Juniper JCS 1200 Manual de usuario

Replacing a JCS 1200 Management Module or Module Filler

Topics include:

■Removing a JCS 1200 Management Module or Module Filler on page 1

■Installing a JCS 1200 Management Module or Module Filler on page 2

Removing a JCS 1200 Management Module or Module Filler

Figure 1 on page 1 shows how to remove and install a management module.

Figure 1: Removing and Installing a JCS 1200 Management Module

When you remove a management module, keep in mind the following:

■These instructions assume that the JCS 1200 platform is connected to power.

■If you are replacing the only management module in the JCS 1200 platform and

the management module is functioning, save the configuration file before you

proceed. For information about saving and restoring a configuration file, see the

JUNOS Protected System Domain Configuration Guide.

■If you have just installed a second management module in the JCS 1200 platform,

do not remove the first (primary) management module for up to 45 minutes;

the second (redundant) management module needs the time to receive initial

status information and firmware from the management module.

To remove a management module or module filler (see Figure 1 on page 1):

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and

connect the strap to one of the ESD points on the chassis.

2. Pull the management module release handle to the open position. The module

moves out of the bay approximately 0.25 in. (0.6 cm).

3. Slide the management module out of the bay.

Replacing a JCS 1200 Management Module or Module Filler ■1

Installing a JCS 1200 Management Module or Module Filler

Figure 2 on page 2 shows how to remove and install a management module.

Figure 2: Removing and Installing a JCS 1200 Management Module

To install a management module or module filler (see Figure 2 on page 2):

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and

connect the strap to one of the ESD points on the chassis.

2. Remove the management module filler, if one is installed.

3. Remove the management module interposer filler tray, if one is installed.

4. Install the management module interposer, if it is not already installed.

5. Make sure that the release handle on the management module is in the open

position.

6. Slide the management module into the management module bay until it stops.

7. Push the management module release handle to the closed position.

8. Connect any cables to the management module.

9. If the JCS 1200 platform is connected to power, make sure that the OK LED on

the management module is lit. If the management module is redundant, wait at

least 45 minutes for the modules to copy the configuration data before you make

any changes to the management module configuration.

Related Topics ■Preventing Electrostatic Discharge Damage to the JCS 1200 Platform

■JCS 1200 Management Module Description

■Replacing a JCS 1200 Management Module Filler Tray

■Locating the JCS 1200 Management Module Serial Number

2■Installing a JCS 1200 Management Module or Module Filler

Otros manuales para JCS 1200

6

Tabla de contenidos

Otros manuales de Enrutador de red de Juniper

Juniper

Juniper M40e Instrucciones de instalación

Juniper

Juniper ACX1000 Manual de usuario

Juniper

Juniper J2300 Manual de usuario

Juniper

Juniper MX2008 Instrucciones de instalación

Juniper

Juniper EX4500 Series Instrucciones de instalación

Juniper

Juniper NFX150-S1 Manual de usuario

Juniper

Juniper EX9200 Series Hoja de especificaciones

Juniper

Juniper PTX10001-36MR Manual de usuario

Juniper

Juniper T320 Instrucciones de instalación

Juniper

Juniper T4000 - Manual de usuario

Juniper

Juniper E-Series Instrucciones de instalación

Juniper

Juniper JCS 1200 Manual de usuario

Juniper

Juniper ACX2000 Manual de usuario

Juniper

Juniper EX9200 Series Hoja de especificaciones

Juniper

Juniper J2320 Manual de usuario

Juniper

Juniper MX480 Manual de usuario

Juniper

Juniper MX240 Instrucciones de instalación

Juniper

Juniper MX240 Instrucciones de instalación

Juniper

Juniper J2300 Manual de usuario

Juniper

Juniper E120 Manual de usuario

Juniper

Juniper TX MATRIX PLUS Instrucciones de instalación

Juniper

Juniper M40 Instrucciones de instalación

Juniper

Juniper E320 Manual de usuario

Juniper

Juniper MX104 Instrucciones de instalación

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad