Juniper MX2010 Manual de usuario
MX2010 Universal Roung Plaorm
Published
2023-10-05
RELEASE
Table of Contents
MX2010 Quick Start Descripon
Step 1: Prepare the Site for Installaon
Rack-Mounng Requirements | 2
Moving Requirements and Guidelines Using a Router Transport Kit | 5
Tools Required to Unpack and Prepare the Router for Installaon | 8
Step 2: Install the Mounng Hardware
Install the Mounng Hardware | 9
Step 3: Install the Router
Unpack the Router | 12
Remove Components | 15
Install the Router Using a Pallet Jack with Aachment | 22
Install the Pallet Jack Aachment | 22
Use the Pallet Jack with Aachment to Install the Router | 23
Install the Router Using a Router Transport Kit | 29
Unpack the Router Transport Kit | 29
Install the Router Transport Kit onto the Router | 33
Secure the Router to the Transport Plaorm | 35
Use the Router Transport Kit to Install the Router in a Four-Post Rack | 38
Use the Router Transport Kit to Install the Router in an Open-Frame Rack | 48
Step 4: Connect the Grounding Cable
Step 5: Reinstall Components
Step 6: Connect External Devices and Line Card Cables
Connect to a Network for Out-of-Band Management | 58
ii
Connect a Management Console | 58
Connect the Line Card Cables | 58
Step 7: Connect Power Cables
Connect Power to a Three-Phase Delta AC Power Distribuon Module | 60
Connect Power to a Three-Phase Wye AC Power Distribuon Module | 64
Connect AC Power Supply Modules | 68
Connect Power to a DC Power Distribuon Module | 71
Connect DC Power Supply Modules | 74
Step 8: Perform Inial Soware Conguraon
Enter Conguraon Mode | 78
Congure User Accounts and Passwords | 78
Congure System Aributes | 79
Commit the Conguraon | 81
Safety Warnings
iii
MX2010 Quick Start Descripon
This Quick Start contains informaon to help you quickly install and congure the MX2010 Universal
Roung Plaorm. For complete installaon instrucons, see the MX2010 Universal Roung Plaorm
Hardware Guide at hps://www.juniper.net/documentaon/.
WARNING: This Quick Start contains a summary of safety warnings in "Safety
Warnings" on page 82. For a complete list of warnings for this router, including
translaons, see the MX2010 Universal Roung Plaorm Hardware Guide at hps://
www.juniper.net/documentaon/.
The MX2010 Universal Roung Plaorm is shipped in a wooden crate. A wooden pallet forms the base
of the crate. The MX2010 chassis is bolted to this pallet. The shipping crate also contains a large rack
mount tray, electromagnec interference (EMI) cover, a cardboard accessory box, and a Quick Start (this
document).
NOTE: The shipping container and router (fully populated) weighs approximately 1343 lb (609.17
kg), depending on your conguraon.
The MX2010 Universal Roung Plaorm with standard cable managers and EMI cover measures
59.50 in. (151.13 cm) high, 19 in. (48.26 cm) wide, and 36.20 in. (91.95) deep (from the front-mounng
anges to the rear of the chassis). An extended cable manager extends the depth to 40.15 in. (102 cm).
One router can be installed in a 34-U or taller open-frame or four-post rack if the rack can support the
combined weight, which can be greater than 985 lb (445.79 kg).
NOTE: The dimensions also include the cable managers and EMI cover.
NOTE: If you are installing the MX2010 router into a network cabinet, make sure that no
hardware, device, rack, or cabinet components obstruct the 34-U rack space from access during
installaon.
The MX2010 router has 10 dedicated line-card slots, which means a maximum of 10 Modular Port
Concentrators (MPCs) including adapter cards (ADCs), and Modular Interface Cards (MICs), a host
subsystem consisng of two Control Board with Roung Engines (CB-REs), and eight Switch Fabric
Boards (SFBs).
1
Adapter cards provide housing to MPCs. The MPCs aach to the adapter cards, which in turn connect to
the backplane.
Up to two MICs can be installed in each MPC. Fully populated, the MX2010 router supports up to 20
MICs.
For a list of the supported MPCs and MICs, see the
MX Series Interface Module Reference
.
Step 1: Prepare the Site for Installaon
IN THIS SECTION
Rack-Mounng Requirements | 2
Moving Requirements and Guidelines Using a Router Transport Kit | 5
Tools Required to Unpack and Prepare the Router for Installaon | 8
Rack-Mounng Requirements
• You can install the router in an open-frame rack, a four-post rack, or a cabinet.
NOTE: The shipping and installaon site must be an ESD-approved area.
• The rack rails must be spaced widely enough to accommodate the chassis’s external dimensions:
59.50 in. (151.13 cm) high, 36.20 in. (91.95 cm) deep, and 19 in. (48.26 cm) wide (from the front-
mounng anges to the rear of the chassis). An extended cable manager extends the depth to 40.15
in. (102 cm). See Figure 1 on page 4 and Figure 2 on page 5).
In an open-frame rack, center-mounng is required to provide an even distribuon of weight for
greater stability. For center-mounng, use the mounng brackets aached to the center of the
chassis for rack mounng.
• The rack must be strong enough to support the weight of the fully congured router, up to 985 lb
(446.79 kg).
2
• For the cooling system to funcon properly, the airow around the chassis must be unrestricted.
Allow at least 36 in. (91.44 cm) of clearance between front-to-rear-cooled routers. Allow 2.8 in.
(7 cm) between the side of the chassis and any non-heat-producing surface such as a wall.
NOTE: To help redirect exhaust air away from the chassis, there is an oponal adjustable air
bae that can be installed on the upper fan tray access.
• For service personnel to remove and install hardware components, there must be adequate space at
the front and back of the router. Allow at least 36 in. (91.44 cm) in front of the router and
36 in. (91.44 cm) behind the router.
• The rack or cabinet must have an adequate supply of cooling air.
• Ensure that the cabinet allows the hot exhaust air of the chassis to exit from the cabinet without
recirculang into the router.
• The router must have the shipping covers installed to help move the router into the rack or cabinet.
• The router must be installed into a rack or cabinet that is secured to the building structure.
• The cabinet must be clear of any hardware, device, rack, or cabinet component that obstructs the 34-
U rack space from being access during installaon.
3
Figure 1: MX2010 Rack Clearance and Router Dimensions for Four-Post Rack
4
NOTE: The router transport kit handles can be removed to accommodate aisle width.
Figure 3: Turning Diameter of Router Transport Kit
The weight of the router transport kit is 138.5 lb (63 kg). The maximum recommended height the router
should be lied from the oor using the router transport kit is 1.5 in. (3.8 cm).
Viewed from the side, the router with the router transport kit installed measures 59.50 in. (151.13 cm)
high and 36.20 in. (91.95 cm) wide, with the transport kit measuring 23.40 in. (59.4 cm) high (see Figure
4 on page 7).
6
Otros manuales para MX2010
1
Tabla de contenidos
Otros manuales de Enrutador de red de Juniper
Juniper
Juniper E SERIES BROADBAND SERVICES ROUTERS 11.3.X - ERX HARDWARE GUIDE REV... Instrucciones de instalación
Juniper
Juniper TX MATRIX PLUS Instrucciones de instalación
Juniper
Juniper ACX2000 Manual de usuario
Juniper
Juniper QFX5100 Instrucciones de instalación
Juniper
Juniper M40e Instrucciones de instalación
Juniper
Juniper MX2010 Instrucciones de instalación
Juniper
Juniper PTX1000 Instrucciones de instalación
Juniper
Juniper ACX5096 Manual de usuario
Juniper
Juniper ERX-310 Manual de usuario
Juniper
Juniper MX960 Manual de usuario
Juniper
Juniper EX2500 Manual de usuario
Juniper
Juniper QFX10002 Manual de usuario
Juniper
Juniper ACX2200 Manual de usuario
Juniper
Juniper J-Series Manual de usuario
Juniper
Juniper T1600 Manual de usuario
Juniper
Juniper CTP2000 Series Manual del operador
Juniper
Juniper EX9200 Series Hoja de especificaciones
Juniper
Juniper PTX10003-160C Manual de usuario
Juniper
Juniper ERX-1410 Manual de usuario
Juniper
Juniper ACX2000 Manual de usuario
Manuales populares de Enrutador de red de otras marcas
NETGEAR
NETGEAR FS526T - Switch Manual de usuario
Korenix
Korenix JetNet 5710G Series Manual de usuario
Automated Logic
Automated Logic ZN551 Manual del propietario
Cisco
Cisco ASR 1000 Series Manual del operador
EnGenius
EnGenius ESR-9710 Manual de usuario
Cisco
Cisco 805 Series Instrucciones de funcionamiento y seguridad