Kogan KAWLM70TLTA Manual de usuario
PREMIUM TILT EXTENDABLE
FULL MOTION WALL MOUNT
(32"-70")
KAWLM70TLTA
•Please closely follow the assembly instructions. Improper installation may result in
damage or serious personal injury.
•Safety gear and quality tools must be used.
•This product is suitable for installation on solid concrete walls, masonry walls or
wood stud walls.
•Make sure that the supporting surface will safely support the combined weight of
the equipment and all attached hardware and components.
•Use the mounting screws provided and DO NOT OVER TIGHTEN mounting
screws.
•Do not allow children to play near this stand.
•This product contains small items that could be a choking hazard if swallowed.
Keep these items away from children.
•This product is intended for indoor use only. Using this product outdoors could lead
to product failure and personal injury.
•A minimum of two people are recommended for this installation. Failure to use
safety gear and safe working methods may result in property damage, serious
injury or death.
IMPORTANT: Ensure that you have received all parts according to the component checklist
prior to installation. If any parts are missing or faulty, contact your place of purchase for a
replacement.
MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at
least every three months).
VESA compatibility:
200x200, 300x200, 300x300
400x200, 400x300, 400x400
CAUTION:
Rated weight is 45kg (99 lbs).
Use with products heavier than the rated weights indicated may result
in instability causing possible injury.
Suitable for TVs 32” - 70” maximum
SAFETY & WARNINGS
Wall mount assembly:
A(x1)
B(x1)
C(x2)
D(x4)
E4mm (x1)
F(x1)
W-A ST8x90 (x5)
W-B Ø12x60 (x5)
W-C (x4)
Adapters (depends on TV):
M-A M5x14 (x4)
M-B M6x14 (x4)
M-C M6x30 (x4)
M-D M8x30 (x4)
M-E M8x50 (x4)
M-F D5 (x4)
M-G D8 (x4)
M-H (x8)
M-I (x8)
Additional Tools Required (Not Supplied):
Phllips head
screwdriver
Stud finder
Spirit level
Pencil
Electric drill
Socket wrench
COMPONENTS
Step 1: Getting started
Pull the extendable arms out away from the base, then remove the base cover.
A minimum of two people are recommended for this installation. Failure to
use safety gear and safe working methods may result in property damage,
serious injury, or death.
ASSEMBLY
Step 2: Drywall, plaster or timber walls (with studs)
Use a stud finder to locate safe and suitable locations to install into wall. Use a spirit level to
double check the correct angle of the mount and mark the intended hole positions with a
pencil (2a). When installing on a drywall, plaster or timber wall, refer only to the centre holes
of the mount. Drill holes in the desired locations (90mm deep, 6mm wide) (2b).
Insert the top screw (W-A) first, to support the mount (2c). With the wall mount held in place,
insert the washers and screws (W-C, W-A), tightening with a socket wrench (2d). When
installing on a drywall, plaster or timber wall, do not use the screw anchors (W-B).
A minimum of two people are recommended for this installation. Failure
to use safety gear and safe working methods may result in property
damage, serious injury, or death.
Step 2: Concrete and masonry walls
Use a spirit level to double check the correct angle of the mount and mark the intended hole
positions with a pencil (2b). Drill holes in the desired locations (95mm deep, 12mm wide) (2b).
Insert the screw anchors (W-B) into each pre-drilled hole, then insert the top screw (W-A) first
to support the mount (2c). With the wall mount held in place, insert the washers and screws
(W-C, W-A), tightening with a socket wrench (2d).
A minimum of two people are recommended for this installation. Failure
to use safety gear and safe working methods may result in property
damage, serious injury, or death.
Step 3: Once the wall mount is secured in place, the base cover can be replaced.
Step 4: Set the mounting brackets for your required VESA configuration
400mm
300mm
200mm
Step 5: Attaching the mounting brackets to your TV.
Depending on your TV, a combination of spacers (M-H, M-I) may be required to help create
the correct amount of space for the brackets. Ensure the screws are fitted correctly into your
TV’s VESA mount holes, and are not too long or too short in the back of the TV.
Ensure washers and screws are aligned in the
centre of opening. Do not install with washers and
screws off to either side.
Tabla de contenidos
Otros manuales de Rack y soporte de Kogan
Kogan
Kogan KATVSTHLDCA Manual de usuario
Kogan
Kogan KASLSTMTSTA Manual de usuario
Kogan
Kogan OSTIA Series Manual de usuario
Kogan
Kogan KAWLM82TEXA Manual de usuario
Kogan
Kogan KAWLM85TSMA Manual de usuario
Kogan
Kogan KATVBKSTNDA Manual de usuario
Kogan
Kogan KAWLM90FIXT Manual de usuario
Kogan
Kogan KATVCST65LM Manual de usuario
Kogan
Kogan KASTTVPB55A Manual de usuario
Kogan
Kogan KAWLM90TSMT Manual de usuario
Kogan
Kogan KASMM39S12A Manual de usuario
Kogan
Kogan KAWLM70CNRA Manual de usuario
Kogan
Kogan OSTIA Series Manual de usuario
Kogan
Kogan PS5 Manual de usuario
Kogan
Kogan KATVBKSTNDA Manual de usuario
Kogan
Kogan KAWLM55TEXA Manual de usuario
Kogan
Kogan KAWLMFM55MA Manual de usuario
Kogan
Kogan KAWLMSBMNTA Manual de usuario
Kogan
Kogan LARVIK STUDIO STAND Manual de usuario
Kogan
Kogan KAWLMSBMNTA Manual de usuario
