Kohler K-10666 Manual de funcionamiento

Maintenance Guide

Exposed Flush Valve

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-10666, K-10673, K-10674, K-10677

1108709-5-E

Table of Contents

EC Declaration of Conformity ............................. 3

Important Information ................................... 4

Your Kohler Electronic Valve .............................. 4

Care and Cleaning ..................................... 5

Control Stop Valve Operation ............................. 7

Remove the DC Sensor ................................. 9

Replace the Battery ................................... 10

Install the DC Sensor .................................. 11

Remove the Solenoid .................................. 12

Install the Solenoid .................................... 13

Clean the Screen/Replace the Piston ...................... 14

Clean/Replace the Diaphragm ........................... 16

Replace the Vacuum Breaker ............................ 18

Replace the Flush Button Assembly ....................... 19

Warranty ........................................... 19

Troubleshooting ...................................... 21

Service Parts ........................................ 25

1108709-5-E 2 Kohler Co.

EC Declaration of Conformity

declare under our sole responsibility that our products, ELECTRONIC FLUSH VALVES, models:

We,

Kohler Company

444 Highland Drive, Kohler, WI 53044

Phone 920-457-4441

EC DECLARATION OF CONFORMITY

K-10673

to which this declaration relates, are in conformity with the following standards:

Electromagnetic Compatibility Directive 89/336/EEC of 3 May 1989 as Amended by

92/31/EEC of 28 April 1992 and 93/68/EEC, Article 5 of 22 July 1993, based on:

• IEC 61000/ IEC 61000-3-:

"Electromagnetic Compatibility (EMC)";

Part 3: "Limits".

Section 2. "Limits for harmonic current emissions (equipment input current up to and including

16A per phase" (2000).

Section 3. "Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage

supply systems, for equipment with rated current <16 A per phase and not subjected to

conditional connection" (1995 + A1:2001).

• EN 61000-6-2/ EN 61000-6-2:

"Electromagnetic Compatibility (EMC) – Part 6-2: Generic standards – Immunity for industrial

environments" (2001).

• EN 55022 Class B:

"Information technology equipment – Radio disturbance characteristics – Limits and methods of

measurements" (1998 A1:2000 + A2:2003).

Low Voltage Directive 73/23/EEC of 19 February 1973 as Amended by 93/68/EEC, Article 13 of

22 July 1993, based on:

• EN 60730/1:

"Specification for Automatic Electrical Controls for Household and Similar Use. General

Requirements".

• EN 60730/2/8:

"Specification for Automatic Electrical Controls for Household and Similar Use. Particular

Requirements for Electrically Operated Water Valves, Including Mechanical Requirements".

Timothy J. Stessman

Codes & Standards Dept.

Kohler Company

November 18, 2008

DateSignature

November 18, 2008 08

K-10677

K-10674

K-10678

K-10675

K-10679

K-10676 K-10668

K-10666

Kohler Co. 3 1108709-5-E

Important Information

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

This device may not cause harmful interference.

This device must accept any interference received, including

interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or

more of the following measures.

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

•Consult the dealer or an experienced radio/television technician

for help.

Modiﬁcations: Any modiﬁcations made to this device that are not

approved by Kohler Co. may void the authority granted to the user by

the FCC to operate this equipment.

This Class B digital apparatus complies with Canadian ICES-003.

Your Kohler Electronic Valve

Design Features

The valve is designed speciﬁcally for use with 1-1/2″(38 mm) top

spud toilets as offered by Kohler Company and others.

The valve is supplied with factory preset timing values. No

programming or adjustment is required.

1108709-5-E 4 Kohler Co.

Your Kohler Electronic Valve (cont.)

Depending upon use,a9Vlithium battery can be expected to last for

two to three years before replacement is required.

Flush Operations

The exposed electronic valve provides the following ﬂushing

operations:

Wave activated main ﬂush operation: When a hand is waved

over the sensor, the valve provides a main ﬂush.

Automatic 24-hour ﬂush operation: After 24-hours of non-use,

the valve produces a full ﬂush.

Low Battery Indication

The 9 V lithium battery can be expected to last for two to three years

before replacement is required. When the battery reaches a certain

point in its lifetime, the valve announces the low battery condition by

continuously ﬂashing an LED whenever a user is in range. The battery

is easily replaced as described in the section ″Replace the Battery″in

this guide.

Replacement batteries can be purchased from drugstores or other stores

stocking batteries. The required battery is a standard 9 V lithium.

Seasonal Use

The exposed electronic valve is not designed for operation in freezing

conditions. If freezing conditions are expected, isolate and drain the

valve along with whatever other winterization steps are taken for the

facility.

Mobile Use

The exposed electronic valve is not designed for use in moving

environments such as boats.

Care and Cleaning

For best results, keep the following in mind when caring for your

KOHLER product:

•Use a mild detergent such as liquid dishwashing soap and warm

water for cleaning. Do not use abrasive cleaners that may scratch

or dull the surface.

Kohler Co. 5 1108709-5-E

Care and Cleaning (cont.)

•Carefully read the cleaner product label to ensure the cleaner is

safe for use on the material.

•Always test your cleaning solution on an inconspicuous area

before applying to the entire surface.

•Do not allow cleaners to sit or soak on the surface.

•Wipe surfaces clean and rinse completely with water immediately

after cleaner application. Rinse and dry any overspray that lands

on nearby surfaces.

•Use a soft, dampened sponge or cloth. Never use an abrasive

material such as a brush or scouring pad to clean surfaces.

For detailed cleaning information and products to consider, visit

www.kohler.com/clean. To order Care & Cleaning information, call

1-800-456-4537.

1108709-5-E 6 Kohler Co.

Control Stop Valve Operation

NOTICE: Refer to this section throughout the Maintenance Guide

when instructed to close and open the control stop valve.

General Adjustment Instructions

Use a strap wrench to remove the vandal-resistant cap from the

control stop valve.

Close the stop valve by turning the valve screw clockwise as far

as it can go.

Open the stop valve by turning the valve screw counterclockwise

as far as it can go.

When done, place the stop cap on the control stop valve and

tighten using a strap wrench.

Control Stop Adjustment

NOTE: To adjust the control stop to achieve peak performance of 25

gpm (95 lpm) perform the steps below.

Use a strap wrench to remove the vandal-resistant cap from the

control stop valve.

Close the control stop (clockwise) all the way.

Open the control stop 1/4 turn (counterclockwise).

Test ﬂush the ﬁxture.

Repeat until excessive splashing occurs during the ﬂush.

Wall Flange

Wall Tube

Control Stop

Stop Cap

Kohler Co. 7 1108709-5-E

Control Stop Valve Operation (cont.)

If excessive splashing occurs during the test ﬂush, close the

control stop 1/4 turn.

Test ﬂush.

If splashing is at an acceptable level this is the optimal setting. If

excessive splashing occurs during the test ﬂush, close the control

stop another 1/4 turn and test.

Repeat until the optimal setting is found.

1108709-5-E 8 Kohler Co.

Remove the DC Sensor

Using a 3/32″hex head wrench, remove the setscrew from the

valve cap.

Remove the cap by carefully lifting from the valve body.

Disconnect the DC sensor connector to the solenoid by grasping

each side of the connector pair and pulling apart. Do not separate

the connector pair by pulling on the wires.

Position the cap on its side and look inside.

Remove the battery.

Remove the screws that hold the DC sensor in place inside the

cap.

Turn the cap over and slide the DC sensor, sensor strap, and

screws into your hand.

NOTE: The battery inside the sensor may be considered hazardous

waste. Discard the old DC sensor and/or battery in accordance with

any applicable codes.

If replacing the DC sensor, discard the old DC sensor and battery.

Cap

Setscrew

DC Sensor

Connector

Sensor Strap

Screw

Kohler Co. 9 1108709-5-E

Replace the Battery

NOTE: When purchasing a replacement battery, selecta9Vlithium

battery.

NOTE: It is not necessary to remove the sensor from the cap to

replace the battery.

Using a 3/32″hex wrench, remove the setscrew from the cap.

Remove the cap.

Using a small, ﬂat-blade screwdriver (if necessary), carefully pry

the battery from the cap.

Disconnect the battery and remove the battery boot.

NOTE: The battery may be considered hazardous waste. Discard

the old battery in accordance with any applicable codes.

Discard the old battery.

Connect the new battery. Install the battery boot over the

connections.

Reinstall the battery into the cap.

Reinstall the cap.

Battery

Setscrew

Battery Boot

Cap

1108709-5-E 10 Kohler Co.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Unidad de control de Kohler

Kohler

Kohler DTV+ Konnect K-97999-NA Manual de usuario

Kohler

Kohler 28209W-NA Manual de usuario

Kohler

Kohler K-2975 Manual de usuario

Kohler

Kohler 880A Manual de usuario

Kohler

Kohler K-682 Manual de usuario

Kohler

Kohler TOUCHLESS K-13686 Manual de usuario

Kohler

Kohler AQUA TURBO 360 Manual de usuario

Kohler

Kohler K-304 Instrucciones de montaje

Kohler

Kohler K-728 Instrucciones de montaje

Kohler

Kohler TAUT 73193T-4CD Manual de usuario

Kohler

Kohler K-407 Manual de usuario

Kohler

Kohler 5-10EKD Manual de usuario

Kohler

Kohler K-306 Manual de usuario

Kohler

Kohler GM77177-KP1-QS Manual de usuario

Kohler

Kohler K-305 Instrucciones de montaje

Kohler

Kohler K-2977 Instrucciones de montaje

Kohler

Kohler K-T10669 Instrucciones de montaje

Kohler

Kohler K-402 Instrucciones de montaje

Kohler

Kohler K-175 Instrucciones de montaje

Kohler

Kohler K-400 Manual de usuario

Kohler

Kohler BEAM K-77691K-G Manual de usuario

Kohler

Kohler K-402 Manual de usuario

Kohler

Kohler K-10675 Manual de funcionamiento

Kohler

Kohler K-10959 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario