Juniper MX150 Manual de usuario
Quick Start Guide
MX150
IN THIS GUIDE
Step 1: Begin | 1
Step 2: Up and Running | 3
Step 3: Keep Going | 5
Step 1: Begin
IN THIS SECTION
Mount the MX150 | 2
Connect Power to the Switch | 3
To mount and connect power to the Juniper Networks®MX150, and perform initial configuration, you need:
•Electrostatic discharge (ESD) grounding strap (not provided)
•One pair of front-mounting bracket (provided)
•Eight screws to secure the mounting bracket (provided)
•Four screws to secure the chassis and mounting bracket to the rack (not provided)
•Screwdriver appropriate for your rack mounting screws (not provided)
•An AC power cord with plugs appropriate for your geographical location (provided)
•RJ-45 cable and RJ-45 to DB-9 serial port adapter (provided)
•Management host, such as a PC or laptop, with a serial port (not provided)
•(Optional) A grounding cable (minimum 14 AWG (2 mm²), minimum 90°C wire), a grounding lug (Panduit LCC10-14BWL
or equivalent), a pair of 10-32x.25-in. screws, and a pair of flat washers (not provided). For information about installing
the grounding cable, see the MX150 documentation at https://www.juniper.net/documentation/product/en_US/mx150.
Register product serial numbers on the Juniper Networks website and update the installation base data if there is any
addition or change to the installation base or if the installation base is moved. Juniper Networks will not be held accountable
for not meeting the hardware replacement service-level agreement for products that do not have registered serial numbers
or accurate installation base data.
Register your product(s) at https://tools.juniper.net/svcreg/SRegSerialNum.jsp.
Update your install base at https://www.juniper.net/customers/csc/management/updateinstallbase.jsp.
Mount the MX150
You can mount the MX150 device on two posts of a 19-in. rack by using the mounting brackets provided with the device.
The device weighs approximately 9.4 lb (4.3 kg). Two persons are required for mounting the device.
1. Attach the ESD grounding strap to your bare wrist and to a site ESD point.
NOTE: If you are mounting multiple units in the rack, mount the heaviest unit at the bottom and mount the
others from bottom to top in order of decreasing weight.
2. Place the rack in its permanent location, allowing adequate clearance for airflow and maintenance, and secure it to the
building structure.
3. Align the mounting brackets along the front or rear of the side panels of the chassis— depending on whether you will
front-mount or rear-mount the device—and attach the mounting brackets to the chassis by using the mounting screws.
Tighten the screws.
4. Have one person grasp both sides of the device, lift the device, and position it in the rack, aligning the mounting bracket
holes with the threaded holes in the rack rail. Align the bottom hole in each mounting bracket with a hole in each rack
rail, making sure that the chassis is level.
5. Have the second person use the mounting screws (and cage nuts and washers if your rack requires them) to screw the
mounting bracket to the rack.
2
g006760
Connect Power to the Switch
1. Attach the grounding cable to earth ground and then to the chassis grounding points.
NOTE: We recommend grounding for AC-powered systems. An AC-powered device gets additional grounding
when you connect the power supply in the device to a grounded AC power outlet by using the power cord.
The MX150 device uses a fixed, internal AC power supply.
2. Set the power switch to the off (O) position.
3. Insert the power cord plug into the power source outlet.
4. Insert the power cord coupler firmly into the inlet.
5. Set the power switch to the on (|) position.
6. Verify that the power LED is lit green and on steadily
Step 2: Up and Running
You must perform the initial configuration of the device to configure the static IP address on Junos so that the router is
accessible from the remote server using telnet or ssh services.
To configure the device:
1. Log in as the root user. There is no password.
3
login: root
2. Start the CLI:
root% cli
3. Enter configuration mode:
root> configure
4. Remove Zero Touch Provisioning (ZTP) which enables the device to automatically upgrade the Junos OS software and
auto-install configuration files from the network.
root# delete chassis auto-image-upgrade
5. Specify a password for the root administration user account:
[edit]
root# set system root-authentication plain-text-password
New password: password
Retype new password: password
6. (Optional) Configure the name of the device. If the name includes spaces, enclose the name in quotation marks (“ ”):
[edit]
root# set system host-name host-name
7. Delete DHCP configuration so that you can configure the IP address and prefix length for the device management
interface:
[edit]
root# delete interfaces fxp0 unit 0 family inet dhcp
8. Configure the IP address and prefix length of the management interface:
[edit]
root# set interfaces fxp0 unit 0 family inet address address/prefix-length
9. Configure the default gateway:
4
[edit]
root# set routing-options static route default next-hop address
10. Enable SSH service.
[edit]
root# set system services ssh
11. Enable Telnet service.
[edit]
root# set system services telnet
12. Commit the configuration to activate it on the device:
[edit]
root# commit
Step 3: Keep Going
IN THIS SECTION
Safety Warnings Summary | 5
Power Cable Warning (Japanese) | 6
Contacting Juniper Networks | 6
See the complete MX Series documentation at https://www.juniper.net/documentation/product/en_US/mx150.
Safety Warnings Summary
This is a summary of safety warnings. For a complete list of warnings, including translations, see the MX Series
documentation at https://www.juniper.net/documentation/product/en_US/mx150.
5
WARNING: Failure to observe these safety warnings can result in personal injury or death.
•Permit only trained and qualified personnel to install or replace switch components.
•Perform only the procedures described in this quick start and the MX150 documentation. Other services must be
performed only by authorized service personnel.
•Before installing the device, read the planning instructions in the MX150 documentation to make sure that the site
meets power, environmental, and clearance requirements for the device.
•Before connecting the device to a power source, read the installation instructions in the MX150 documentation.
•The MX150 device weighs approximately 9.4 lb (4.3 kg). Manually installing the device in a rack at a height above 60
in. (152.4 cm) requires two persons; one to lift the device and the second to install the mounting screws. To prevent
injury while lifting, keep your back straight and lift with your legs, not your back.
•If the rack has stabilizing devices, install them in the rack before mounting or servicing the device in the rack.
•Before installing or after removing an electrical component, always place it component-side up on an antistatic mat
placed on a flat, stable surface or in an antistatic bag.
•Do not work on the device or connect or disconnect cables during electrical storms.
•Before working on equipment that is connected to power lines, remove jewelry, including rings, necklaces, and watches.
Metal objects heat up when connected to power and ground and can cause serious burns or become welded to the
terminals.
Power Cable Warning (Japanese)
The attached power cable is only for this product. Do not use this cable for another product.
g040300
Contacting Juniper Networks
For technical support, see:
http://www.juniper.net/support/requesting-support.html
6
Juniper Networks, the Juniper Networks logo, Juniper, and Junos are registered trademarks of Juniper Networks, Inc. in the
United States and other countries. All other trademarks, service marks, registered marks, or registered service marks are the
property of their respective owners. Juniper Networks assumes no responsibility for any inaccuracies in this document. Juniper
Networks reserves the right to change, modify, transfer, or otherwise revise this publication without notice. Copyright © 2020
Juniper Networks, Inc. All rights reserved. Rev. 01, March 2020.
7
Otros manuales para MX150
1
Tabla de contenidos
Otros manuales de Enrutador de red de Juniper
Juniper
Juniper CTP2000 Series Manual del operador
Juniper
Juniper EX9214 Instrucciones de instalación
Juniper
Juniper NFX150-S1 Manual de usuario
Juniper
Juniper ACX1100 Manual de usuario
Juniper
Juniper M20 Guía del usuario
Juniper
Juniper QFX10002 Manual de usuario
Juniper
Juniper M40 Guía del usuario
Juniper
Juniper PTX10001-20C Manual de usuario
Juniper
Juniper ERX-1410 Manual de usuario
Juniper
Juniper SRX240 Series Instrucciones de instalación
Juniper
Juniper ACX5048 Manual de usuario
Juniper
Juniper M40e Instrucciones de instalación
Juniper
Juniper E-Series Instrucciones de instalación
Juniper
Juniper J2300 Manual de usuario
Juniper
Juniper EX9200 Series Hoja de especificaciones
Juniper
Juniper T1600 Manual de usuario
Juniper
Juniper E-Series Manual de usuario
Juniper
Juniper PTX10001 Manual de usuario
Juniper
Juniper T640 Instrucciones de instalación
Juniper
Juniper Juniper Networks Instrucciones de instalación
Manuales populares de Enrutador de red de otras marcas
NETGEAR
NETGEAR FS526T - Switch Manual de usuario
Korenix
Korenix JetNet 5710G Series Manual de usuario
Automated Logic
Automated Logic ZN551 Manual del propietario
Cisco
Cisco ASR 1000 Series Manual del operador
EnGenius
EnGenius ESR-9710 Manual de usuario
Cisco
Cisco 805 Series Instrucciones de funcionamiento y seguridad