Larson Electronics EMGBALL-LED1-LV Manual de usuario

EMGBALL-LED1-LV

INSTRUCTION MANUAL

EMGBALL-LED1-LV

Larson Electronics, LLC

Phone: 877-348-9680

Fax: (903) 498-3364 www.larsonelectronics.com

1 of 4

Replacement Emergency Ballast for EMG

Explosion Proof LED Light Fixtures with Low

Voltage Bulbs

Instruction Manual

Thank you for your purchase of the EMGBALL-LED1-LV from Larson Electronics.

WARNING

Standard Warning (General)

WARNING:

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

CRITICAL SAFETY INSTRUCTIONS:

•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY

RELEVANT LOCAL BUILDING CODES.

•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL

SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.

•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.

•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.

•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP

OBJECTS. SUITABLE FOR DAMP LOCATIONS.

WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE

INSTALLATION OR PERFORMING ANY MAINTENANCE.

RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.

RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.

RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.

SAVE THESE INSTRUCTIONS

EMGBALL-LED1-LV

Larson Electronics, LLC

Phone: 877-348-9680

Fax: (903) 498-3364 www.larsonelectronics.com

2 of 4

1. Do not join converter connector until installation is complete and AC Power is supplied to the emergency driver.

2. This product is for use with an emergency LED lighting load and supplies nominal 10.0 W of power with a

maximum voltage of 50 VDC in emergency mode for a minimum of 90 minutes.

3. Make sure all connections are in accordance with the National Electrical Code or Canadian Electrical Code and

any local regulations.

4. To reduce the risk of electric shock, disconnect both normal and emergency power supplies and converter

connector of the emergency driver before servicing.

5. This emergency driver is suitable for factory installation only.

6. This product is suitable for use in damp locations where the ambient temperature is 0ºC minimum, +55ºC

maximum. Product is also suitable for installation in sealed and gasketed ﬁxtures. Product is not suitable

7. for heated air outlets and wet or hazardous locations. Maximum allowable case temp is 65ºC. See Page 4 for

Tcase measurement location.

8. An unswitched AC power source is required (120-277 V AC, 50/60 Hz).

9. Do not install near gas or electric heaters.

10. Do not attempt to service the battery. A sealed, no-maintenance battery is used that is not ﬁeld replaceable.

Contact the manufacturer for information on service.

11. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.

12. Do not use this product for other than intended use.

13. Servicing should be performed by qualiﬁed service personnel.

14. Equipment should be mounted in locations and at heights where it will not be subjected to tampering by

unauthorized personnel.

15. For Canadian application the output terminals should be in compliance with the accessibility requirement of the

Canadian Electric Code.

16. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this

device may not cause harmful interference, and (2) this device must accept any interference that may cause

undesired operation.

17. This product must be grounded. See the wiring diagrams for details.

INSTALLATION

CAUTION: DO NOT JOIN CONVERTER CONNECTOR UNTIL INSTALLATION IS

COMPLETE AND AC POWER IS SUPPLIED TO THE EMERGENCY DRIVER.

NOTE: Make sure the necessary branch circuit wiring is available. An unswitched source of power is required. The

emergency driver must be fed from the same branch circuit as the AC driver.

•Mounting Height: This product meets or exceeds the NFPA minimum light requirements with all loads, down to

the smallest rated lamp load, at heights up to 7.17ft (2.2m). Many factors inﬂ uence emergency illumination

levels, such as the lamp load selected, luminare design, and environmental factors therefore end use veriﬁ

cation is necessary. For ﬁ eld installations, when the attached luminaire is mounted at heights greater than 7.17ft

(2.2m), the level of illumination must be measured in the end application to ensure the requirements of NFPA

101 and local codes are satisﬁ ed.

•Remote Mounting: The emergency LED driver may be remote mounted from the luminaire. If used in

conjunction with an AC driver the allowed distance is up to half the distance the AC driver manufacturer

recommends remote mounting the AC driver from the LED load. If used without an AC driver, and remote

mounting more than 5 feet from the luminaire, please consult the factory to determine the necessary wire gauge.

CAUTION: Remote mounting can result in reduced power output.

EMGBALL-LED1-LV

Larson Electronics, LLC

Phone: 877-348-9680

Fax: (903) 498-3364 www.larsonelectronics.com

3 of 4

During normal operation AC power is applied, the charging indicator light is illuminated, indicating that the

battery is being charged. When power fails, the emergency LED driver automatically switches to emergency

power (internal battery), operating the LED load for a minimum of 90 minutes. When AC power is restored, the

emergency driver returns to the charging mode.

OPERATION

MAINTENANCE

Although no routine maintenance is required to keep the emergency driver functional, it should be checked

periodically to ensure that it is working. The following schedule is recommended:

1. Visually inspect the charging indicator light monthly. It should be illuminated. If the charging indicator is

flashing. Contact tech support.

2. Test the emergency operation of the fixture at 30-day intervals for a minimum of 30 seconds. The LED

load should operate at reduced illumination.

3. Conduct a 90-minute discharge test once a year. The LED load should operate at reduced illumination for

at least 90 minutes.

! REFER ANY SERVICING INDICATED BY THESE CHECKS TO QUALIFIED PERSONNEL !

USE AND CARE

Unauthorized modification may impair the function and/or safety of this device and could affect the life of the

equipment. Always check for damaged or worn out parts before using the device. Store it in a secure place out of the

reach of children when not in use.Inspect for good working condition prior to storage and before re-use.

REPLACEMENT PARTS

The EMGBALL-LED1-LV is designed to provide years of reliable performance. Should the need for replacement parts

arise, please contact Larson Electronics.

THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION

REQUIREMENTS. SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON

ELECTRONICS BY EMAIL AT SALE[email protected] OR BY PHONE AT 1-877-348-9680 FOR FURTHER ASSISTANCE.

PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.

EMGBALL-LED1-LV

Larson Electronics, LLC

Phone: 877-348-9680

Fax: (903) 498-3364 www.larsonelectronics.com

4 of 4

DIAGRAMS

TCASE TEST POINT LOCATION

PP

PP

Wire Harness Entry

WIRING DIAGRAMS

EMERGENCY DRIVER AND AC DRIVER MUST BE FED FROM THE SAME BRANCH CIRCUIT

TYPICAL SCHEMATICS ONLY. MAY BE USED WITH OTHER DRIVERS. CONSULT THE FACTORY FOR OTHER

WIRING DIAGRAMS.

FIG A TWO (2) WIRE INTEGRATED TEST SWITCH

:$//6:,7&+

:+75('

9,2/(7

%52:1

+27

%/$&.

$&'5,9(5

:+,7(

:+7%/.

&20021

<(//2:

<(/%/.

%/8(

/('

/('

$&'5,9(5

$&'5,9(5

/('/2$'

:+,7(

%/$&.

5('

&219(57(5

&211(&725

%52:1

9,2/(7

(PHUJHQF\

/('

'ULYHU

*5((1

FIG B EMERGENCY ONLY

9,2/(7

%52:1

+27 %/$&.

:+,7(

:+7%/.

&20021

<(//2:

<(/%/.

%/8(

/('

/('

/('/2$'

5('

&219(57(5

&211(&725

%52:1

9,2/(7

(PHUJHQF\

/('

'ULYHU

&$3

*5((1

:+75('

&$3

NOTE: For short-term testing of the emergency function, the battery must be charged for at least one hour. The emergency

driver must be charged for at least 24 hours before conducting a long-term test.

Tabla de contenidos

Otros manuales de Equipo de iluminación de Larson Electronics

Larson Electronics

Larson Electronics EPL-HB-150LED-RT-100-EPP Manual de usuario

Larson Electronics

Larson Electronics PTB-1-50FT Manual de usuario

Larson Electronics

Larson Electronics VPLHL-7WLED-GR30 Manual de usuario

Larson Electronics

Larson Electronics LEDLB-12E-F-M-1227 Manual de usuario

Larson Electronics

Larson Electronics EPL-HB-150LED-RT-140DB-JB3 Manual de usuario

Larson Electronics

Larson Electronics EPL-HB-150LED-RT Manual de usuario

Larson Electronics

Larson Electronics EPL-TP-2XRUL10 Manual de usuario

Larson Electronics

Larson Electronics TPM-2XWP60E-10C Manual de usuario

Larson Electronics

Larson Electronics EPL-FL1524-LED Series Manual de usuario

Larson Electronics

Larson Electronics RL-15-LED-CPR Manual de usuario

Larson Electronics

Larson Electronics EPL-FL1524-100 Manual de usuario

Larson Electronics

Larson Electronics EPL-QC-16C-2X150LED-RT-X24V-C1D1-12.3-100-EPP Manual de usuario

Larson Electronics

Larson Electronics C1D2 Manual de usuario

Larson Electronics

Larson Electronics C1D1-2 Manual de usuario

Larson Electronics

Larson Electronics EPLC2-LED-150W-RT-DNS Manual de usuario

Larson Electronics

Larson Electronics EPL-PM-1X30LED-6XMB-10 Manual de usuario

Larson Electronics

Larson Electronics EPL-WPLED-100W-RT-PSC Manual de usuario

Larson Electronics

Larson Electronics EPL-FL1524-25-1523 Manual de usuario

Larson Electronics

Larson Electronics EPLX-SL-PT-3X80W.RD2-TRC-20X-100C Manual de usuario

Larson Electronics

Larson Electronics EPL-TFM-150LED-RT Manual de usuario

Larson Electronics

Larson Electronics EPL-LB-50LED-RT-180B Manual de usuario

Larson Electronics

Larson Electronics FRL-EMX-18-90W-FUVC-KT Manual de usuario

Larson Electronics

Larson Electronics HAL-PM-185LED-CPR Manual de usuario

Larson Electronics

Larson Electronics EPL-HB-150LED-RT-DLC Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario