Kramer SL-1N Manual de usuario

KRAMER ELECTRONICS LTD.

USER MANUAL

MODEL:

SL-1N

Master Room Controller

P/N: 2900-300399 Rev 2

SL-1N – Contents

Contents

1Introduction 1

2Getting Started 2

2.1 Achieving the Best Performance 2

2.2 Safety Instructions 3

2.3 Recycling Kramer Products 3

3Overview 4

3.1 Defining the SL-1N Master Room Controller 5

4Connecting the SL-1N 7

4.1 Connecting the RS-232 Port 8

4.2 Connecting the Ethernet Port 9

4.3 Connecting the K-NET Port 9

5Operating the SL-1N 10

6Technical Specifications 11

Figures

Figure 1: SL-1N Master Room Controller 5

Figure 2: Connecting the SL-1N Master Room Controller 8

Figure 3: RS-232 Connection 8

Figure 4: K-NET Pinout Connection 9

SL-1N - Introduction

1 Introduction

Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been

providing a world of unique, creative, and affordable solutions to the vast range of

problems that confront video, audio, presentation, and broadcasting professionals

on a daily basis. In recent years, we have redesigned and upgraded most of our

line, making the best even better!

Our 1,000-plus different models now appear in 14 groups that are clearly defined

by function: GROUP 1: Distribution Amplifiers; GROUP 2: Switchers and Routers;

GROUP 3: Control Systems; GROUP 4: Format/Standards Converters; GROUP 5:

Range Extenders and Repeaters; GROUP 6: Specialty AV Products; GROUP 7:

Scan Converters and Scalers; GROUP 8: Cables and Connectors; GROUP 9:

Room Connectivity; GROUP 10: Accessories and Rack Adapters; GROUP 11:

Sierra Video Products; GROUP 12: Digital Signage; GROUP 13: Audio; and

GROUP 14: Collaboration.

Congratulations on purchasing your Kramer SL-1N Master Room Controller, which

is ideal for the following typical applications:

Master room controller for room control systems

Multimedia room control, such as classrooms and meeting rooms

SL-1N - Getting Started

2 Getting Started

We recommend that you:

Unpack the equipment carefully and save the original box and packaging

materials for possible future shipment

Review the contents of this user manual

Go to http://www.kramerelectronics.com/support/product_downloads.asp

to check for up-to-date user manuals, application programs, and to check if

firmware upgrades are available (where appropriate).

2.1 Achieving the Best Performance

To achieve the best performance:

Use only good quality connection cables (we recommend Kramer high-

performance, high-resolution cables) to avoid interference, deterioration in

signal quality due to poor matching, and elevated noise levels (often

associated with low quality cables)

Do not secure the cables in tight bundles or roll the slack into tight coils

Avoid interference from neighboring electrical appliances that may adversely

influence signal quality

Position your Kramer SL-1N away from moisture, excessive sunlight and

dust

This equipment is to be used only inside a building. It may only be

connected to other equipment that is installed inside a building.

SL-1N - Getting Started

2.2 Safety Instructions

Caution:

There are no operator serviceable parts inside the unit

Warning:

Use only the Kramer Electronics input power wall

adapter that is provided with the unit

Warning:

Disconnect the power and unplug the unit from the wall

before installing

2.3 Recycling Kramer Products

The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC

aims to reduce the amount of WEEE sent for disposal to landfill or incineration by

requiring it to be collected and recycled. To comply with the WEEE Directive,

Kramer Electronics has made arrangements with the European Advanced

Recycling Network (EARN) and will cover any costs of treatment, recycling and

recovery of waste Kramer Electronics branded equipment on arrival at the EARN

facility. For details of Kramer’s recycling arrangements in your particular country

go to our recycling pages at http://www.kramerelectronics.com/support/recycling/.

SL-1N - Overview

3 Overview

The SL-1N is a highly versatile controller; an all-in-one extended remote control

panel for control of AV equipment—especially projectors and associated

equipment—in any room (such as classrooms, boardrooms, or auditoriums). It

streamlines operations and simplifies control by integrating audio, video, and

computer-video sources into a centralized system.

The SL-1N features:

2 bidirectional RS-232 ports to control AV equipment such as projectors,

LCD and PDP displays, power amplifiers, switchers and scalers

3 relay contact closure ports to control other room items related to the AV

system such as raising and lowering drapes, the screen or the projector

IR control - 1 input (3.5mm) and 2 outputs (terminals blocks)

IR Learning that learns commands from any IR remote

Compatibility with Kramer Site-CTRL™ software for network remote control

and management over the Ethernet port

A K-NET™ control channel for connecting compatible user interfaces and

supplying power and control data over a single cable

A USB port for loading device firmware

Flexible control using Ethernet, K-NET™, IR sensors and external IR

commands.

SL-1N - Overview

3.1 Defining the SL-1N Master Room Controller

This section defines the SL-1N.

Figure 1: SL-1N Master Room Controller

Feature

Function

RELAYS Terminal Blocks

Connect to low-voltage relay-driven devices (from 1 to 3)

IR Output Terminal Blocks

Connect to IR emitter cables (from 1 to 2)

RS-232 Terminal Blocks

Connect to the RS-232 devices (from 1 to 2)

ETHERNET RJ-45 Connector

Connects to the PC or other serial controller through

computer networking LAN

DEFAULT Pushbutton

Press to reset to factory default definitions:

IP number 192.168.1.39, mask –255.255.0.0, gateway

–0.0.0.0, also to remove the current configuration

First disconnect the power cord and then connect it again

while pressing the ETH Factory Reset button. The unit

powers up and loads its memory with the factory default

definitions and erases all stored presets

K-NET Terminal Block

PIN GND is for the ground connection; PIN B (-) and PIN

A (+) are for RS-485, and PIN +12V is for powering the

unit

The ground connection is sometimes connected to the

shield of the RS-485 cable

12V DC Connector

For supplying power to the unit

IR IN Sensor and LED

Accepts IR remote commands

IR INPUT 3.5mm Mini Jack

Connects to a remote infrared sensor

NET LED

Illuminates when the Ethernet link is active

SL-1N - Overview

Feature

Function

K-NET LED

Illuminates when the K-NET is active (red –transmit,

green –receive)

RS-232 Tx/Rx LEDs

Illuminates while transmitting/receiving on an RS-232

port (1 to 2) (red –transmit, green –receive)

IR LEDs

Illuminates when an IR port is active

RELAYS LEDs

Illuminates when a relay is active (1 to 3)

SRVC DIP-Switch

Slides down for service use only, slides up for normal

operation

K-NET TERM DIP-Switch

Slides down for K-NET termination, slides up for not

terminated

PROGRAM USB Connector

Connect to a computer for unit configuration and

firmware upgrading

SL-1N - Connecting the SL-1N

4 Connecting the SL-1N

Always switch off the power to each device before connecting it to your

SL-1N. After connecting your SL-1N, connect its power and then

switch on the power to each device.

To connect the SL-1N, as the example in Figure 2 illustrates, do the following:

1. Connect the RELAY terminal block connectors as follows:

Connect RELAY 1 and 2 to blinds

Connect RELAY 3 to a screen

2. Connect the IR outputs as follows:

Connect IR OUTPUT 1 to DVD player 1

Connect IR OUTPUT 2 to DVD player 2

3. Connect the RS-232 ports as follows:

Connect RS-232 port 1 to a projector

Connect RS-232 port 2 to a display

4. Connect the IR sensor as follows:

Connect IR INPUT to an IR sensor

5. Connect the Ethernet port to a network.

6. Connect the K-NET port to any RC device (in this example, an RC-63D) over

K-NET.

Otros manuales para SL-1N

Tabla de contenidos

Otros manuales de Controladores de Kramer

Kramer

Kramer SL-14RC Manual de usuario

Kramer

Kramer VA-4H Manual de usuario

Kramer

Kramer SL-12 Manual de usuario

Kramer

Kramer FC-18 Manual de usuario

Kramer

Kramer SL-1 Manual de usuario

Kramer

Kramer PT-12 Manual de usuario

Kramer

Kramer RC-74DL Manual de usuario

Kramer

Kramer RC-43SL Manual de usuario

Kramer

Kramer RC-7B Manual de usuario

Kramer

Kramer K-NET RC-53D Manual de usuario

Kramer

Kramer KT-107-INWL Manual de usuario

Kramer

Kramer RC-76R Manual de usuario

Kramer

Kramer SL-1 Manual de usuario

Kramer

Kramer FC-18 Manual de usuario

Kramer

Kramer RC-7LC Manual de usuario

Kramer

Kramer RC-7RL Manual de usuario

Kramer

Kramer RC-2 Manual de usuario

Kramer

Kramer FC-26 Manual de usuario

Kramer

Kramer RC-8IR Manual de usuario

Kramer

Kramer SL-240C Manual de usuario

Kramer

Kramer RC-63DLN Manual de usuario

Kramer

Kramer RC-13TC Manual de usuario

Kramer

Kramer RC-52N Manual de usuario

Kramer

Kramer FC-28 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario