Lantech IES-3208C Manual de usuario

IES-3208C/3307C

IPES-3208C/3307C

IPES-3208CB/3307CB

8 (7)10/100Tx + 2(3) 10/100/1000T/Dual Speed SFP Combo and (8/7

PoE at/af) (Mode A/Mode B)Industrial Managed Switch w/ITU

G.8032 Ring

User Manual

Mar. 2014

Important Notice

Lantech Communications Global, Inc. reserves the right to modify the

equipment, its specification or this manual without prior notice, in the interest

of improving performance, reliability, or servicing. At the time of publication

all data is correct for the operation of the equipment at the voltage and/or

temperature referred to. Performance data indicates typical values related to

the particular product.

No part of this documentation or information supplied may be divulged to any

third party without the express written consent of Lantech Communications

Global Inc. Products offered may contain software which is proprietary to

Lantech Communications Global Inc. The offer or supply of these products

and services does not include or infer any transfer of ownership.

Interference Issues

This Equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC rules. These limits are

designed to provide reasonable protection against harmful interference in a

commercial or industrial installation. This equipment generates, uses, and

can radiate radio frequency energy. It may cause harmful interference to

radio communications if the equipment is not installed and used in

accordance with the instructions.

FCC Warning

This Equipment has been tested and found to comply with the limits for a

Class-A digital device, pursuant to Part 15 of the FCC rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy. It may cause harmful interference to radio

communications if the equipment is not installed and used in accordance

with the instructions. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

CE Mark Warning

This is a Class-A product. In a domestic environment this product may

cause radio interference in which case the user may be required to take

adequate measures.

Content

Chapter 1 Introduction ........................................... 1

Hardware Features................................................. 1

Software Features.................................................. 3

Chapter 2 Hardware Description............................ 8

2.1 Physical Dimension....................................... 8

2.2 IP Protection................................................10

2.3 LED Indicators.............................................13

Chapter 3 Hardware Installation .......................... 14

3.1Hardware installation........................................14

3.2 DIN-Rail Mounting........................................15

3.3 Wall Mount Plate Mounting ..........................17

3.4 Wiring the Power Inputs...............................18

3.5 Wiring the Fault Alarm Contact ....................19

3.6 Cabling ........................................................20

Chapter 4 Network Application............................ 23

ITU G.8032 Scheme..............................................23

Ring Coupling ..........................................................23

Multiple Rings..........................................................24

Dual Homing ...........................................................25

Chain......................................................................25

Chapter 5 Console Management.......................... 27

5.1 Connecting to the Console Port....................27

5.2 Login in the Console Interface......................28

Chapter 6 Web-Based Management.................... 29

6.1 About Web-based Management...................29

6.2 Preparing for Web Management ..................29

6.3 System Login...............................................30

6.4 System.........................................................31

6.4.1 System Identification Configuration...................... 31

6.4.2 Switch Information................................................ 32

6.4.3 IP configuration..................................................... 32

6.4.4 DHCP server......................................................... 34

6.4.5 System Time ................................................... 35

6.4.6 SNMP Configuration.......................................... 39

6.4.7 Fault Relay Configuration .................................. 40

6.4.8 Digital Input/Output....................................... 42

6.5 Event & Log................................................44

6.5.1 View Logs ............................................................. 44

6.5.2 Events................................................................... 45

6.5.3 DDM event............................................................ 46

6.5.4 Actions.................................................................. 47

6.5.5 Event Action Map ................................................. 50

6.6 Ports................................................................52

6.6.1 Device Settings..................................................... 52

6.6.2 Status................................................................. 53

6.6.3 Statistics ............................................................... 53

6.6.4 Mirroring................................................................ 54

6.6.5 Rate Limiting......................................................... 55

6.6.6 Loop Protection..................................................... 56

6.7 Power over Ethernet (IPES series) ..................57

6.7.1 Configuration(PoE Mode A) ................................. 58

6.7.2 Status.................................................................... 59

6.7.3 Detection............................................................... 61

6.7.4 Scheduling............................................................ 63

6.7.5 Configuration(PoE Mode B) ................................. 64

6.7.6 Configuration(PoE Mode B) ................................. 65

6.7.7 Detection(Mode B)................................................ 65

6.7.8 Scheduling(Mode B)............................................. 67

6.8 Topology..........................................................68

6.9 QoS.................................................................71

6.9.1 QoS Policy............................................................ 71

6.10 Security .........................................................73

6.10.1 MAC Address Tables.......................................... 73

6.10.2 Access Control List............................................. 74

6.10.3 IEEE 802.1X Radius Server............................... 75

6.10.4 IP Security .......................................................... 76

6.11 VLAN.............................................................77

6.11.1 802.1Q VLAN Config.......................................... 77

6.11.2 Status.................................................................. 79

6.12 MVR..............................................................80

6.12 LLDP .............................................................81

6.12.1 LLDP Configuration ............................................ 81

6.12.2 LLDP Neighbor................................................... 82

6.12.3 LLDP Statistics ................................................... 84

6.13 CDP...............................................................87

6.13.1 CDP Configuration Device Settings ................... 87

6.13.2 CDP Port Configuration...................................... 88

6.13.3. CDP Status........................................................ 88

6.14 IGMP Snooping .............................................90

6.14.1 IGMP Snooping Configuration............................ 91

6.14.2 IGMP Snooping Status....................................... 92

6.15 MSTP ............................................................94

6.15.1. MSTP Global Configuration .......................94

6.15.2 How to enable MSTP.......................................... 95

6.15.3 CIST Settings...................................................... 97

6.15.3.1 Bridge configuration.......................... 97

6.15.3.2 Port.................................................... 97

6.15.4. MSTP MSTI Settings......................................... 98

6.15.5. MSTP Bridges Status........................................ 99

6.15.6. Bridge status of all ports.................................. 100

6.16 Aggregation..............................................101

6.16.1. Aggregation Configuration............................... 101

6.16.2 LACP Port Status ............................................. 102

6.17 G.8032 ERPS..............................................104

6.17.1. G.8032 Ethernet Ring Protection Configuration105

6.17.2 How to set ERPS G.8032................................. 106

6.18 Dual Homing.............................................108

6.19 Maintenance................................................110

6.19.1 Save Configuration........................................... 110

6.19.2 Config backup/restore................................ 110

6.19.3 Restart device................................................... 111

6.19.4 Firmware Upgrade............................................ 112

6.19.5 Diagnostics....................................................... 112

Appendix —Command Line mode ...................... 116

Chapter 1 Introduction

Lantech IES-3208/3307 series(include PoE series) are high performance L2+industrial

8 (7)10/100Tx + 2(3) 10/100/1000T/Dual Speed SFP Combo (with 7/8 PoE at/af

injectors- IPES series) which provides L2 wire speed and advanced security function for

connecting PD network. They delivers ITU G.8032 ring recovery less than 20ms,

comprehensive QoS, , IGMPv1/v2/v3 & IGMP routing port, MVR (multicast VLAN

registration) , LACP link aggregation and advanced security including ACL, TACAS+*,

SSH/SSL, DHCP Option 82*which are important features required in large network. It

also supports Cisco Discovery Protocol (CDP) and LLDP for Ciscoworks to detect the

switch info to be shown on L2 map topology. The user friendly UI, innovative auto

topology drawing and topology demo makes Lantech Full gigabit series much easier to

get hands-on.

Hardware Features

Standard

IEEE 802.3 10Base-T Ethernet

IEEE 802.3u 100Base-TX

IEEE802.3z Gigabit fiber

IEEE802.3x Flow Control and Back Pressure

IEEE802.3ad Port trunk with LACP

IEEE802.1d Spanning Tree

IEEE802.1w Rapid Spanning Tree

IEEE802.1s Multiple Spanning Tree

IEEE 802.3ad Link Aggregation Control Protocol (LACP)

IEEE 802.1AB Link Layer Discovery Protocol (LLDP)

IEEE 802.1X User Authentication (Radius)

IEEE802.1p Class of Service

IEEE802.1Q VLAN Tag

IEEE802.3at/af Power over Ethernet

Switch

Architecture

Back-plane (Switching Fabric): 5.6(3208)/7.4Gbps(3307)

Transfer Rate

14,880pps for Ethernet port

148,800pps for Fast Ethernet port

1,488,000pps for Gigabit Ethernet port

MAC Address

16K MAC address table

Connector

10/100Tx: 8(7) x RJ-45 type connector(2/3 will reserve for

combo SFP port)

Dual Speed SFP Combo: 2(3) x 1000 SFP Sockets

Power & P-Fail connector: 1 x 6-pole terminal block

Digital Input/Output: 1 x 6-pole terminal block

RS-232 connector: 1 x RJ-45 type connector

USB slot for backup and restore

Network Cable

10/100Tx: 2-pair UTP/STP Cat. 5/ 5E / 6 cable

EIA/TIA-568 100-ohm (100m)

Protocol

CSMA/CD

LED

Per unit: Power 1 (Green), Power 2 (Green), FAULT (Red)

Ethernet port: Link/Activity (Green), 100Tx (Green); Giga-T:

Link/Activity (Green)

PoE FWD(IPES): Green( Mode A), Yellow(Mode B)

DI/DO

1 Digital Input(DI):

Level 0: -30~2V/Level1: 10~30V

Max. input current:8mA

1 Digital Output(DO): open collector to 40VDC, 200mA

Power Supply

48 VDC for 802.3af(IPES series)

54VDC for 802.3at(IPES series)

24~48VDC (IES series)

Power

Consumption

Max 9W for system

PoE Power

Budget

Max. 240W under 48VDC power input (IPES series)

Operating

Humidity

5% to 95% (Non-condensing)

Operating

Temperature

-20oC ~ 60oC

-40oC ~ 75oC(Wide Temp series)

Storage

Temperature

-40oC ~ 85oC

Case Dimension

Metal case. IP-30,

74(W) x 114 (D) x 152 (H) mm

Installation

DIN rail and wall mount ear**

EMI

FCC Class A, CE EN61000-4-2, CE EN61000-4-3, CE EN-

61000-4-4, CE EN61000-4-5,

CE EN61000-4-6, CE EN61000-4-8, CE EN61000-4-11, CE

EN61000-4-12, CE EN61000-6-2, CE EN61000-6-4

Stability Testing

IEC60068-2-32 (Free fall), IEC60068-2-27 (Shock),

IEC60068-2-6 (Vibration)

Software Features

Management

SNMP v1 v2c, v3/ Web/Telnet/CLI

SNMP MIB

RFC 1215 Traps MIB,

RFC 1213 MIBII,

RFC 1157 SNMP MIB,

RFC 1493 Bridge MIB,

RFC 2674 VLAN MIB,

RFC 1643 EtherLike,

RFC 1757 RMON,

RSTP MIB,

Private MIB,

LLDP MIB

ITU G.8032

Support ITU G.8032 v2 for Ring protection in less than

50ms for self-heal recovery < 256 switches ;

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Lantech

Lantech

Lantech IES-2208CA-DNV Manual de usuario

Lantech

Lantech GE-800 Manual de usuario

Lantech

Lantech IGS-0208GSFP Manual de usuario

Lantech

Lantech LGS-2424C Manual de usuario

Lantech

Lantech IPES-3408 Series Manual de usuario

Lantech

Lantech IGS-2404 Manual de usuario

Lantech

Lantech IPGS-0204DSFP-12V Manual de usuario

Lantech

Lantech IPES-5408T Manual de usuario

Lantech

Lantech IPES-3424DSFP-2P Manual de usuario

Lantech

Lantech 5 10/100TX w/ 4 PoE Injector Industrial... Manual de usuario

Lantech

Lantech IPGS-5 Series Manual de usuario

Lantech

Lantech IPES-5222T Series Manual de usuario

Lantech

Lantech IES-0005B Series Manual de usuario

Lantech

Lantech IPES-5408T-X-IGN Series Manual de usuario

Lantech

Lantech IGS-0016 Manual de usuario

Lantech

Lantech IGS-0008A Manual de usuario

Lantech

Lantech LPES-2208CA Manual de usuario

Lantech

Lantech LGS-2300-RPS Manual de usuario

Lantech

Lantech IPGS-0016 Manual de usuario

Lantech

Lantech IES-3 Series Manual de usuario

Lantech

Lantech mini Switch 800 Manual de usuario

Lantech

Lantech IPGS-0204DSFP Manual de usuario

Lantech

Lantech IPES-0104GT-4 Manual de usuario

Lantech

Lantech IPES-3408GSFP Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario