Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV... Manual de usuario

Juniper Networks, Inc.

1194 North Mathilda Avenue

Sunnyvale, CA 94089

USA

408-745-2000

www.juniper.net

Part Number: 530-025620-01, Revision 1

Security Threat Response Manager

Getting Started With STRM Appliances

Release 2008.2

2

Networks Inc. in the United States and other countries. All other trademarks, service marks, registered trademarks, or registered service marks in this

document are the property of Juniper Networks or their respective owners. All specifications are subject to change without notice. Juniper Networks

assumes no responsibility for any inaccuracies in this document or for any obligation to update information in this document. Juniper Networks reserves

the right to change, modify, transfer, or otherwise revise this publication without notice.

FCC Statement

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. The equipment generates, uses, and can radiate radio-frequency energy and, if not installed and

used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense. The following

information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it

is not installed in accordance with NetScreen’s installation instructions, it may cause interference with radio and television reception. This equipment has

been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These

specifications are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Consult the dealer or an experienced radio/TV

technician for help. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

Caution: Changes or modifications to this product could void the user's warranty and authority to operate this device.

Disclaimer

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET

THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE

SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR JUNIPER NETWORKS REPRESENTATIVE FOR A COPY.

Getting Started With STRM Appliances

Release 2008.2

Revision History

June 2008—Revision 1

The information in this document is current as of the date listed in the revision history.

CONTENTS

Before You Begin 1

STRM Appliance Installation and Configuration 3

QFlow Installation and Configuration 8

Before You Begin Before performing these procedures, you must have access to the following:

•Hardware Requirements — You must have access to a hard drive, monitor,

keyboard, and mouse to log in to the application.

•Java Requirements — You must install Java version 1.5.0_12. For more

information see http://java.com/.

•Browser Requirements — You must have Internet Explorer 6.0/7.0 or Firefox

2.0.

Warning: Before performing these procedures, see the safety instructions and

important regulatory information in your QRadar Installation Guide and the

Hardware Installation Guide.

Note: The graphics in this guide are representations of a QRadar appliance. Your

appliance may vary, depending on the version of QRadar or QFlow appliance you

have purchased. See the QRadar Installation Guide.

Note: When using a laptop to connect to the appliance you must use a terminal

program, such as HyperTerminal, to connect to the appliance. Be sure to set

Connect Using to the appropriate COM port of the serial connector and Bits per

second to 9600. You must also set Stop Bits (1), Data bits (8), and Parity

(None).

STRM Appliance Installation and Configuration

Unpack Your Appliance

Save all shipping materials in case you need

them later. (Your appliance may not include all

accessories shown.)

Install the Appliance in a Rack

See the Hardware Installation Guide for

instructions on installing your appliance in a

rack.

Connect to External Devices

Connect external devices using the ports on the

rear of the appliance. If you are using a monitor

with a keyboard, tighten the screws on the

monitor’s cable connector. You must use a USB

keyboard or a PS2 to USB adapter. If you use a

laptop, connect the laptop to the serial connector

on the rear of the appliance.

Connect to the Network

Connect the appliance to your network using the

ports on the rear of the appliance. The

Management Interface is the communications

port for your appliance; the Monitoring Interfaces

allow you to connect to span ports or taps.

If you wish to connect to a tap, see your tap

vendor documentation.

Connect to Power Source

Connect the power cable(s) to the appliance.

Next, plug the other end of the cable into a

grounded outlet on a separate power source,

such as an Uninterruptible Power Supply (UPS)

or a Power Distribution Unit (PDU). Connect the

monitor’s (or laptop) power cable to a grounded

electrical outlet.

4Monitoring Interface (ETH3)

Monitoring Interface (ETH2)

Monitoring Interface (ETH1)

Management Interface (ETH0)

Turn on the Appliance

Press the power button on the appliance and the

monitor or laptop. The power indicators should

light. Install the bezel after turning on the

appliance.

When the prompt appears, you are ready to log

in.

Using the keyboard with monitor or laptop, log in using the default username and password.

Note: Username and password are case sensitive.

Username: root

Password: password

Press Enter. The End User Licensing Agreement window appears.

Read the End User Licensing Agreement

Read the End User Licensing Agreement (EULA) information. Press the Spacebar to advance to each

window until you have reached the end of the document. Type yes to accept the agreement. Press

Enter. The Activation Key window appears.

Enter Your Activation Key

The activation key is a 24-digit four-part

(separated by hyphens) alphnumeric string that

you receive from Juniper Networks. Press Next.

The Tuning Template window appears.

Select a Tuning Template

Using the up/down arrow keys, select one of the

following templates to tune your appliance:

•Enterprise - Internal network activity.

•ISP - ISP-specific concerns.

•University - Education-specific concerns.

Using the left/right arrow keys, select Next.

Press Enter. The Set the Date and Time window

appears. For more information on templates, see

the STRM Administration Guide.

Choose How to Set Date and Time

Using the up/down arrow keys, select the

method you wish to use to set the date and time.

•Manual - Allows you to manually input the

date and time. Press the spacebar to select

and then press Enter to select Next. Go to

Step 12.

•Server - Allows you to specify your time

server. Press the spacebar to select and then

press Enter to select Next. Go to Step 13.

Enter the Date and Time

Enter the current date and time. Using the

left/right arrow keys, select Next. Press Enter.

The Time Zone window appears.

Go to Step 14.

Enter Time Server Name

In the text field, enter the time server name or IP

address. Using the left/right arrow keys, select

Next. Press Enter. The Time Zone Continent

window appears.

Configure Time Zone

aUsing the up/down arrow keys, or the page

up/page down keys, select your time zone

continent or area.

Using the left/right arrow keys, select Next,

then press Enter. The Time Zone Region

window appears.

bThe options appearing in this window are

regions associated with the continent or area

previously selected.

Using the up/down arrow keys, or the page

up/page down keys, select your time zone

region. Using the left/right arrow keys, select

Next. Press Enter. The Configure STRM

window appears.

Configure STRM Settings

Using the up/down arrow keys to navigate the

fields, update the following parameters:

•Hostname - Domain name as hostname.

•IP Address - IP address of the appliance.

•Netmask - Network mask address.

•Gateway - Default gateway.

•Primary DNS - Primary DNS server.

•Secondary DNS* - Secondary DNS server.

•Public IP* - Public IP address of the server.

•EMail Server - E-mail server. If you do not

have an e-mail server, enter localhost.

* All fields are mandatory with the exception of

the Secondary DNS and Public IP.

Press Tab and then, using the left/right arrow

keys, select Next. Press Enter. The New Root

Password window appears.

Configure Passwords

aEnter your root password. Use the TAB key to

navigate to the Next option. Press Enter. The

Confirm Password window appears.

bRe-enter your password to confirm. Use the

TAB key to navigate to the Finish option and

press Enter. When STRM completes the

installation process, the Configuration is

Complete window appears.

Finish Installation

Press Enter to select OK. Type exit and press

Enter.

Access STRM

aOpen your web browser.

bLog in to STRM:

https://<IP Address>

Where <IP Address>is the IP address of the STRM Console. The default values are:

Username: admin

Password: <your root password>

For your STRM Console, a default key provides you access to STRM for five weeks. For more

information on the license key, see the STRM Administration Guide.

cClick OK.

The STRM interface appears. You are now ready to start tuning STRM. For more information, see the

STRM Administration Guide.

QFlow Installation and Configuration

Unpack Your Appliance

Save all shipping materials in case you need

them later. (Your appliance may not include all

accessories shown.)

Install the Appliance in a Rack

See the Hardware Installation Guide for

instructions on installing your appliance in a

rack.

Connect to External Devices

Connect external devices using the ports on the

rear of the appliance. If you are using a monitor

with a keyboard, tighten the screws on the

monitor’s cable connector. You must use a USB

keyboard or a PS2 to USB adapter. If you use a

laptop, connect the laptop to the serial connector

on the rear of the appliance.

Connect to the Network

Connect the appliance to your network using the

ports on the rear of the appliance. The

Management Interface is the communications

port for your appliances; the Monitoring

Interfaces allow you to connect to span ports or

taps.

If you wish to connect to a tap, see your tap

vendor documentation.

Connect to Power Source

Connect the power cable(s) to the appliance.

Next, plug the other end of the cable into a

grounded outlet on a separate power source,

such as an Uninterruptible Power Supply (UPS)

or a Power Distribution Unit (PDU). Connect the

monitor’s (or laptop) power cable to a grounded

electrical outlet.

4Monitoring Interface (ETH3) Monitoring Interface (ETH2

Monitoring Interface (ETH1)

Management Interface (ETH0)

Otros manuales para SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV...

Este manual sirve para los siguientes modelos

Otros manuales de Software de Juniper

Juniper

Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV... Manual de usuario

Juniper

Juniper JUNOS 10.1 - S REV 4 Manual de instrucciones

Juniper

Juniper NETWORK AND SECURITY MANAGER - S REV 3 Manual de instrucciones

Juniper

Juniper JUNOSE SOFTWARE 11.2.X - BROADBAND ACCESS CONFIGURATION GUIDE... Manual de usuario

Juniper

Juniper NETWORK AND SECURITY MANAGER NSMXPRESS SERIES II - ... Manual de usuario

Juniper

Juniper JUNOSE 11.1.X - COMMAND REFERENCE A TO M... Manual de instalación

Juniper

Juniper IGP - CONFIGURATION GUIDE V11.1.X Manual de usuario

Juniper

Juniper JUNOSE SOFTWARE FOR E SERIES 11.3.X - BGP AND MPLS CONFIGURATION GUIDE... Manual de usuario

Juniper

Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING INTRUSION DETECTION PREVENTION DEVICES GUIDE REV... Manual de usuario

Juniper

Juniper JUNOSE SOFTWARE 11.0.1 - S 7-14-2010 Manual de instrucciones

Juniper

Juniper BXOS 4.1 R2 - S 07-2010 Manual de instrucciones

Juniper

Juniper JUNOS SPACE 2.0 - RELEASE NOTES Manual de instrucciones

Juniper

Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE... Manual de usuario

Juniper

Juniper JUNOSE 11.1.0 - REV 4-29-2010 Manual de usuario

Juniper

Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1 Manual de usuario

Juniper

Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE... Manual de usuario

Juniper

Juniper POLICY MANAGEMENT - CONFIGURATION GUIDE... Manual de usuario

Juniper

Juniper MEDIA FLOW PUBLISHER Manual de usuario

Juniper

Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV... Manual de usuario

Juniper

Juniper JUNOSE 10.0.X PHYSICAL LAYER Manual de usuario

Juniper

Juniper NETWORK AND SECURITY MANAGER - NSM CONFIGURATION GUIDE FOR EX SERIES DEVICES REV... Manual de usuario

Juniper

Juniper IP SERVICES - CONFIGURATION GUIDE V 11.1.X Manual de usuario

Juniper

Juniper JUNOSE SOFTWARE FOR E SERIES 11.3.X - BGP AND MPLS CONFIGURATION GUIDE... Manual de usuario

Juniper

Juniper JUNOSE SOFTWARE FOR E SERIES 11.3.X - POLICY MANAGEMENT CONFIGURATION GUIDE... Manual de usuario

Manuales populares de Software de otras marcas

COMPRO

COMPRO COMPROFM Manual de usuario

Muratec

Muratec OFFICEBRIDGE ONLINE Manual de usuario

Oracle

Oracle Contact Center Anywhere 8.1 Manual de usuario

Adobe

Adobe 65007312 - Photoshop Lightroom Manual

Avaya

Avaya NULL One-X for RIM Blackberry Manual de usuario

HP ProLiant BL420c Manual de usuario

PS Audio

PS Audio PowerPlay Manual del propietario

Brady

Brady LOCKOUT PRO 3.0 Manual de servicio

Avaya

Avaya Interaction Center Manual de usuario

Texas Instruments

Texas Instruments TI-83 Plus Silver Edition Manual

Novell

Novell GROUPWISE 8 - INTERNET AGENT Manual de usuario

Oracle

Oracle Application 9i Manual de usuario

Acer

Acer RDM Manual de usuario

Canon

Canon Vixia HF21 Manual de usuario

Canon

Canon ZR950 Manual de usuario

Samsung

Samsung Auto Backup Manual de usuario

Polycom

Polycom Vortex EF2201 Instrucciones de instalación y funcionamiento

Brocade Communications Systems

Brocade Communications Systems Brocade 8/12c Manual de usuario