Johnson Controls S321-IP Manual

24-10239-480 Revision F

December 2017

hardware installation

S321-IP

Network Controller

Johnson Controls

No part of this document may be reproduced without the prior permission of Johnson Controls.

If this document is translated from the original English version by Johnson Controls, all reasonable

endeavors will be used to ensure the accuracy of translation. Johnson Controls shall not be liable

for any translation errors contained herein or for incidental or consequential damages in connection

with the furnishing or use of this translated material.

Due to continuous development of our products, the information in this document is subject to

change without notice. Johnson Controls shall not be liable for errors contained herein or for

incidental or consequential damages in connection with furnishing or use of this material. Contents

of this publication may be preliminary and/or may be changed at any time without any obligation to

notify anyone of such revision or change, and shall not be regarded as a warranty.

Other Manufacturers’ Documentation

Johnson Controls does not duplicate documentation of other equipment manufacturers. When

necessary, Johnson Controls provides documentation that supplements that of other manufacturers.

When unpacking your equipment, keep all original manufacturer documentation for future

reference.

Technical Support

For factory technical support, Johnson Controls authorized field technicians or authorized dealer

representatives can contact Global Security Solutions Technical Support by phone at

(866) 893-0423 or (414) 524-1214, or by email at [email protected]. They

can also call the Field Support Center at (800) 524-1330 or (414) 524-5000 and use options 6, 1, 7.

End users and customers should contact their local Johnson Controls branch or authorized dealer

for any of their support needs (technical support, maintenance contracts, on-site field support,

P2000 Software Service Agreements, Service Partnerships, and so on). Visit

http://www.johnsoncontrols.com/location-finder to find your local Johnson Controls office.

For material returns contact the branch if the material was purchased through a Johnson Controls

branch or through the Product Sales Operations Team, if ordered through the Advanced Order

Management System (AOMS) and follow the RMA process; or contact the authorized dealer

representative where the material was purchased directly.

Acknowledgment

Metasys® and Johnson Controls® are trademarks of Johnson Controls. All other company and

product names are trademarks or registered trademarks of their respective owners.

Declarations of Conformity

United States: This equipment, S321-IP, has been tested and found to comply with the limits for a

Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

Canada: CAN ICES-3 (A)/NMB-3(A)

European Union: This product complies with the requirements of the EMC Directive.

This equipment must not be modified for any reason and it must be installed as stated in the

Manufacturer’s instructions. If this shipment (or any part thereof) is supplied as second-hand

equipment, equipment for sale outside the European Economic Area or as spare parts for either a

single unit or system, it is not covered by the Directives.

UNDERWRITERS LABORATORIES COMPLIANCE VERIFICATION SHEET

The following model number is listed under Underwriters Laboratories® (UL) 1076 for Proprietary

Burglar Alarm Units and Systems and UL 294 for Access Control Systems Units and Underwriters

Laboratories of Canada ULC/ORD-C1076-86.

S321-IP

When installed at the site the following requirements must be met to comply with these standards.

1. The S321-IP shall be mounted in subassembly S300-DIN-L or S300-DIN-S.

2. The tamper switch must be enabled at all times.

3. Transient protection devices that are installed must not be removed or defeated.

4. Do not connect equipment to an AC power source that is controlled by a switch.

5. The sole use of a class 2 transformer to power the S321-IP would not provide battery

standby power.

6. The RS485 reader interfaces were not investigated by Underwriters Laboratories.

7. For a UL 294 Listed system the following Listed readers may be used.

8. Model S321-IP must use a Class 2 direct plug-in transformer rated 120 VAC input and

24 VAC, 50 VA output from one of the following manufacturers:

Basler, part number BE116450CAA or BE116450AAA

Potter Electric Signal Co. (Amseco), model XR-2450LED

Revere Industries, model RT-2450SL/M

9. UL 294 Performance Levels

Destructive Attack Level I

Endurance Level IV

Line Security Level II

Standby Power Level I

Manufacturer Models

HID Corp. 30387, 31503, 31815, 31880, 32005, 32788, 32985

5355, 5365, 5395, 5405, 5455, 6005

All models may be followed by additional suffixes

Mercury Security Corp. MR-5

S321-IP Network Controller Hardware Installation

24-10239-480 Rev. F

S321-IP HARDWARE INSTALLATION

The S321-IP controller communicates with the host via Ethernet. It supports up

to two doors per unit and allows you to configure supervised 4-state inputs and

unsupervised 2-state inputs. The S321-IP controller provides power for the card

reader hardware; it does not provide power for the door locking hardware.

ABOUT THIS DOCUMENT

This document describes S321-IP hardware installation, basic operation, and

maintenance procedures. It is divided into the following sections:

•Unpacking the Equipment on page 1

•Tools Needed on page 1

•Mounting on page 2

•Description of Signals on page 5

•Cable Requirements on page 7

•Basic Commissioning on page 10

•The S321-IP User Interface on page 16

•Technical Specifications on page 19

•Maintenance on page 20

UNPACKING THE EQUIPMENT

Inspect the S321-IP shipping containers as soon as you receive them, with the

delivery agent present. If a container is damaged, open it immediately, inspect

the contents, and have the agent make note on the shipping document. Check

the purchase order against the packing slips to ensure the order is complete. If

the contents of a container are damaged, notify the carrier and your

Johnson Controls representative immediately. Report any discrepancies to your

Johnson Controls representative. Save the packing materials for possible return

shipments.

Your package should contain the S321-IP controller, connectors set, a CD

containing a set of user documentation, and this manual.

TOOLS NEEDED

Use a small, straight-blade screwdriver to secure wires in the terminal blocks.

S321-IP Network Controller Hardware Installation

24-10239-480 Rev. F

MOUNTING

You can mount the S321-IP controller on a flat surface, DIN rail, or in a

Johnson Controls’ approved enclosure (for example: S300-DIN).

For information on mounting the S321-IP in an enclosure, refer to the manual

provided with the enclosure.

To mount an S321-IP controller on a flat surface:

1. Fully extend the white clips located on the top and bottom of the

controller. You may need to remove the connectors.

2. Mount the controller to the surface with mounting screws.

3. Replace the connectors, if previously removed.

To mount an S321-IP controller on a DIN rail:

1. Fully extend the white clips located on the bottom of the controller.

You may need to remove the connectors.

2. Hook the controller on top of the rail and push in the clips.

Fully extended clips for

wall mount

(connectors are removed)

S321-IP

DIN rail

S321-IP

S321-IP Network Controller Hardware Installation

24-10239-480 Rev. F

3. If you need to remove a controller from the DIN rail, reverse the

mounting sequence (pull down the bottom clips, then pull the bottom

of the controller out and lift it up.)

Power Source Requirements

Line Voltage Information

If the facility is located in an area where power lines are subject to

frequent lightning strikes, verify with the electric company that the

building transformer is equipped with surge protectors. These, as well as

a “crowbar” type of protection, can be installed at the main service

entrance if the building transformer is not equipped with lightning

protection.

While lightning is one cause of power line transients, others can be

internal or external to the building environment. The general application

of transient surge suppression is low-cost insurance to ensure long life of

the equipment being installed.

Lithium Battery

The S321-IP contains a lithium battery that is used for realtime clock

backup. The lithium battery is shipped from the factory charged and

operational.

If there are no power outages, change the battery every five years. If a

power outage occurs, the battery life is approximately 30 days. Replace

with Panasonic part number CR2025 or equivalent.

Parameter Value

Power 24 W

Input voltage +12 to +28 VDC; 16 to 28 VAC

Nominal voltage +12 to +24 VDC; 16 to 24 VAC

Current 1 A at 24 V; 2 A at 12 V

Class 2 transformer (optional) See step 8 on the Underwriters Laboratories Compliance

Verification Sheet at the beginning of this manual.

S321-IP Network Controller Hardware Installation

24-10239-480 Rev. F

IMPORTANT: After you replace the lithium battery (recommended every five

years or after extended use), verify that the realtime clock is correct; otherwise,

you may need to adjust the time.

To replace the lithium battery:

1. Disconnect the 24 VDC power from the S321-IP.

2. Unscrew and open the plastic enclosure.

3. With a narrow (1/8 in.) blade, carefully pry up the battery until a

portion of the battery is out of the plastic holder.

4. With your free hand gently move the battery out of the holder while

keeping the battery pried up.

5. Dispose of the old battery according to local requirements.

6. Insert the new battery into holder.

IMPORTANT: The lithium battery is polarized. Ensure the side marked ‘+’ faces

out (that is, towards you).

7. Close the plastic enclosure and secure it with the screw.

8. Re-connect the power to the S321-IP.

CAUTION: Risk of Explosion.

Replace the battery with a lithium battery of the same type and

voltage rating. Dispose of the used battery in accordance with local,

national, and regional regulations. Failure to replace the battery with

one of the same type and voltage rating may result in an explosion

causing personal injury and property damage.

S321-IP Network Controller Hardware Installation

24-10239-480 Rev. F

DESCRIPTION OF SIGNALS

READER n

COM

TAMP

COM

SPARE

PWR FAIL

COM

TAMP

RDR n

STRIKE

RDR n

SHUNT

POWER RETURN

CAL RESISTOR

DATA1/Rs485+

DATA0/Rs485-

COM

POWER

GREEN LED

COM

RED LED

REX

COM

DOOR CONTACT

+12/24 VAC/VDC

RDR n PANEL

RDR n RDR n RDR n CAL POWER

RDR Request to

Exit Device

RDR Red Light

RDR Green Light

RDR Door

Reader

Calibration

Resistor

To the power

supply

RDR Door

Contact

RDR 1 General

Purpose Input 5

RDR 1 General

Purpose Input 6

RDR General

Purpose Input 3

RDR General

Purpose Input 4

RDR Shunt

RDR Strike

READER

RJ45

connector

READER

S321-IP Network Controller Hardware Installation

24-10239-480 Rev. F

Wiegand Input

Description of Signals – DATA0 and DATA1 from each reader,

complying with the Wiegand interface specification.

Reference – These signals are referenced to logic ground (COM).

Protection – Each signal has a 6 V transient voltage suppressor between

it and COM.

Input Points

Description of Signals – The following are internally pulled up inputs:

The allowable voltage range for these signals is 0-12 VDC.

Reference – These signals are referenced to their associated COM input.

Protection – Each signal is protected with series resistors and dual

clamping diodes.

External Circuits – 4-state operation requires two external resistors and

switch circuit connected between an input point and COM. 2-state

operation requires an external switch connected between an input point

and COM. For wiring details see Wiring Input Devices on page 8.

Output Points

Description of Signals – The following are open collector outputs, with

voltage range for these signals of 0-24 VDC, limited to 50mA:

IMPORTANT: These open collector outputs can be damaged by alternating

current (AC) potentials as low as 1 VAC. Connect the LED outputs only to direct

current (DC) loads up to 24VDC.

• Reader 1 Door

Contact

• Reader 1 REX

•Reader 1 Tamper

• Reader 1 Spare

• Reader 2 Door

Contact

• Reader 2 REX

•Reader 2 Tamper

• Reader 2 Spare

• Power Panel Fail

• Panel Tamper

• Reader 1 Red LED

• Reader 1 Green LED

• Reader 2 Red LED

• Reader 2 Green LED

Tabla de contenidos

Otros manuales de Controladores de Johnson Controls

Johnson Controls

Johnson Controls P2000 Manual

Johnson Controls

Johnson Controls M9200 Series Manual de usuario

Johnson Controls

Johnson Controls PENN ACT2 Manual de servicio

Johnson Controls

Johnson Controls PENN ACT2 Manual de servicio

Johnson Controls

Johnson Controls A350E Manual

Johnson Controls

Johnson Controls FX-PCG1621 Series Manual de usuario

Johnson Controls

Johnson Controls FX-PCA3611 Manual de usuario

Johnson Controls

Johnson Controls LC-AVMHTC1-0 Manual de usuario

Johnson Controls

Johnson Controls EDA-8102 Instrucciones de montaje

Johnson Controls

Johnson Controls M9216 Series Manual de usuario

Johnson Controls

Johnson Controls VA7820-GG-1 Series Manual de usuario

Johnson Controls

Johnson Controls FMS-1655L Manual de usuario

Johnson Controls

Johnson Controls TEC3010 Manual de usuario

Johnson Controls

Johnson Controls EasyIO FW-28 Manual de usuario

Johnson Controls

Johnson Controls LN-IO -1 Series Manual de usuario

Johnson Controls

Johnson Controls M9220-Bxx-3 Manual de usuario

Johnson Controls

Johnson Controls EDA-8000 Instrucciones de montaje

Johnson Controls

Johnson Controls CK721-A Instrucciones de montaje

Johnson Controls

Johnson Controls EDA-2040 Manual de usuario

Johnson Controls

Johnson Controls TEC2245-4 Manual de usuario

Johnson Controls

Johnson Controls METASYS ASC Manual de usuario

Johnson Controls

Johnson Controls FEC1611 Manual de usuario

Johnson Controls

Johnson Controls VA-9070 Series Manual de servicio

Johnson Controls

Johnson Controls Metasys FEC Series Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario