Juniper T640 Manual de usuario

T640 Core Router Quick Start

January 2015

Part Number: 530-062015

Revision 01

This document describes how to install the Juniper Networks®T640 Core Router.

Contents T640QuickStartDescription..........................................3

Step1:PreparingtheSite..............................................4

Rack-MountingRequirements......................................4

Tools Required to Unpack and Prepare the T640 Router for Installation . . . . . 5

Step 2: Installing the Mounting Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Installing the Mounting Hardware for a Four-Post Rack or Cabinet . . . . . . . . . 7

InstallingCageNuts,IfNeeded..................................8

Installing the Large Mounting Shelf and Spacer Bars . . . . . . . . . . . . . . . . 8

Installing the Small Mounting Shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Removing the Center-Mounting Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Installing the Mounting Hardware in an Open-Frame Rack . . . . . . . . . . . . . . . 9

InstallingCageNutsifNeeded..................................11

Installing the Large Mounting Shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Removing the Spacer Bars and Center-Mounting Brackets . . . . . . . . . . . 11

Step3:InstallingtheRouter...........................................12

InstallingtheRouterUsingaLift....................................12

Installing the Router Without a Mechanical Lift . . . . . . . . . . . . . . . . . . . . . . . . 13

RemovingComponents.......................................13

LiftingtheRouterintotheRack.................................16

ReinstallingComponents......................................18

Step 4: Connecting the Grounding Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Step 5: Connecting External Devices and PIC Cables . . . . . . . . . . . . . . . . . . . . . . . 20

ConnectingaManagementDevice.................................20

Connecting to a Network for Out-of-Band Management . . . . . . . . . . . . . . . . 21

ConnectingthePICCables........................................21

Step6:ConnectingPower............................................22

Connecting Power to a T640 Router with Two-Input 160-A DC Power

Supplies ...................................................22

Connecting Power to a T640 Router with Three-Input 240-A DC Power

Supplies ...................................................24

Setting the Input Mode Switch on a Three-Input 240-A DC Power

Supply.................................................24

Replacing the Cable Restraint on a Three-Input 240-A DC Power Supply

(Optional)..............................................25

ConnectingtheDCPowerCables...............................27

Connecting Power to a T640 Router with Four-Input 160-A DC Power

Supplies ...................................................28

Connecting Power to a T640 Router with Six-Input DC Power Supplies . . . . 30

Connecting Power to a T640 Router with Three-Phase Delta AC Power

Supplies ...................................................34

Connecting Power to a T640 Router with Three-Phase Wye AC Power

Supplies ...................................................36

Step7:PoweringOntheT640Router..................................39

Powering On the DC-Powered Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

PoweringOntheAC-PoweredRouter................................41

Step 8: Performing the Initial Software Configuration . . . . . . . . . . . . . . . . . . . . . . 42

EnteringConfigurationMode......................................42

Configuring User Accounts and Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

ConfiguringSystemAttributes.....................................43

CommittingtheConfiguration.....................................44

SafetyWarnings....................................................47

ComplianceStatementsforNEBS.....................................49

Compliance Statements for EMC Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Canada .......................................................49

EuropeanCommunity............................................49

Israel .........................................................50

Japan.........................................................50

United States ..................................................50

Junos OS Documentation and Release Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

RequestingTechnicalSupport.........................................51

Self-Help Online Tools and Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

OpeningaCasewithJTAC........................................52

RevisionHistory ....................................................52

T640 Core Router Quick Start

T640 Quick Start Description

This Quick Start contains information you need to install and configure the router quickly.

For complete installation instructions, see the T640 Core Router Hardware Guide at

http://www.juniper.net/techpubs/hardware/.

WARNING: This Quick Start contains a summary of safety warnings in “Safety

Warnings” on page 47. For a complete list of warnings for this router, including

translations, see the T640 Core Router Hardware Guide at

http://www.juniper.net/techpubs/hardware/.

The router is shipped in a wooden crate. A wooden pallet forms the base of the crate.

The router chassis is bolted to this pallet. The shipping crate also contains an accessory

box and a Quick Start (this document).

T640 Quick Start Description

Step 1: Preparing the Site

Before installing the router, make sure that the site meets all the power, environmental,

and clearance requirements. See the site preparation guidelines in the T640 Core Router

Hardware Guide.

•Rack-Mounting Requirements on page 4

•Tools Required to Unpack and Prepare the T640 Router for Installation on page 5

Rack-Mounting Requirements

•You can install the router in many types of racks, including a four-post rack or cabinet

or an open-frame rack.

•The rack rails must be spaced widely enough to accommodate the router chassis's

external dimensions: 37.45 in. (95.6 cm) high, 31 in. (78.7 cm) deep, and 17.43 in. (44.3

cm) wide. The mounting brackets extend the width to fit into standard 19-in. (48.3

cm) racks.

•The rack must be strong enough to support the weight of the fully configured router,

up to about 565 lb (256.3 kg). If you mount two routers in one rack, it must be capable

of supporting a combined weight of over 1100 lb (499 kg).

•For service personnel to remove and install hardware components, there must be

adequate space at the front and back of the router. Allow at least 24 in. (61.0 cm) both

in front of and behind the router.

•The rack or cabinet must have an adequate supply of cooling air.

•In a closed cabinet, there must be a minimum of 6 in. (15.2 cm) of unobstructed airflow

behind the router, or airflow baffles must be installed to prevent recirculation of hot

air and overheating.

•If the router is the only unit in the rack, mount it at the bottom.

•When mounting the router in a partially filled rack, load the rack from the bottom to

the top, with the heaviest component at the bottom of the rack.

T640 Core Router Quick Start

Figure 1: Rack Clearances and Router Dimensions

Tools Required to Unpack and Prepare the T640 Router for Installation

•A mechanical lift—recommended

•1/2-in. or 13-mm open-end or socket wrench to remove bracket bolts from the shipping

pallet

•Phillips screwdrivers, numbers 1 and 2

•DC-powered routers: 7/16-in. (11 mm) hexagonal-head external drive nut driver, with

a torque range between 23 lb-in. (2.6 Nm) and 25 lb-in. (2.8 Nm), for tightening nuts

to terminal studs on each power supply on a DC-powered router

•AC-powered router:

•Phillips (+) screwdriver, number 2 to access the metal AC wiring compartment

Tools Required to Unpack and Prepare the T640 Router for Installation

•1/4-in. slotted screwdriver to attach the ground wire and input terminal wires of the

AC power cord.

•Wire cutters

•Cage nuts, if needed for your rack or cabinet

•Electrostatic discharge wrist strap

•Antistatic mat

•Blank panels to cover any slots not occupied by a component

T640 Core Router Quick Start

Step 2: Installing the Mounting Hardware

To install the mounting hardware:

•Installing the Mounting Hardware for a Four-Post Rack or Cabinet on page 7

•Installing the Mounting Hardware in an Open-Frame Rack on page 9

Installing the Mounting Hardware for a Four-Post Rack or Cabinet

Figure 2: Mounting Hardware for a Four-Post Rack or Cabinet

An x in Table 1 on page 7 indicates a mounting hole location.

Table 1: Four-Post Rack and Cabinet Mounting Hole Locations

Small

Shelf

Spacer

BarsLarge ShelfDistance Above “U” DivisionHole

–x–19.86 U34.75 in. (88.3 cm)60

–x–16.86 U24.26 in. (61.6 cm)51

–x–13.86 U24.26 in. (61.6 cm)42

Step 2: Installing the Mounting Hardware

Table 1: Four-Post Rack and Cabinet Mounting Hole Locations (continued)

Small

Shelf

Spacer

BarsLarge ShelfDistance Above “U” DivisionHole

–x–10.86 U19.01 in. (48.3 cm)33

–x–7.86 U13.76 in. (34.9 cm)24

xx–4.86 U8.51 in. (21.6 cm)15

x––3.86 U6.76 in. (17.1 cm)12

x––4.86 U5.01 in. (12.7 cm)9

xx–1.86 U3.26 in. (8.3 cm)6

x––0.86 U1.51 in. (3.8 cm)3

––x0.5 U0.88 in. (2.2 cm)2

To install the mounting hardware for a four-post rack or cabinet:

•Installing Cage Nuts, If Needed on page 8

•Installing the Large Mounting Shelf and Spacer Bars on page 8

•Installing the Small Mounting Shelf on page 9

•Removing the Center-Mounting Brackets on page 9

Installing Cage Nuts, If Needed

For racks without threaded holes, you must install cage nuts in the locations specified in

Table 1 on page 7:

•On each front rack rail, install cage nuts for the large shelf and spacer bars.

•On each rear rack rail, install cage nuts for the small shelf.

Installing the Large Mounting Shelf and Spacer Bars

1. On the front side of each front rail, partially insert a mounting screw into the lowest

hole specified in Table 1 on page 7 for the large shelf.

2. Install the large shelf on the front side of the front rack rails. Rest the bottom slot in

each flange on one of the mounting screws.

3. Tighten all the screws completely.

4. Place one spacer bar over a flange of the large shelf.

5. Partially insert a mounting screw into each of the nonthreaded holes in the recesses

of the spacer bar.

T640 Core Router Quick Start

6. Repeat Step 4 and Step 5 for the other spacer bar.

7. Tighten all the screws completely.

Installing the Small Mounting Shelf

The small shelf installs on the back of the rear rails, extending toward the center of the

rack. See Table 1 on page 7.

1. Partially insert a mounting screw into the lowest hole specified in Table 1 on page 7.

2. Install the small shelf on the back of the rear rack rails. Rest the bottom slot on each

flange on one of the mounting screws.

3. Partially insert screws into the open holes in the ears of the small shelf.

4. Tighten all the screws completely.

Removing the Center-Mounting Brackets

The router is shipped with a spacer bar attached to the back of each front-mounting

flange, and two center-mounting brackets attached to the chassis. Remove the center

mounting brackets from the chassis by loosening the screws at the top and bottom of

each bracket.

Installing the Mounting Hardware in an Open-Frame Rack

To install the mounting hardware for an open frame rack:

•Front-mount: Attach the large mounting shelf on the back of the rails. Remove the

center-mounting brackets from the chassis.

•Center mount: Attach the large mounting shelf on the back of the rails. You do not

have to remove the center-mounting brackets from the chassis.

The small mounting shelf is not needed for open-frame racks.Table 2 on page 10 specifies

the holes in which you insert mounting screws, and cage nuts if needed.

Installing the Small Mounting Shelf

Figure 3: Mounting Hardware for an Open-Frame Rack

An x in Table 2 on page 10 indicates a mounting hole location.

Table 2: Open-Frame Rack Mounting Hole Locations

Large ShelfDistance Above U DivisionHole

x19.5 U34.13 in. (86.7 cm)59

x17.5 U30.63 in. (77.8 cm)53

x16.5U28.88 in. (73.3 cm)50

x14.5 U25.38 in. (64.5 cm)44

x13.5 U23.63 in. (60.0 cm)41

x11.5 U20.13 in. (51.1 cm)35

x10.5 U18.38 in. (46.7 cm)32

T640 Core Router Quick Start

Otros manuales para T640

Tabla de contenidos

Otros manuales de Enrutador de red de Juniper

Juniper

Juniper T4000 - Manual de usuario

Juniper

Juniper ACX5448-D Instrucciones de instalación

Juniper

Juniper MX480 Manual de usuario

Juniper

Juniper T640 Instrucciones de instalación

Juniper

Juniper ACX4000 Manual de usuario

Juniper

Juniper T1600 Manual de usuario

Juniper

Juniper M40e Instrucciones de instalación

Juniper

Juniper MX240 Manual de usuario

Juniper

Juniper V10000 Manual de usuario

Juniper

Juniper PTX1000 Instrucciones de instalación

Juniper

Juniper ERX - RELEASE 11.1.X HARDWARE GUIDE... Instrucciones de instalación

Juniper

Juniper JUNOS OS 10.4 Manual de usuario

Juniper

Juniper TX MATRIX Instrucciones de instalación

Juniper

Juniper M7i Instrucciones de instalación

Juniper

Juniper MX10008 Instrucciones de instalación

Juniper

Juniper MX10016 Manual de usuario

Juniper

Juniper PTX Series Manual de usuario

Juniper

Juniper ACX500 Instrucciones de instalación

Juniper

Juniper MX240 Instrucciones de instalación

Juniper

Juniper M7i Manual de usuario

Juniper

Juniper T4000 - Instrucciones de instalación

Juniper

Juniper ACX1100 Manual de usuario

Juniper

Juniper ACX5448 Manual de usuario

Juniper

Juniper MX104 Instrucciones de instalación

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad