Larson Electronics EMGBALL-LED3 Manual de usuario

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

! IMPORTANT SAFEGUARDS ! WHEN USING ELECTRICAL EQUIPMENT, BASIC

SAFETY PRECAUTIONS SHOULD ALWAYS BE

FOLLOWED, INCLUDING THE FOLLOWING:

SAVE THESE INSTRUCTIONS

THIS PRODUCT CONTAINS A RECHARGEABLE NICKEL-CADMIUM BATTERY.

THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.

1. Do not join converter connector until installation is complete and AC Power is supplied to the emergency driver.

2. This product is for use with an emergency LED lighting load and supplies nominal 10.0 W of power with a

maximum voltage of 50 VDC in emergency mode for a minimum of 90 minutes.

3. Make sure all connections are in accordance with the National Electrical Code or Canadian Electrical Code and

any local regulations.

4. To reduce the risk of electric shock, disconnect both normal and emergency power supplies and converter

connector of the emergency driver before servicing.

5. This emergency driver is suitable for factory installation only.

6. This product is suitable for use in damp locations where the ambient temperature is 0ºC minimum, +55ºC

maximum. Product is also suitable for installation in sealed and gasketed ﬁ xtures. Product is not suitable

for heated air outlets and wet or hazardous locations. Maximum allowable case temp is 65ºC.

7. An unswitched AC power source is required (120-277 VAC, 50/60 Hz).

8. Do not install near gas or electric heaters.

9. Do not attempt to service the battery. A sealed, no-maintenance battery is used that is not ﬁeld replaceable.

Contact the manufacturer for information on service.

10. The use of accessory equipment not recommended by the manufacturer,may cause an unsafe condition.

11. Do not use this product for other than intended use.

12. Servicing should be performed by qualiﬁed service personnel.

13. Equipment should be mounted in locations and at heights where it will not be subjected to tampering by

unauthorized personnel.

14. For Canadian application,the output terminals should be in compliance with the accessibility requirement of

the Canadian Electric Code.

15. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

this device may not cause harmful interference, and (2) this device must accept any interference that may cause

undesired operation.

16. This product must be grounded. See the wiring diagrams for details.

Ni - Cd

EMGBALL-LED3

Replacement Emergency Backup Ballast

for EMG Explosion Proof LED Light Fixtures

Instruction Manual

Larson Electronics, LLC Phone: (877) 348-9680 Fax: (903) 498-3364 www.larsonelectronics.com 1of 2

INSTALLATION

NOTE: Make sure the necessary branch circuit wiring is available. An unswitched source of power is

required. The emergency driver must be fed from the same branch circuit as the AC driver.

CAUTION: DO NOT JOIN CONVERTER CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS

SUPPLIED TO THE EMERGENCY DRIVER.

>Mounting Height: This product meets or exceeds the NFPA minimum light requirements with all loads, down to the

smallest rated lamp load, at heights up to 7.17ft (2.2m). Many factors inﬂuence emergency illumination levels, such as

the lamp load selected, luminare design, and environmental factors therefore end use veriﬁcation is necessary. For ﬁeld

installations, when the attached luminaire is mounted at heights greater than 7.17ft (2.2m), the level of illumination

must be measured in the end application to ensure the requirements of NFPA 101 and local codes are satisﬁed.

>Remote Mounting: The emergency LED driver may be remote mounted from the luminaire. If used in conjunction with

an AC driver the allowed distance is up to half the distance the AC driver manufacturer recommends remote mounting

the AC driver from the LED load. If used without an AC driver, and remote mounting more than 5 feet from the luminaire,

please consult the factory to determine the necessary wire gauge. CAUTION: Remote mounting can result in reduced

power output.

EMERGENCY DRIVER AND AC DRIVER MUST BE FED FROM THE SAME BRANCH CIRCUIT

WIRING DIAGRAMS

FIG A TWO (2) WIRE INTEGRATED TEST SWITCH

:$//6:,7&+

:+75('

9,2/(7

%52:1

+27

%/$&.

$&'5,9(5

:+,7(

:+7%/.

&20021

<(//2:

<(/%/.

%/8(

/('

/('

$&'5,9(5

$&'5,9(5

/('/2$'

:+,7(

%/$&.

5('

&219(57(5

&211(&725

%52:1

9,2/(7

(PHUJHQF\

/('

'ULYHU

*5((1

FIG B EMERGENCY ONLY

TYPICAL SCHEMATICS ONLY. MAY BE USED WITH OTHER DRIVERS. CONSULT THE FACTORY FOR OTHER WIRING DIAGRAMS.

9,2/(7

%52:1

+27 %/$&.

:+,7(

:+7%/.

&20021

<(//2:

<(/%/.

%/8(

/('

/('

/('/2$'

5('

&219(57(5

&211(&725

%52:1

9,2/(7

(PHUJHQF\

/('

'ULYHU

&$3

*5((1

:+75('

&$3

NOTE: For short-term testing of the emergency function, the battery must be charged for at least one hour. The

emergency driver must be charged for at least 24 hours before conducting a long-term test.

During normal operation AC power is applied, the charging indicator light is illuminated, indicating that the battery is

being charged. When power fails, the emergency LED driver automatically switches to emergency power (internal battery),

operating the LED load for a minimum of 90 minutes. When AC power is restored, the emergency driver returns to the

charging mode.

Although no routine maintenance is required to keep the emergency driver functional, it should be checked periodically to

ensure that it is working. The following schedule is recommended:

1. Visually inspect the charging indicator light monthly. It should be illuminated. If the charging indicator is

flashing. Contact tech support.

2. Test the emergency operation of the fixture at 30-day intervals for a minimum of 30 seconds. The LED load

should operate at reduced illumination.

3. Conduct a 90-minute discharge test once a year. The LED load should operate at reduced illumination for at

least 90 minutes.

! REFER ANY SERVICING INDICATED BY THESE CHECKS TO QUALIFIED PERSONNEL !

OPERATION

MAINTENANCE

TCASE TEST POINT LOCATION

PP

PP

Wire Harness Entry

Larson Electronics, LLC Phone: (877) 348-9680 Fax: (903) 498-3364 www.larsonelectronics.com 2of 2

Tabla de contenidos

Otros manuales de Equipo de iluminación de Larson Electronics

Larson Electronics

Larson Electronics EMGBALL-LED1-LV Manual de usuario

Larson Electronics

Larson Electronics VPLHL-7WLED-GR30 Manual de usuario

Larson Electronics

Larson Electronics EPL-EMG-CM-42W Manual de instrucciones

Larson Electronics

Larson Electronics LEDLB-4-IR Manual de usuario

Larson Electronics

Larson Electronics LED18W-PAR36 Manual de usuario

Larson Electronics

Larson Electronics EPL-SBDL-150RT-48 Manual de usuario

Larson Electronics

Larson Electronics LEDP5W-60XC-1227 Manual de usuario

Larson Electronics

Larson Electronics EPL-SL-2-LED-ITG-M2 Manual de usuario

Larson Electronics

Larson Electronics EXP-EMG-EXT-LE6-3L Manual de usuario

Larson Electronics

Larson Electronics EPL-LED-50W-RT-JB2 Manual de usuario

Larson Electronics

Larson Electronics EPL-HB-50LED-RT Manual de usuario

Larson Electronics

Larson Electronics EPLC2-PT-2X150LED-RT Manual de usuario

Larson Electronics

Larson Electronics EPL-HB-150LED-RT-100-EPP Manual de usuario

Larson Electronics

Larson Electronics PML-15 Manual de usuario

Larson Electronics

Larson Electronics GSLEDIP6-C1D2 Manual de usuario

Larson Electronics

Larson Electronics BL24-LED-600V-100-HD Manual de usuario

Larson Electronics

Larson Electronics GVP-48-2L-LED-48VDC-R2 Manual de usuario

Larson Electronics

Larson Electronics EPL-24-2L-LED-VISRED Manual de usuario

Larson Electronics

Larson Electronics ORS-120-8M-4X150W-LED Manual de usuario

Larson Electronics

Larson Electronics PTB-1-75FT Manual de usuario

Larson Electronics

Larson Electronics HALD-48-1X100LED Manual de usuario

Larson Electronics

Larson Electronics LED10W-1X4LT Manual de usuario

Larson Electronics

Larson Electronics WAL-C-4XM Manual de usuario

Larson Electronics

Larson Electronics MMLP-150LED-RT-12P Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario