Kogan KASTTVPB55A Manual de usuario
PORTABLE TV MOUNT
STAND CART
(32" - 55")
KASTTVPB55A
CAUTION:
Rated weight for the TV stand is 33kg (77 lbs). The rated weight for the storage shelf
is 5kg (11 lbs).
Use with products heavier than the rated weights indicated may result in instability
causing possible injury.
•Please closely follow the assembly instructions. Improper installation may result in
damage or serious personal injury.
•Safety gear and quality tools must be used.
•When in use, make sure the stand is on a flat level surface and the caster wheels
are locked.
•Do not allow children to play near this stand.
•This product contains small items that could be a choking hazard if swallowed.
Keep these items away from children.
•This product is intended for indoor use only. Using this product outdoors could lead
to product failure and personal injury.
•A minimum of two people are recommended for this installation. Failure to use
safety gear and safe working methods may result in property damage, serious
injury or death.
IMPORTANT: Ensure that you have received all parts according to the component checklist
prior to installation. If any parts are missing or faulty, contact your place of purchase for a
replacement.
MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at
least every three months).
VESA compatibility:
100x100, 200x100, 200x200, 300x200, 300x300, 400x200, 400x300, 400x400
Suitable for TVs 32” – 55” maximum
SAFETY & WARNINGS
Stand assembly:
A(x1)
B(x2)
C(x1)
D(x1)
E(x1)
F(x1)
G(x1)
H(x1)
I(x1)
J(x4)
K(x1)
L(x1)
M(x2)
NM6x50 (x4)
OM6x35 (x4)
PM6x16 (x11)
Q(x8)
R(x1)
S(x1)
T(x1)
Adapters (Depends on TV):
M-A M5x14 (x4)
M-B M6x14 (x4)
M-C M6x30 (x4)
M-D M8x30 (x4)
M-E M8x50 (x4)
M-F (x4)
M-G (x8)
M-H (x8)
COMPONENTS
Step 1: Assembling the base
Attach the cross-beam (C) to the two base beams (B), using the Allen key (S) to tighten the
M6x16mm (P) and M6x35mm (O) screws in place as shown below.
After the cross-beam is secured, attach the locking caster wheels (J), using the spanner (T)
to tighten. Once the casters are installed, clamp the locks down to ensure the stand does
not move suddenly during the remainder of the assembly. Place the joint left and right joint
covers (K, L) into position as shown below.
ASSEMBLY
Unlock
Lock
Step 2: Attaching the stand
Place the stand (A) and joint cover (I) into position on the cross-beam, securing it with x4
washers (Q) and M6x50mm screws (N). Use the Allen key (S) to tighten.
Warning: To adjust the height, pull
the safety spring lock outwards (1)
while pulling the column upward
(2) at the same time. Always
ensure the spring lock aligns with
the keyhole, otherwise a sudden
drop may occur resulting in injury
or property damage.
Note: The MAX line found on the
column indicate the highest
position. Never go beyond the
MAX line marking.
Step 3:
Insert the supporting M6x16mm screw (P) into the extended stand, tightening it with the
Allen key. Insert the hole covers (R, M) in place.
Step 4:
Attach the mounting plate (D) to the front of the stand, securing it with x4 washers (Q) and
M6x16mm screws (P), using the Allen key to tighten.
Step 5:
Attach the shelf (G) to the stand, securing it to the shelf mount (H) with M6x16mm screws
(P). The shelf is suitable for use with laptops, DVD and Blu-ray players, hard drives, gaming
consoles, or anything else as long as the weight limit (5 kg) is not exceeded.
Step 6:
Attach the mounting brackets to your TV. Depending on your TV, a combination of spacers
(M-G, M-H) may be required to help create the correct amount of space for the brackets.
Ensure the screws are fitted correctly into your TV’s VESA mount holes, and are not too long
or too short in the back of the TV.
Also note that the M-F adapter is used for both small screws (M-A, M-B) and large screws
(M-C, M-D, M-E) depending on its orientation.
Step 7:
NOTE: Ensure the locking caster wheels (J) are locked before attempting to mount the TV.
With two people, lift the TV up and above the mounting plate and gently lower down into
place, ensuring the TV is evenly positioned in the middle of the stand.
The brackets each feature a vertical screw to secure to the bottom of the mount. Hook this
screw underneath the mount and tighten to secure.
A minimum of two people are recommended for this installation.
Failure to use safety gear and safe working methods may result in
property damage, serious injury, or death.
Tabla de contenidos
Otros manuales de Rack y soporte de Kogan
Kogan
Kogan KATVBKSTNDA Manual de usuario
Kogan
Kogan OSTIA Series Manual de usuario
Kogan
Kogan KASMM39S12A Manual de usuario
Kogan
Kogan KAWLMFX75MA Manual de usuario
Kogan
Kogan KAWLM70CNRA Manual de usuario
Kogan
Kogan KAWLM90TSMT Manual de usuario
Kogan
Kogan PS5 Manual de usuario
Kogan
Kogan KALTHDSTVSA Manual de usuario
Kogan
Kogan KAWLM90FIXT Manual de usuario
Kogan
Kogan KATVBKSTNDA Manual de usuario
Kogan
Kogan KASMM39S24A Manual de usuario
Kogan
Kogan LCDP30 Manual de usuario
Kogan
Kogan KAWLM70TLTA Manual de usuario
Kogan
Kogan KATVBKSTNDA Manual de usuario
Kogan
Kogan KAWLM82TEXA Manual de usuario
Kogan
Kogan KAWLM55CNRA Manual de usuario
Kogan
Kogan LARVIK STUDIO STAND Manual de usuario
Kogan
Kogan OSTIA Series Manual de usuario
Kogan
Kogan KATVSTHLDCA Manual de usuario
Kogan
Kogan KAMMFS12DA Manual de usuario
