Juniper NFX150-S1 Manual de usuario

NFX150-S1 Network Services Platform

Quick Start

NFX150 Network Services Platform Overview

The Juniper Networks NFX150 Network Services Platform is a secure, automated, software-driven customer premises equipment

(CPE) that delivers virtualized network and security services on demand. The NFX150 integrates routing, switching, and security

functions on a single platform. The NFX150 is suited for small to medium-sized enterprises and can be used as a secure router

or Universal CPE (uCPE).

For more information on NFX150 Hardware, see the NFX150 Hardware Guide available at:

https://www.juniper.net/documentation/en_US/release-independent/junos/information-products/pathway-pages/nfx-series/product/

Package Contents

The NFX150-S1 device is shipped with the following parts:

•One pair of front-mounting brackets

•Eight screws to secure the mounting brackets to the chassis

•An AC power cord with plugs appropriate for your geographical location

•RJ-45 cable and RJ-45 to DB-9 serial port adapter

Register product serial numbers on the Juniper Networks website and update the installation base data if there is any addition

or change to the installation base or if the installation base is moved. Juniper Networks will not be held accountable for not

meeting the hardware replacement service-level agreement for products that do not have registered serial numbers or accurate

installation base data.

Update your installation base at https://www.juniper.net/customers/csc/management/updateinstallbase.jsp.

NFX150-S1 Front Panel and Rear Panel

Figure 1: Front Panel Components of NFX150-S1

g100000

41 32

79 8

6—1— Expansion module slotsMini USB console Port

7—2— Two 1-Gigabit Ethernet/10-Gigabit Ethernet SFP+ WAN portsRJ-45 console port

8—3— USB 3.0 portOne 10/100/1000BASE-T RJ-45 management port

9—4— Reset buttonFour 10/100/1000BASE-T RJ-45 LAN ports

5—System status LEDs

Figure 2: Rear Panel Components of NFX150-S1

g100002

1 2

7 6

5—1— FansAC power cord inlet

6—2— CLEI codePower switch

7—3— Electrostatic discharge (ESD) pointGrounding point

4—Serial number

Mount an NFX150-S1 Device on Two Posts of a Rack

To mount an NFX150-S1 device on a rack, you require the parts that are shipped with the device along with the following additional

parts and equipment. These are not shipped with the device.

•Electrostatic discharge (ESD) grounding strap

•Four screws to secure the chassis and mounting bracket to the rack

•Phillips (+) screwdriver, number 2

•Management host, such as a PC or laptop, with a serial port

•Grounding cable (minimum 14 AWG (2 mm²), minimum 90°C wire), grounding lug (Panduit LCC10-14BWL or equivalent), a

pair of 10-32x.25-in. screws, and a pair of flat washers

NFX150-S1 Network Services Platform Quick Start

For information about installing the grounding cable, see the NFX150 Hardware Guide available at:

https://www.juniper.net/documentation/en_US/release-independent/junos/information-products/pathway-pages/nfx-series/product/

You can mount an NFX150-S1 device on two posts of a 19-in. rack by using the mounting brackets provided with the device. To

install NFX150-S1 on two posts of a 23-in. rack, you need additional mounting brackets.

NOTE: The device weighs approximately 13 lb (5.9 kg). Two persons are required for mounting the device.

NOTE: Ensure that the rack is in its permanent location, allowing adequate clearance for airflow and maintenance,

and secured to the building structure.

NOTE: If you are mounting multiple units in the rack, mount the heaviest unit at the bottom and mount the other

units from bottom to top in the order of decreasing weight.

CAUTION: Wrap and fasten one end of the ESD grounding strap around your wrist and connect the other end to a

site ESD point.

To mount the device on a rack:

1. Align the mounting brackets along the front or rear of the side panels of the chassis— depending on whether you will front-mount

or rear-mount the device—and attach the mounting brackets to the chassis by using the mounting bracket screws. Tighten

the screws.

2. Have one person grasp both sides of the device, lift the device, and position it in the rack, aligning the mounting bracket holes

with the threaded holes in the rack rail. Align the bottom hole in each mounting bracket with a hole in each rack rail, making

sure that the chassis is level.

Figure 3: Mounting the Device on Two Posts of a Rack

g100014

3. Have the second person use the rack-mounting screws (and cage nuts and washers if your rack requires them) to attach the

mounting brackets to the rack.

NFX150-S1 Network Services Platform Quick Start

Connect Power to the Device

CAUTION: Wrap and fasten one end of the ESD grounding strap around your wrist and connect the other end to a

site ESD point.

NOTE: Ensure that you ground AC-powered systems by attaching one end of the grounding cable to earth ground

and the other end to the chassis grounding points.

To connect the device to the power supply:

1. Set the power switch on the device to the off (O) position.

2. Insert the power cord plug into the power source outlet and power cord coupler into the chassis power inlet.

3. Set the power switch to the on (|) position.

4. Verify that the power LED is lit green and on steadily.

Power Cable Warning (Japanese)

WARNING: The attached power cable is only for this product. Do not use this cable for another product.

Factory-Default Settings

The NFX150 device is shipped with the following factory-default settings:

Table 1: Security Policies

Policy ActionDestination ZoneSource Zone

permittrusttrust

permituntrusttrust

Table 2: Interface Mapping

IP AddressDHCP StateSecurity ZoneVirtual InterfaceInterfacePort Label

192.168.2.1/24Servertrustge-0/0/0 to ge-0/0/3heth-0-0 to heth-0-30/0 to 0/3

ISP assignedClientuntrustge-1/0/1heth-0-40/4

ISP assignedClientuntrustge-1/0/2heth-0-50/5

NFX150-S1 Network Services Platform Quick Start

Table 2: Interface Mapping (continued)

IP AddressDHCP StateSecurity ZoneVirtual InterfaceInterfacePort Label

192.168.1.1/24N/AN/AN/Afxp0MGMT

Table 3: LTE Interfaces

IP AddressSecurity ZoneInterface

N/AN/Acl-1/1/0

ISP assigneduntrustdl0 (logical)

The NFX150 device is shipped with the following services enabled by default: DHCP, HTTPS, and TFTP.

To provide secure traffic, a basic set of screens are configured on the untrust zone.

Access the Device

1. Ensure that the NFX150 device is powered on.

2. Connect to the console port:

a. Plug one end of the Ethernet cable into the console port on your NFX150 device.

b. Connect the other end of the Ethernet cable to the RJ-45—to—DB-9 serial port adapter shipped with your device.

c. Connect the RJ-45—to—DB-9 serial port adapter to the serial port on the management device. Use the following values

to configure the serial port:

Baud rate—9600; Parity—N; Data bits—8; Stop bits—1; Flow control—None.

NOTE: Alternately, you can use the USB cable to connect to the mini-USB console port on the device. To use the

mini-USB console port, you must download the USB driver from the following page and install it on the management

device:

https://www.juniper.net/support/downloads/junos.html

3. Use any terminal emulation program, such as HyperTerminal, to connect to the device console. The CLI displays a login prompt.

4. Log in as root and enter the password juniper123. If the software completes booting before you connect to the console, you

might need to press the Enter key for the prompt to appear:

password: juniper123

5. Start the CLI:

root@:~ # cli

root@>

6. Enter configuration mode:

root@> configure

[edit]

NFX150-S1 Network Services Platform Quick Start

root@#

7. Change the password for the root administration user account:

[edit]

root@# set system root-authentication plain-text-password

New password: password

Retype new password: password

8. Enable SSH service for the root user:

[edit]

root@# set system services ssh root-login allow

9. (Optional) Enable WAN connection for devices connected on LAN:

[edit]

root@# set access address-assignment pool junosDHCPPool family inet dhcp-attributes name-server dns-server-ip

10. Commit the configuration:

[edit]

root@# commit

Establish the Connection

1. Connect the device to the Internet Service Provider (ISP) by using the following step:

NOTE: For information on interface mapping, see Table 2 and Table 3.

Connect one of the WAN ports such as heth-0-4 or heth-0-5 to the ISP. The device is assigned an IP address by the ISP through

DHCP.

Figure 4: Connecting the Interfaces on an NFX150-S1 Device

g100075

Internet

Optionally, you can obtain a SIM card from the ISP and connect the device through LTE.

NOTE: The LTE expansion module must be purchased separately.

For more information about SIM card activation, see the Getting Started with NFX150 available at:

https://www.juniper.net/documentation/en_US/release-independent/junos/information-products/pathway-pages/nfx-series/product/

NFX150-S1 Network Services Platform Quick Start

2. Connect the laptop to one of the front panel LAN ports such as heth-0-0,heth-0-1,heth-0-2, or heth-0-3. The laptop is assigned

an IP address by the DHCP server running on the interface.

3. Open a browser on your laptop, navigate to https://www.juniper.net, and verify your connectivity.

Next Steps

For information on downloading the image, provisioning virtual network functions (VNFs), and performing initial configuration

using the CLI, see the Getting Started with NFX150 available at:

https://www.juniper.net/documentation/en_US/release-independent/junos/information-products/pathway-pages/nfx-series/product/

Safety Warnings Summary

This is a summary of safety warnings. For a complete list of warnings, including translations, see the NFX150 documentation at

https://www.juniper.net/documentation/en_US/release-independent/junos/information-products/pathway-pages/nfx-series/product/.

WARNING: Failure to observe the following safety warnings can result in personal injury or death:

•Permit only trained and qualified personnel to install or replace device components.

•Perform only the procedures described in this Quick Start Guide and the NFX150 documentation. Other services

must be performed only by authorized service personnel.

•Before installing the device, read the planning instructions in the NFX150 documentation to make sure that the

site meets power, environmental, and clearance requirements for the device.

•Before connecting the device to a power source, read the installation instructions in the NFX150 documentation.

•The NFX150 device weighs approximately 13 lb (5.9 kg). Manually installing the device in a rack at a height above

60 in. (152.4 cm) requires two persons; one to lift the device and the second to install the mounting screws. To

prevent injury while lifting, keep your back straight and lift with your legs, not your back.

•If the rack has stabilizing devices, install them in the rack before mounting or servicing the device in the rack.

•Before installing or after removing an electrical component, always place it component-side up on an antistatic

mat placed on a flat, stable surface or in an antistatic bag.

•Do not work on the device or connect or disconnect cables during electrical storms.

•Before working on equipment that is connected to power lines, remove jewelry, including rings, necklaces, and

watches. Metal objects heat up when connected to power and ground and can cause serious burns or become

welded to the terminals.

Reference

•Technical Support

https://www.juniper.net/support/requesting-support.html

•Getting Started with NFX150

https://www.juniper.net/documentation/en_US/release-independent/junos/information-products/pathway-pages/nfx-series/product/

•NFX150 Hardware Guide

https://www.juniper.net/documentation/en_US/release-independent/junos/information-products/pathway-pages/nfx-series/product/

•Supported Transceivers

https://apps.juniper.net/hct/product/#prd=NFX150

NFX150-S1 Network Services Platform Quick Start

Juniper Networks, the Juniper Networks logo, Juniper, and Junos are registered trademarks of Juniper Networks, Inc. and/or its affiliates in the United States

and other countries. All other trademarks may be property of their respective owners. Juniper Networks assumes no responsibility for any inaccuracies in this

NFX150-S1 Network Services Platform Quick Start

Tabla de contenidos

Otros manuales de Enrutador de red de Juniper

Juniper

Juniper ACX2200 Instrucciones de instalación

Juniper

Juniper T640 Instrucciones de instalación

Juniper

Juniper T320 Manual de usuario

Juniper

Juniper MX240 Manual de usuario

Juniper

Juniper PTX1000 Instrucciones de instalación

Juniper

Juniper E SERIES BROADBAND SERVICES ROUTERS 11.3.X - E120 AND E320 HARDWARE GUIDE REV... Instrucciones de instalación

Juniper

Juniper MX204 Instrucciones de instalación

Juniper

Juniper MX10016 Manual de usuario

Juniper

Juniper LN2600 Manual de usuario

Juniper

Juniper PTX10003-80C Instrucciones de instalación

Juniper

Juniper EX9200 Series Hoja de especificaciones

Juniper

Juniper OCX1100 Instrucciones de instalación

Juniper

Juniper EX6210 Manual de usuario

Juniper

Juniper ACX5096 Manual de usuario

Juniper

Juniper JCS 1200 Manual de usuario

Juniper

Juniper T4000 - Instrucciones de instalación

Juniper

Juniper ACX1000 Manual de usuario

Juniper

Juniper E120 - RELEASE 11.1.X HARDWARE GUIDE... Instrucciones de instalación

Juniper

Juniper T640 Instrucciones de instalación

Juniper

Juniper J2300 Manual de usuario

Juniper

Juniper XRE200 - Manual de usuario

Juniper

Juniper EX9200 Series Hoja de especificaciones

Juniper

Juniper MX104 Instrucciones de instalación

Juniper

Juniper M40e Instrucciones de instalación

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad