Kohler K301 Manual de usuario

Installation Guide

3/4″High-Flow Deck/Rim Mount Bath Valve

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-301

113969-2-AC

Tools and Materials

Thank You For Choosing Kohler Company

Thank you for choosing Kohler Company. Your Kohler Company

product reﬂects the true passion for design, craftsmanship, artistry, and

innovation Kohler Company stands for. We are conﬁdent its

dependability and beauty will surpass your highest expectations,

satisfying you for years to come.

All the information in this guide is based upon the latest product

information available at the time of publication. At Kohler Company,

we strive to fulﬁll our mission of improving the level of gracious living

for each person who is touched by our products and services. We

reserve the right to make changes in product characteristics, packaging,

or availability at any time without notice.

Please take a few minutes to review this guide. If you encounter any

installation or performance problems, please call 1-800-4KOHLER

(1-800-456-4537) from within the USA and Canada, or 001-877-680-1310

from within Mexico.

Before You Begin

Observe all local plumbing and building codes.

Shut off the water supply.

Assorted

Screwdrivers

Adjustable

Wrench

Pipe

Wrench

Strap

Wrench Hacksaw or

Tubing Cutter

Propane

Torch

Solder

Thread

Sealant

Plumbers

Putty

Plus:

• Wood Screws

• Rags

113969-2-AC 2 Kohler Co.

Before You Begin (cont.)

Instructions are given for installations with 8″(20.3 cm) centers.

For wider installations, adjust all roughing-in dimensions and

copper tube lengths accordingly. If the spout is to be installed

more than 24″(61 cm) from the valves, Kohler recommends

installing a Sioux Chief 652-AD water hammer arrestor designed

for this type of installation. Install the water hammer arrestor

close to the outlet ports of the valves. For more information

contact Sioux Chief at www.siouxchief.com.

Products purchased separately may change valve placement and

alignment.

These instructions cover two methods of installation: installation

on ﬁnished deck or rim, and installation on rough (unﬁnished)

deck. Follow the sections and directions that pertain to your

installation.

Provide an access panel to the valves for servicing.

Installer-supplied copper tubing is to be: 5/8″OD (1/2″Nom.);

and 7/8″OD (3/4″Nom.) for inlets.

Plaster guard diameters are approximately 1-5/8″(4.1 cm) for the

valve, and 7/8″(2.2 cm) for the spout.

The ﬁnished deck material must ﬁt closely to the diameters of the

plastic guards.

The spout plaster guard diameter is 7/8″(2.2 cm) for the spout.

Leave the protective sleeve on the spout supply tube until spout

installation. This is an O-ring sealing surface which may be

damaged when unprotected.

Kohler Co. reserves the right to make revisions in the design of

faucets without notice, as speciﬁed in the Price Book.

Kohler Co. 3 113969-2-AC

1. Prepare the Site

X=the distance from the centerline of the spout inlet base to the

front of the spout base plus 1/2″(2.5 cm).

Y=the distance between the valve centerlines varies. Check the

handle and spout installation instructions for exact dimensions.

Install or relocate the water supplies as needed.

Protect the surfaces of the bath/deck during installation.

Ensure that holes drilled into the deck are not oversized. The

spout and valves require adequate base material strength and

maximum contact area with the deck.

NOTE: Reinforcing material may be required if the deck or rim is

thin. Install 1/2″exterior grade plywood before proceeding.

NOTE: For installations to be covered with tile, the tile thickness

must not exceed 1-1/4″(3.2 cm).

For installations with 8″(20.3 cm) centers using copper tubing

(1/2″nominal, 5/8″OD), cut two 2-7/8″(7.3 cm) pieces and one

2-3/8″(6 cm) piece of tubing.

1-1/4" (3.2 cm) Max.

Tile Thickness

7/8" D.

5/8" O.D. Tubing (1/2" Nom.)

1-5/16" D.

7/8" D.

1-5/16" D.

Finished Deck And Rim Mount Roughing-In

Rough Deck Plus Finished Deck (Tile) Roughing-In

1/8" (3 mm) Min.

2-1/8" (5.4 cm) Max.

Rim Thickness

7/8" I.D.

(3/4" Nom.)

1/2" (1.3 cm) Min.

2-1/8" (5.4 cm) Max.

Deck Thickness

1-13/16"

(4.6 cm)

4-5/8"

(11.7 cm)

5-5/8"

(14.3 cm)

2-1/16"

(5.2 cm)

1/2" (1.3cm) Min.

2-1/8" (5.4 cm) Max.

Rough Deck

Thickness

5/8" O.D. Tubing

(1/2" Nom.)

7/8" I.D.

(3/4" Nom.)

113969-2-AC 4 Kohler Co.

Prepare the Site (cont.)

The diameter of the spout hole should be 1-1/8″(2.9 cm)

maximum.

The diameter of the valve holes should be 1-1/2″(3.8 cm)

maximum.

Kohler Co. 5 113969-2-AC

2. Install the Spout Supply Tube

NOTE: Leave the protective sleeve on the spout supply tube until

the spout installation.

Slide the brass washer from the bottom of the spout supply tube

over the threads until it reaches the spout supply shoulder.

Insert the spout supply tube through the mounting hole from the

top of the deck/bath rim.

The ﬂat portion of the brass washer should face forward, and the

countersunk holes should face up. The spout supply tube will be

suspended by the brass washer.

Slide the plate (oriented with the tabs toward the deck) and

washer onto the spout supply tube from the bottom and thread

on the nut.

Tighten the nut.

Secure the plate to the rough deck with two wood screws.

Brass

Washer

Plate

Washer

Wood

Screw

Wood

Screw

Nut

Spout Supply Tube

Spout

Supply

Shoulder

113969-2-AC 6 Kohler Co.

3. Install the Valves

IMPORTANT! Do not solder the connections during this step.

Thread one mounting nut, ﬂange side up, followed by one ﬁber

washer and one rubber washers onto each valve body.

Insert the 2-7/8″(7.3 cm) long copper tubes between the valve

bodies and 1/2″tee.

For a ﬁnished deck or bath rim installation only, insert the 2-3/8″

(6 cm) long copper tube into the top of the tee.

NOTE: Orient the valve body marked “COLD” so it is on the right

when facing the front of the faucet.

Insert the valve bodies through the mounting holes from the

bottom of the deck/rim.

Hold the tube in place.

Place a collar, ﬂange side up, on each valve body and thread

them down to at least 1-13/16″(4.6 cm) from the top of the valve

stem.

2-7/8" (7.3 cm)

Copper Tubes

1/2"

Tee

2-3/8" (6 cm) Copper

Tube (Finished Deck

or Bath Rim

Installation Only)

Rubber

Washer

Fiber

Washer

Mounting

Nut Valve Body

1-13/16"

(4.6 cm)

Collar

Valve Stem

Kohler Co. 7 113969-2-AC

4. Installation on Finished Deck or Rim

NOTE: For installation on a rough (unﬁnished) deck, proceed to the

″Installation on Rough (Unﬁnished) Deck″section.

Tighten the mounting nuts on each valve body from underneath

the deck/rim.

Solder the copper tubes to the valve bodies, tee and spout supply

tube.

Solder the hot and cold water tubes to the valve body inlets (not

shown). Make sure that the cold supply is on the right side.

Go to the ″Check Operation of Valves″section.

Hot

Supply

Solder

Cold

Supply

Collar

Mounting

Nut

113969-2-AC 8 Kohler Co.

5. Installation on Rough Deck

When the tile or deck material is less than 1” (2.5 cm) thick:

Add the thickness of the tile/deck material to 2-1/16″(5.2 cm) to

get the installation height for the valve bodies.

Deck Material+ 2-1/16″(5.2 cm) =Installation Height

Note this dimension. You will need to use it again after

connecting the supply tube.

Adjust the threaded collar until the dimension from the top of the

valve stem to the top of the rough deck surface equals the

determined clearance.

When the tile or deck material is between 1” (2.5 cm) to 1–1/4” (3.2

cm) thick:

Thread the collar down onto each of the valve bodies until the

top of the valve stem is 3-1/16″(7.8 cm) above the surface of the

rough deck.

3–1/6" (7.8 cm)

Valve Body

Clearance

Deck thickness

between 1" (2.5 cm)

and 1–1/4" (3.2 cm)

Threaded

Collar

Top of Valve Stem

Calculated

Valve Body

Clearance

Deck thickness less

than 1" (2.5 cm)

Rough Unfinished

Deck 2-1/8" (5.4 cm)

Max.

2-1/16"

(5.2 cm)

Kohler Co. 9 113969-2-AC

6. Install the Tubing - Rough Deck Installations

Measure the distance from the bottom of the spout supply tube to

the top of the tee.

Add 1″(2.5 cm) to this measurement, and cut a piece of 1/2″

Nom. (5/8″O.D.) copper tubing to ﬁt into the supply tube and

tee port.

Back off the threaded collars as far as possible without removing

them.

Pivot the valve bodies enough to remove the tee and two pieces

of tubing.

NOTE: If the valve body holes are smaller than recommended, it

may be necessary to remove the entire valve body assembly.

Install the tubing into the tee.

Mate the copper tube from the tee with the spout supply tube.

Pivot the valve bodies onto the two pieces of copper tubing.

DO NOT solder at this time.

Tee Measure

Distance

Spout Supply

Tube

Tee

Copper

Tube

Mounting

Nut

Rough

Deck

Sleeve

Spout Supply

Tube

Threaded

Collar

113969-2-AC 10 Kohler Co.

Tabla de contenidos

Idiomas:

Otros manuales de Unidad de control de Kohler

Kohler

Kohler K-2971 Manual de usuario

Kohler

Kohler K-402 Manual de usuario

Kohler

Kohler K-10675 Manual de usuario

Kohler

Kohler 28139T-DR Manual de usuario

Kohler

Kohler K-528 Manual de usuario

Kohler

Kohler 880A Manual de usuario

Kohler

Kohler Mastershower K-406 Manual de usuario

Kohler

Kohler rada VZ1 10 Manual de usuario

Kohler

Kohler K-407 Manual de usuario

Kohler

Kohler K-306 Manual de usuario

Kohler

Kohler K-728 Instrucciones de montaje

Kohler

Kohler K-8548 Manual de usuario

Kohler

Kohler K-5557 Instrucciones de montaje

Kohler

Kohler K-14677 Instrucciones de montaje

Kohler

Kohler ENGLEFIELD K-98095X Instrucciones de montaje

Kohler

Kohler Rite-Temp K-8304-K Manual de usuario

Kohler

Kohler K-682 Manual de usuario

Kohler

Kohler K-528 Manual de usuario

Kohler

Kohler K-305 Instrucciones de montaje

Kohler

Kohler K-10956 Manual de funcionamiento

Kohler

Kohler K-10949 Manual de usuario

Kohler

Kohler K-13516X Instrucciones de montaje

Kohler

Kohler AQUA TURBO 360 Manual de usuario

Kohler

Kohler DTV+ Konnect K-97999-NA Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario