton (D), long

blink signals in

tilt display (K).

after 10 sec.,

short blink signals

in tilt display (K).

Rotation

begins



Attention: The ADS-function will switch on the control of the laser 10 sec.

after the laser has completely been levelled (adjustment phase). Tilt display

(K) emits long blink signals during the adjustment phase and short blink

signals when ADS is activated.

ADS-function:

Titanium

Deutsch 1

ENGLISH

AReference laser outlet

BPrism head

CReceiver diode for remote control

(4x)

DControl panel

EBattery compartment

Fauto/man button

GON / OFF button

HAnzeigen X, Y und Z-Achsen

IOperating / Battery display

JTilt button

KTilt display

L5/8 “ tripod adapter for vertical

use

MVertical holder (screw adjustment)

NAdjusting screws

OCentric point (with hinge)

PQuick sighting

Q5/8” thread

RVertical vial for pre-adjustment

SCharger socket (DC 6V)

TBattery charge display

Vertical operation



Titanium

ENGLISH

Key pads and symbols LCD-Display

14 Speed / Angle range / Adjusting

axis at auto/man mode /

Volume at Hand receiver mode

15 Position

16 Rotations-Modus

17 Scan mode

18 Hand receiver mode

19 Calibration mode:

Switch X-, Y,-axis

20 Calibration mode: Adjusting axis

21 Calibration mode: Saving the new

calibration.

22 Display measuring range selection

23 Hand receiver above laser level

24 Precisely on laser level

25 Hand receiver below laser level

26 Acoustic signal display

27 Low battery display

28 Hand receiver mode /

Switch: Precision range

Free-hand range

(Volume only)

Note:

The laser receiver has two tolerance settings: Precision and free-hand setting.

On the SensoCommander 120, the settings are indicated by LEDs: precision set-

ting: green; free-hand setting: orange.

Commader 50 SensoCommander SensoLite

Titanium

Deutsch 1

ENGLISH

Operation of the Titanium

Charging the batteries

• Before using the divice, fully charge th

batteries

• Open the battery compartment (E), insert

the batteries and connect the plugs to

the sockets. The plugs fit in the sockets in

one position only (see pictures on right).

Reclose the battery compartment.

• Connect the battery charger/mains unit

to a mains source and plug into the

socket (S). Please only use the

charger/mains unit supplied with the

device. If a different one is used, the war-

ranty will become void.

• The device can also be operated with standard alkali batteries (4 x type D).

Insert the batteries as shown by the installation symbols. Ensure the polarity

is correct.

• If the LED (T) blinks constantly, either the batteries must be exchanged or

recharged.

Insertion of batteries in the SensoLite and SensoCommander:

• Remove the battery cover (9) and insert the batteries as shown by the

installation symbol, ensuring that the polarity is correct. Then replace the

cover.

• To extend battery life, the receiver switches off automatically after about 5

minutes if not used.



Note:

Do not expose batteries to excessive heat such as sunshine, fire, etc. Dry batteries

must not be recharged. Used batteries must not be disposed of as household

waste. Please take them to a collection point for used batteries or for special

waste. Ask your local authority for further details. Batteries with the recycling

symbol can also be returned to our dealerships or to our Technical Service.

Horizontal and vertical use

Setting up:

• Horizontal: Position the device on a level surface or on a tripod.

• Vertical - fix vertical holder (M), unfold centric point (O) and position unit in

vertical mode. Pre-adjust unit with vertical vial (R) and adjusting screws (N).

The sensor then adjusts the unit automatically. For use on tripods remove

vertical holder (M) and screw-on tripod holder (L).

• PRESS THE "ON/OFF" SWITCH (G).

• The device automatically levels itself within a range of ± 5°. When levelling

has been completed, the laser rotates at maximum speed. The operating

display (I) is lit up and the rotary laser is in the hand receiver mode. Switch

on the laser receiver with the button (18), the button (18) and the laser

beam is recognised.

Turn the vertical plane:

• In vertical use the laser plane can exactly be turned. Press auto/man

button (F).

• The vertical plane (+ 5°) can now be changed with the Commander 50 or

SensoCommander. To do this press buttons (14)

Manual Slope function:

• The Sensor-Automatic adjusts the X and Y axes. However, if it

is intended to project an incline, Sensor-Automatic must be

switched off.

• To project an aincline, press the auto/man (F) button. The X

axis can now be adjusted, and the X axis display (H) lights up.

To adjust the inclination of the Y axis, press the tilt button (J);

the Y axis display (H) lights up.

• Adjustment of the X and Y axes is done using the Commander 50 or

SensoCommander. To do this, press buttons (15).

In 1 plane

In 2 planes

Titanium

ENGLISH 21



Note: If the device is too far off the horizontal (more than 5°), a warning signal

will sound and the rotor head will stop. In this case, the device must be

repositioned on a more level surface.

Laser modes

The following modes can be controlled with the Commander 50 up

to a maximum distance of 50 m. Open battery compartment and

insert battery according to picture on the right, ensure polarity is

correct and close battery compartment. The rotating laser can also

be controlled with the SensoCommander.

Point mode

To establish point mode, press button (16) repeatedly until

the laser no longer rotates. The laser can then be precisely

positioned to the measuring level with the direction

buttons (15).

Rotary mode

Use button (16) to set the desired speed of rotation: 0, 150, 500 rpm.

Scan mode

Button (17) can be used to activate and set an intensive light segment

with one of 4 different widths. The segment can be positioned with the

direction buttons (15).

Hand receiver mode

Working with the optional laser receiver: Switch on

the SensoLite laser receiver with the botton (18).

With the Commander 50 and SensoCommander you

could set the maximum rotary speed, 500 rpm. It is

able to detect the laser beam at a great distance

now. Move the SensoLite up and down through the

laser beam until the middle indicator (24) appears.

Mark the measured height at the perimeter marking

groove.

SpotLite Marking: The projected light beam at the

height of the laser beam simplifies precise marking

and prevents parallax error.

Titanium

ENGLISH

Universal mount (optional):

The laser receiver can be installed on levelling

staffs with the aid of the universal mount. The

Flexi measuring staff (Art. No. 080.50) is always

recommended when measuring from floor

heights. It also allows you to determine heights

directly without any need for calculation.

Titanium Green (Laser class 3R)

The distance at which a laser is visible to the naked eye depends on its colour

i.e. wavelength. This is because of the human eye's physiology – green appe-

ars brighter to us than red. Depending on ambient light, green lasers are the-

refore many times more visible than red lasers; in indoor areas this is as much

as 12 times brighter. This permits applications on dark surfaces, over longer

distances and work in very bright ambient light. A red laser with a 635 nm

wavelength is used as a reference value for brightness differentiation.

In contrast to red lasers, green laser light can only be produced indirectly. This

is a source of potential characteristic fluctuations:

• The optimal operating temperature is 20°C. Outside of the operating tem-

perature range of 0 ... 45°C green lasers become darker. IMPORTANT:

Allow the unit enough time to adapt to the ambient temperature before

switching the unit on.

• Laser brightness may vary somewhat from one unit to another. This is a

natural phenomena and excluded from warranty claims.

• Green Laser will only work with certain Receivers. The maximum range of

the Receiver is shorter, please refer to technical details.

Additional safety recommendations for Laser Class 3R.

• The laser must never be allowed to shine into people’s eyes, whether inten-

tionally or accidentally. • Always keep the eyes at least 15 cm away from the

reflection of the laser beam on a surface. • Never point the laser at reflecting

surfaces. • Never look at the laser beam through optical devices (magnifying

glass, microscope, binoculars, ...). • If possible, shield off the pathway of the

laser beam, e.g. by screens or other devices. • Mark off the work area by cor-

dons and warning signs. • If possible, the laser beam should not run at eye

level (1.60 m ... 1.90 m).

Titanium

ENGLISH 23

Tabla de contenidos

Otros manuales de Nivel láser de LaserLiner

LaserLiner

LaserLiner AL 22 Classic Manual de usuario

LaserLiner

LaserLiner DigiLevel Laser Manual de usuario

LaserLiner

LaserLiner HandyLaser Manual de usuario

LaserLiner

LaserLiner SensoLite 100 Manual de usuario

LaserLiner

LaserLiner ActiveFinder XP Manual de usuario

LaserLiner

LaserLiner CompactCross-Laser Manual de usuario

LaserLiner

LaserLiner DigiLevel Compact Manual de usuario

LaserLiner

LaserLiner PowerCross-Laser 5G Manual de usuario

LaserLiner

LaserLiner DuraMax Manual de usuario

LaserLiner

LaserLiner CompactCross-Laser Pro Manual de usuario

LaserLiner

LaserLiner AutoCross Laser 2 Manual de usuario

LaserLiner

LaserLiner AutoCross-Laser ACL 2C RX Manual de usuario

LaserLiner

LaserLiner SuperCross-Laser SCL 3 Manual de usuario

LaserLiner

LaserLiner ArcoMaster 40 Manual de usuario

LaserLiner

LaserLiner SmartCross-Laser Manual de usuario

LaserLiner

LaserLiner AutoCross-Laser 3C Manual de usuario

LaserLiner

LaserLiner PrecisionCross-Laser PCL 8 Manual de usuario

LaserLiner

LaserLiner CompactCube-Laser 3 Manual de usuario

LaserLiner

LaserLiner BeamControl-Master Manual de usuario

LaserLiner

LaserLiner AutoCross-Laser ACL 3C Manual de usuario

LaserLiner

LaserLiner ThermoSpot Manual de usuario

LaserLiner

LaserLiner SuperSquare-Laser 2G Manual de usuario

LaserLiner

LaserLiner SuperCross-Laser SCL 3 Manual de usuario

LaserLiner

LaserLiner AutoCross-Laser 2 Plus Manual de usuario

Manuales populares de Nivel láser de otras marcas

Nedo

Nedo ET-5 Manual de usuario

geo-FENNEL

geo-FENNEL Maxi-Liner FL 65 HP Manual de usuario

Spectra

Spectra LL300N Manual de usuario

geo-FENNEL

geo-FENNEL Selection PRO FLG 40-PowerCross GREEN SP Manual de usuario

Nedo

Nedo Crossliner 4 Manual de usuario

Lasertec

Lasertec FX360G Manual de usuario

Flex

Flex ALC 8 Manual de usuario

Black & Decker

Black & Decker LZR5 Manual de usuario

Johnson

Johnson 40-6692 Manual de usuario

Cocraft

Cocraft HL 20-SG Manual de usuario

Zircon

Zircon iLine Manual de usuario

HWH

HWH 310 SERIES Manual de usuario

Leica

Leica iCON robot 60 Manual de usuario

DeWalt

DeWalt DW082 Manual de usuario

imex

imex EL20 Manual de usuario

Fixturlaser

Fixturlaser NXA D I-0912 Manual de usuario

Wacker Neuson

Wacker Neuson PAL450 Manual de usuario

Metrica

Metrica 33806 Manual de usuario