Kimo CO 110 Manual de usuario

COmeter

CO 110

DESCRIPTION OF THE DEVICE



OK key

Backlight key

Select key

On/Off/Esc key

Hold/min/max key

PERFORM A MEASUREMENT

➢Turn on the device by pressing on “On/Off/Esc”

The device displays its name “CO 110” then performs an autozero during 5 seconds.

The probe must be left to the open-air during this autozero.

➢Put the probe to the required location

The device displays the CO and temperature measurements.

FREEZE THE MEASUREMENT

During the measurement:

➢Press “Hold/min/max” to freeze the measurement

“Hold” appears on the screen and the measurements are frozen.

➢Press “On/Off/Esc” to exit the hold function

The device returns to the measurements display.

DISPLAY THE MINIMUM AND THE MAXIMUM

Once the measurements are frozen:

➢Press “Hold/min/max”

The device displays the maximum value of CO measured since the last questioning at the top of the screen and the minimum value of CO

measured since the last questioning at the bottom of the screen.

➢Press again “Hold/min/max”

The device displays the maximum value of temperature measured since the last questioning at the top of the screen and the minimum value

of temperature measured since the last questioning at the bottom of the screen.

➢Press “On/Off/Esc” to return to the measurements display



ADJUST THE DEVICE

Select the measuring unit in temperature

➢Press “Select”

“UNIT” blin s on screen.

➢Press “OK”

The unit currently used blin s at the bottom of the screen.

➢Press “Select” until the required unit appears: °C or °F

➢Press “OK” to validate

“UNIT” blin s on screen.

➢Press “On/Off/Esc” to return to the measurements display

Adjust the auto shut-off

The device is on and displays the measurements.

➢Press “Select” until “A TO OFF” blinks on screen

➢Press “OK”

The time before device auto shut-off blin s on screen.

➢Press “Select” to select the time before device auto shut-off: 15, 30, 45, 60, 75, 90, 105, 120 or OFF

➢Press “OK” to validate

➢“ UTO OFF” blin s on screen.

➢Press “On/Off/Esc” to return to the measurements display

Device drop-down menu

AUTO

OFF

SEL.

AUTO

OFF

Select OK

AUTO

OFF

15 / 30mn

Select

On/Off/

Esc

SEL.

AUTO

OFF

30mn

0.2

PPm

20.5

°C

During the measurement:

➢Press “OK”

“CO M X” displays on screen with below the measuring time to adjust. This time is between 0:00 and 5:00.

➢Press “Select” to adjust the first digit then “OK” to validate, perform the same procedure for the following digits

➢When the fist digit is adjusted, press “OK”

“ST RT” displays on screen.

➢Press again “OK” to start the measuring time

The device displays the measuring time count. At the end of this count, the CO max measurement displays on screen.

PERFORM A CO MAX MEASUREMENT

1x Select UNIT

SEL.

C° / F°

SEL.

UNIT

C°

UNIT

SEL.

C°

Select

0.2

PPm

20.5

°C

On/Off/

Esc

SEL.

UNIT

C°

Select

1x 2x 3x 4x

SEL.

AL 1

OFF

PPm

SelectSelect

SEL.

BEEP

Select

SEL.

AUTO

OFF

SEL.

UNIT

C°

On/Off/

Esc

SEL.

AL 2

OFF

PPm

Adjust the alarms

The device is on and displays the measurements.

It's possible to adjust 1 or 2 alarms which will be triggered when the alarm threshold has been reached and/or exceeded. This threshold is

between 0 and 500 ppm.

➢Press “Select” until “AL 1” blinks on screen “AL 1” corresponds to the level 1 alarm

➢Press “OK”

The first alarm digit blin s.

➢Press “Select” to select the first digit value: between 0 and 5 or OFF to deactivate the alarm

➢Press “OK” to validate and to pass to the following digit, perform the same procedure for the following digits (press “On/Off/Esc” to

return to the previous digit)

➢Press “OK” when the last digit is adjusted

“L 1” blin s on screen.

➢Press “On/Off/Esc” to return to the measurement display

➢To adjust the level 2 alarm, press “Select” until “AL 2” blinks on screen then follow the same procedure as the adjustment of the level 1

alarm

Activate or deactivate the keys beep

The device is on and displays the measurements.

➢Press “Select” until “BEEP” blinks on the screen

➢Press “OK”

“ON” or “OFF” blin s on the screen.

➢Press “Select” to activate the keys beep “ON” or deactivate the keys beep “OFF”

➢Press “OK”

➢“BEEP” blin s on the screen.

➢Press “On/Off/Esc” to return to the measurement display

SEL.

BEEP

SEL.

SelectSelect

SEL.

BEEP

OFF

On/Off/

Esc

0.2

PPm

20.5

°C

BEEP

SEL.

OFF / ON

ACTIVATE THE BACKLIGHT

The device is on and displays the measurements.

➢Press “Backlight” to activate the device backlight

➢To deactivate it press again “Backlight”

➢Remove the front part at the back of the device

➢Change the old batteries by AAA LR03 1 5 V batteries

➢Replace the front part

CHANGE THE BATTERIES

NTang – portable-CO110 – 10/11/17 – RCS (24) Périgueux 349 282 095 Non-contractual document – We reserve the right to modify the characteristics of our products without prior notice

Once returned to KIMO, required waste collection will be assured in the respect of the environment in accordance to 2002/96/CE guidelines relating to WEEE

Tabla de contenidos

Otros manuales de Instrumento de medición de Kimo