Juniper NETWORK AND SECURITY MANAGER NSM3000

Network and Security Manager NSM3000

Quick Start

November 17, 2010

Revision 1

NSM3000 is an appliance version of Network and Security Manager (NSM). NSM3000

simplifies the complexity of network administration by providing a single, integrated

management interface that controls device parameters.

This robust hardware management system installs in minutes with full high availability

(HA) support, making it easy to scale and deploy. Enterprise customers with limited

resources can benefit significantly from NSM3000 because it eliminates the need to

have dedicated resources for maintaining a network and security management solution.

NSM3000 makes it easy for administrators to control device configuration, network

settings, and security policy settings for multiple families of Juniper devices including:

•IDP Series Intrusion Detection and Prevention Appliances and Firewall and VPN devices

running ScreenOS.

•Devices running Junos OS, such as J Series Services Routers, SRX Series Services

Gateways, EX Series Ethernet Switches, M Series Multiservice Edge Routers, and MX

Series Ethernet Services routers.

•SA Series SSL VPN Appliances

•IC Series Unified Access Control Appliances

For a complete list of supported device families and platforms, see the Network and

Security Manager Administration Guide.

Up to 10 administrators can log into NSM3000 concurrently.

This quick start explains the following steps for installing and configuring NSM3000 and

for configuring NSM.

1. Install the NSM3000 appliance hardware.

2. Set up the NSM3000 appliance, using the serial port.

3. Configure the NSM software, using the Web interface.

4. Configure the NSM software, which is preinstalled onto the NSM3000 appliance, with

site-specific parameters.

Contents HardwareInstallation.................................................4

NSM3000Ports.................................................4

InstallingtheNSM3000Hardware..................................5

InitialSetupConfiguration.............................................7

BootNSM3000..................................................7

SetUpYourAppliance............................................7

WebInterfaceConfiguration....................................8

ConfiguringtheNSMSoftware.........................................8

ConfiguringBasicSettings.........................................9

ConfiguringHighAvailability........................................11

AdvancedOptions...............................................14

Enabling and Configuring Remote Replication of the Database . . . . . . . 15

Enabling and Configuring the Statistical Report Server (SRS) (Regional

ServerOnly).............................................16

InstallingNSMSoftware..........................................17

ManagingNSMAdministration.........................................17

ChangingtheSuperuserPassword..................................17

Downloading NSM MIBS (Regional Server Only) . . . . . . . . . . . . . . . . . . . . . . . 18

ExportingAuditLogs.............................................18

Exporting Device Logs (Regional Server Only) . . . . . . . . . . . . . . . . . . . . . . . . . 18

Generating Reports (Regional Server Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

ModifyingNSMConfigurationFiles..................................19

BackingUptheNSMDatabase....................................20

ChangingtheNSMManagementIP.................................21

SchedulingSecurityUpdates......................................21

ManagingSystemAdministration......................................22

Rebooting or Shutting Down NSM3000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

ChangingtheUserPassword......................................23

ConfiguringtheNetwork..........................................23

NetworkInterfaces...........................................23

RoutingandGateways........................................24

HostnameandDNSClients...................................24

HostAddresses.............................................25

ManagingRADIUSServers........................................25

AddingaRADIUSServer......................................26

Changing the Priority of RADIUS Servers . . . . . . . . . . . . . . . . . . . . . . . . . 27

DeletingaRADIUSServer.....................................27

Editing RADIUS Server Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

MonitoringwithSNMP...........................................28

SNMPConfiguration.........................................28

SNMPSystemInformation....................................29

SNMPTrapConfiguration.....................................30

NSM3000 Quick Start

ForwardingSyslogMessages......................................31

ViewingSyslogReceivers......................................31

Adding and Configuring Syslog Receivers . . . . . . . . . . . . . . . . . . . . . . . . . 32

Editing Syslog Receiver Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

DeletingSyslogReceivers.....................................34

ChangingtheSystemTime.......................................34

InstallingUpdates...............................................34

ManagingUsers.................................................35

CreatingNewNSM3000Users.................................35

DeletingaUser..............................................37

EditingUserAttributes........................................37

UnderstandingUserProfiles...................................37

ConfiguringtheWebInterface.....................................39

Maintaining NSM3000 ..............................................39

ViewingSystemStatistics........................................39

CPU ......................................................40

LogRate...................................................40

CPULoad..................................................40

MemoryData...............................................40

Network Data ..............................................40

ProcessCount..............................................40

DiskData..................................................40

TileAllGraphs..............................................40

UpgradingtheRecoveryPartition...................................41

Troubleshooting ....................................................42

AuditingUserOperations.........................................42

Error Logs .....................................................43

NetworkUtilities................................................44

Ping ......................................................44

Traceroute .................................................45

Lookup....................................................46

IPSubnetCalculator.........................................46

TechSupport...................................................47

ViewingSystemInformation..........................................47

ListofTechnicalPublications.........................................48

RequestingTechnicalSupport........................................49

Self-Help Online Tools and Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

OpeningaCasewithJTAC........................................50

RevisionHistory.....................................................51

Hardware Installation

We recommend that you install NSM3000 on your LAN to ensure that it can communicate

with your applicable resources, such as authentication servers, DNS servers, internal Web

servers through HTTP/HTTPS, external Web sites through HTTP/HTTPS (optional), the

Juniper update server via HTTP, Network File System (NFS) file servers (optional), and

client/server applications (optional).

NOTE: If you decide to install NSM3000 in your DMZ, ensure that it can

connect to your internal resources.

NSM3000 Ports

Table 1 on page 4 provides required port information on the NSM3000.

Table 1: Required Ports on NSM3000

Depends on

ConfigurationInternetLANDescriptionPortDirection

NoNoYesSSH command-line management22In

NoNoYesWeb interface for administrator

443

YesYesLANWeb interface for listening for NSM

API messages.

8443

NoYesYesConnections from managed

devices to NSM3000

7800

NoNoYesConnections from the NSM GUI

Client to NSM

7801

YesNoYesHeartbeat between peers in an HA

cluster

7802

YesYesYesConnections from managed IDP

devices to NSM

7803

YesYesYesConnections from devices running

Junos, Secure Access devices, or

Infranet Controller devices

7804

NSM3000 Quick Start

Table 1: Required Ports on NSM3000 (continued)

Depends on

ConfigurationInternetLANDescriptionPortDirection

NoYesYesSSH connection to new managed

device

22Out

YesNoYesTelnet connection to new

managed device

NoNoYesDNS lookups53

YesYesNoSystem Security Updates from

Juniper Networks

YesNoYesShared Disk portmap lookup111

YesYesYesNetwork Time Protocol (NTP) time

synchronization

123

YesNoYesShared Disk NFS connection2049

For more information on ports, refer to the Network and Security Manager Installation

Guide.

Installing the NSM3000 Hardware

Follow these steps to unpack the NSM3000 appliance and connect it to your network.

To install NSM3000:

1. Place the shipping container on a flat surface and remove the hardware components

with care.

2. Remove the NSM3000 device from the shipping container and place it on a flat

surface.

3. Mount NSM3000 in your server rack using the attached mounting brackets.

4. Plug the power cord into the AC receptacle on the rear panel.

Figure 1: Rear Panel of NSM3000

g040042

Power

supply

AC Power

supply

receptacle

AC Power Blank power

supply tray

switch

Fan 0 Fan 1

Hardware Installation

If your NSM3000 contains two power supplies, plug a power cord into each AC

receptacle.

5. Plug the other end of the power cord into a wall socket.

If your NSM3000 contains two power supplies, plug each power cord into a separate

power circuit to ensure that the NSM3000 continues to receive power if one of the

power circuits fails.

6. Plug the Ethernet cable into the port marked ETH0 on the front panel.

Figure 2: Front Panel of NSM3000

CONSOLE ETH3 ETH2 ETH1 ETH0

g040041

Power

LED

Hardware

LED

Hard disk LED

Console

port

Ethernet

ports

USB

port

Hard disk

Activity LED

Hard disk

Failure LED

7. Plug the null modem serial cable into the console port.

This cable was shipped with your NSM3000. If you do not have this cable, use any

other null modem serial cable.

8. Push the power button in the upper left corner of the front panel.

The green LED below the power button turns on. The NSM3000 hard disk LED turns

on whenever the appliance reads data from or writes data to an NSM3000 hard disk.

The internal port uses two LEDs to indicate the LAN connection status, which is described

in Table 2 on page 6.

Table 2 on page 6 provides LED information for the Ethernet ports.

Table 2: Ethernet Port LEDs

LED2LED 1LAN Status

OffOff10 Mbps connection

OffGreen100 Mbps connection

OffOrange1000 Mbps connection

BlinkingOrange, Green, or OffData is being transferred

OffOffNo connection

NSM3000 Quick Start

Initial Setup Configuration

When you first turn on an unconfigured NSM3000 appliance, you need to enter basic

network and machine information through the serial console to make your appliance

accessible to the network. After entering these settings, you can continue configuring

the appliance using the CLI or the Web interface. You are not prompted for the initial

setup information again.

This section describes the required serial console setup and the tasks you need to perform

when connecting to your NSM3000 for the first time:

•Boot NSM3000 on page 7

•Set Up Your Appliance on page 7

Boot NSM3000

To configure NSM3000 for the first time, you must attach your NSM3000 appliance to

a console terminal running an emulation utility such as HyperTerminal.

1. Configure a console terminal or terminal emulation utility to use the following serial

connection parameters:

•9600 bits per second

•8-bit no parity (8N1)

•1 stop bit

•No flow control

2. Connect the terminal or laptop to the null modem serial cable plugged into the

NSM3000 console port.

3. Turn on the NSM3000 appliance.

When NSM3000 is powered on, the serial console displays diagnostic information

before proceeding to the boot countdown. When complete, the serial console displays

the login prompt terminal emulator.

NSMXpress.juniper.net login:

4. Enter admin as your default login name.

5. Enter abc123 as your default password.

6. Change your default password when prompted. Enter the default password first,

followed by your new password. All passwords are case-sensitive.

Set Up Your Appliance

This section provides the minimum information necessary to make your appliance active

on the network.

To set up your appliance either as a regional server or a central manager, follow these

steps:

Initial Setup Configuration

1. Enter the IP address for interface eth0 and press Enter.

2. Enter the subnet mask for interface eth0 and press Enter.

3. Enter the default route or default gateway address for interface eth0 and press Enter.

Applying changes...

Re-loading database

Done!

Your NSMXpress is now active on the network.

To configure your system via a web browser, connect to:

https://10.150.43.205/administration

To configure your system via command line, type:

nsm_setup

For operation of NSM server, switch to user “nsm”.

Please consult NSM product documentation for details.

[admin@NSMXpress ~]$

To configure the NSM software using the CLI, see the NSMXpress and NSM3000 User

Guide. To configure the NSM software using the Web interface, go to “Web Interface

Configuration” on page 8.

Web Interface Configuration

To configure NSM on your system from a Web interface, use the following steps.

1. Copy the URL (starting with https://) from the terminal emulator after installing the

NSM3000:

Your NSMXpress is now active on the network.

To configure your system via a web browser, connect to:

https//10.150.43.205/administration

2. Open a Web browser and paste the URL into the address text box.

3. Press Enter to open the NSM appliance login page.

4. Enter the admin user name and password and then click Login.

5. See “Configuring the NSM Software” on page 8 for details about how to install and

configure NSM on your NSM3000 appliance from the Web interface.

Configuring the NSM Software

After you log in as an “admin” user, an initial setup script walks you through additional

configuration system settings before finalizing the NSM installation. This chapter describes

that setup process.

NSM3000 Quick Start

Your NSM3000 appliance comes preconfigured as a regional server or a central manager.

Most installation and configuration steps in this section are identical for both types of

server. All exceptions are noted.

After logging into the NSM3000 Web interface, NSM3000 provides you with the following

installation options:

•Configuring Basic Settings on page 9

•Configuring High Availability on page 11

•Advanced Options on page 14

•Installing NSM Software on page 17

Configuring Basic Settings

To install the regional server or central manager software using the minimum

requirements:

1. Install your NSM3000 hardware as described in “Hardware Installation” on page 4.

2. Boot and setup your NSM3000 appliance as described in “Initial Setup Configuration”

on page 7.

3. Enter the https://<ip>/administration URL for your appliance in a Web browser. See

“Web Interface Configuration” on page 8 for details.

4. Log into the Web interface. The System Info page opens.

5. Click the link Install NSM Regional Server (see Figure 3 on page 10) to go to the Install

Regional Server window or click the Install NSM Central Manager link to view the Install

NSM Central Manager window (see Figure 4 on page 10), as the case may be.

NOTE: The “admin” user default username is admin and the password is

the one you created in Step 6 of “Boot NSM3000” on page 7.

Configuring the NSM Software

Figure 3: Regional Server Configuration Main Menu

Figure 4: Central Manager Configuration Main Menu

NSM3000 Quick Start

Otros manuales para NETWORK AND SECURITY MANAGER NSM3000 - REV...

Tabla de contenidos

Otros manuales de Software de Juniper

Juniper

Juniper JUNOSE SOFTWARE FOR E SERIES 11.3.X - PHYSICAL LAYER CONFIGURATION GUIDE... Manual de usuario

Juniper

Juniper BGP - CONFIGURATION GUIDE V 11.1.X Manual de usuario

Juniper

Juniper JUNOSE 11.2.X BGP AND MPLS Manual de usuario

Juniper

Juniper JUNOSE FOR E SERIES BROADBAND SERVICES ROUTERS - S... Manual de instrucciones

Juniper

Juniper TEPM AGENT - RELEASE NOTES 17-12-10 Manual de instrucciones

Juniper

Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV... Manual de usuario

Juniper

Juniper JUNOS SPACE Guía de instalación

Juniper

Juniper STRM 2008-2 - TECHNICAL NOTE CHANGING NETWORK SETTING... Manual de instalación y operación

Juniper

Juniper JUNOSE 11.1.X - COMMAND REFERENCE A TO M... Manual de instalación

Juniper

Juniper NETWORK AND SECURITY MANAGER - S REV 3 Manual de instrucciones

Juniper

Juniper SYSTEM BASICS - CONFIGURATION GUIDE V 11.1.X Manual de usuario

Juniper

Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE... Manual de instrucciones

Juniper

Juniper RESIDENT ENGINEER Manual de usuario

Juniper

Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 R2 - LOG MANAGEMENT ADMINISTRATION GUIDE REV... Manual de usuario

Juniper

Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV... Manual de usuario

Juniper

Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV... Manual de usuario

Juniper

Juniper JUNOSE SOFTWARE FOR E SERIES 11.3.X - COMMAND REFERENCE N TO Z... Manual de instalación

Juniper

Juniper SECURITY THREAT RESPONSE MANAGER - LOG MANAGEMENT INSTALLATION REV... Manual de usuario

Juniper

Juniper JUNOSE SOFTWARE FOR E SERIES 11.3.X - BGP AND MPLS CONFIGURATION GUIDE... Manual de usuario

Juniper

Juniper NETWORK AND SECURITY MANAGER - NSM CONFIGURATION GUIDE FOR EX SERIES DEVICES REV... Manual de usuario

Juniper

Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING INTRUSION DETECTION PREVENTION DEVICES GUIDE REV... Manual de usuario

Juniper

Juniper JUNOS OS 10.4 - FOR EX REV 1 Manual de usuario

Juniper

Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - ADAPTIVE LOG EXPORTER... Manual de usuario

Juniper

Juniper JUNOS 10.1 - S REV 4 Manual de instrucciones

Manuales populares de Software de otras marcas

COMPRO

COMPRO COMPROFM Manual de usuario

Muratec

Muratec OFFICEBRIDGE ONLINE Manual de usuario

Oracle

Oracle Contact Center Anywhere 8.1 Manual de usuario

Adobe

Adobe 65007312 - Photoshop Lightroom Manual

Avaya

Avaya NULL One-X for RIM Blackberry Manual de usuario

HP ProLiant BL420c Manual de usuario

PS Audio

PS Audio PowerPlay Manual del propietario

Brady

Brady LOCKOUT PRO 3.0 Manual de servicio

Avaya

Avaya Interaction Center Manual de usuario

Texas Instruments

Texas Instruments TI-83 Plus Silver Edition Manual

Novell

Novell GROUPWISE 8 - INTERNET AGENT Manual de usuario

Oracle

Oracle Application 9i Manual de usuario

Acer

Acer RDM Manual de usuario

Canon

Canon Vixia HF21 Manual de usuario

Canon

Canon ZR950 Manual de usuario

Samsung

Samsung Auto Backup Manual de usuario

Polycom

Polycom Vortex EF2201 Instrucciones de instalación y funcionamiento

Brocade Communications Systems

Brocade Communications Systems Brocade 8/12c Manual de usuario

Juniper NETWORK AND SECURITY MANAGER NSM3000 - REV... Manual de usuario

Manuales populares de Software de otras marcas