Johnson Controls EDA-8102 Instrucciones de montaje

Installation Sheet

Issue Date 0392

1. EDA-8102-1100 Electric Damper Actuator with counterclockwise

spring return, or

EDA-8102-1101 Electric Damper Actuator with clockwise spring

return

2. Two #10 mounting screws

3. Two isolator grommets

ςscrewdriver, flat blade, 1/4 to 5/16 inch and 1/8 inch tips

ςdrill, 5/32 inch (4 mm) drill bit, 1-1/4 inch hole saw

ςadjustable wrench

ςpliers

Figure 1: Electric Damper Actuator

1. Compatibility and torque:

ςuse on dampers having 10 to 12 mm (0.394 to 0.472 inch) square

or 7/16 to 1/2 inch (11 to 12.5 mm) round shafts

ςcompatible with Johnson Controls D-1300 Blade Dampers

ςdelivers 100 in.lb of stall torque

2. Mounting requirements:

ςmounts in any orientation

ςduct or wall must be 16 gauge (0.06 inch or 1.5 mm) or thicker

Note: Order the Universal Mounting Bracket (D-3153-105) to mount on

duct or wall less than 16 gauge.

EDA-8102 Electric Damper Actuator

Kit Includes

Tools Required

Installation

Overview

EDA-8102 Electric Damper Actuator

1. Follow NEC and local electrical codes.

2. Disconnect all power supplies.

3. Observe ranges and limitations for individual model.

4. Do not install the actuator in applications where its failure could result

in personal injury and/or loss of property.

5. Do not install if explosive vapors, corrosive vapors, or escaping gases

will be present.

6. Add protective control devices as needed to prevent undesirable

system failure modes.

For#10 Mounting

Screw(6places)

2.33

(59)

2x1.50

2x0.75

6.94

(235)

8.78

(223)

9.26

(235)

4.65

(118)

Figure 2: Top View Dimension inches

Mounting Caution

Pre-Mounting

EDA-8102 Electric Damper Actuator 3

4.34

(110)

6 in. min*

(3x 0.875)

for 1/2 in. conduit

Rubber Grommet

(2 Required)

* Six inch minimum required for cover removal, field wiring, and field adjustments.

Figure 3: End View Dimension inches

Note: Before starting the job, obtain the damper installation information

to use as a reference when mounting the actuator.

1. Locate the preferred driving blade on the damper.

2. Cut a 1-1/4 inch (32 mm) hole in the duct or wall over the driving

blade pin.

3. Attach the drive pin extension to the drive pin and secure using the

clip provided.

4. Firmly grasp the drive pin extension with a pliers and manually close

the damper blades.

RetainerClip

Drive PinExtension

Figure 4: Rotation.

5. Note which direction closes the damper, clockwise (CW) or

counterclockwise (CCW).

EDA-8102 Electric Damper Actuator

Figure 5: Removing Cover

6. Insert a screwdriver under the edge of the plastic cover to gently pry

off the cover. See Figure 5.

7. Verify the mode of operation for the proper model number from

Table 1.

Table 1: Operation Modes

Product Code

No. Drive

Type Travel

Time Spring

Return

EDA-8102-1100 proportional 180 second counterclockwise

EDA-8102-1101 proportional 180 second clockwise

Note: The actuator can be mounted in any orientation.

1. Position the actuator onto the drive pin extension so that the actuator

sits against the duct.

2. Use of the actuator’s center mounting slots with the isolation

grommets is the preferred mounting arrangement. If the duct or wall

is less than 16 gauge (0.06 inch or 1.5 mm), order and use the

Universal Mounting Bracket (D-3153-105).

Note: Because of eccentric motion of the actuator that occurs when using

shafts smaller than 10 mm (0.394 inch) square or 1/2 inch

(12.5 mm) round, use of the isolation grommets in the center

mounting slot is required.

3. Mark the location of the actuator's top and bottom mounting slots on

the duct or wall.

4. Remove the actuator and set aside.

5. Drill 5/32 inch (4 mm) holes in the duct or wall at the marked

locations.

Mounting

EDA-8102 Electric Damper Actuator 5

6. Slide the actuator onto the drive pin extension.

7. Secure the actuator to the wall or duct with the screws and insulators

included in the kit.

8. Tighten the two square-head screws on the actuator coupler.

Note: The cover should remain off until the wiring is completed.

CAUTION: Disconnect all power before wiring the actuator to

avoid electrical shock or damaging the equipment.

Conduit Opening Opening Covers

Figure 6: Conduit Openings

1. Insert the leads from the controller through one of the three openings.

2. Install the black plugs in the other two conduit openings. See

Figure 6.

InputVoltage

Common

24 VACInputPower

+15 VOutputSupply

Slidewire

AuxiliaryInput

ACCOMIN

+15

AUXIN

TB1

TB2

Figure 7: Wiring Connections

3. Connect the leads to Terminal Block 1 (TB1) as shown in Figure 7.

Wiring

EDA-8102 Electric Damper Actuator

TB1

TB2

DCW

DCCW

Figure 8: Jumper Locations

4. Set jumper at location W2 to match the control signal that will be

used. Jumper settings are defined in Table 2 below and shown in

Figure 8.

Table 2: Jumper Settings

Operating Mode W2 Jumper Setting

Voltage V

Current I

Slidewire V

Note: The EDA-8102 is factory set for 90° of rotation and a voltage

control signal of 1 to 9 VDC. To change these settings, see the

section Changing Rotation To Less Than 90° or the appropriate

signal calibration.

1. Apply power to the unit.

2. Refer to the controller's manual for directions on checking out a newly

installed device.

3. Use the controller to drive the actuator fully clockwise and

counterclockwise.

4. Verify that the damper blades fully open and close.

5. Install the plastic cover.

Checkout

Procedure

EDA-8102 Electric Damper Actuator 7

The EDA-8102 is factory set for 90° of rotation and a control signal of 1

to 9 VDC. If the amount of rotation or the control signal must be changed

from factory settings, use the following procedures. Refer to Figure 7 for

the location of the potentiometer and terminal blocks in the procedures.

Figure 9: Rotation Setting

1. Verify jumper W2 is set to the voltage (V) position.

2. Verify jumper W1 is set in the desired position:

DCW for clockwise driven rotation.

DCCW for counterclockwise driven rotation.

Note: Spring return direction is NOT reversible.

3. Turn the offset potentiometer (R39) to its mid-position.

4. Turn the span potentiometer (R35) fully counterclockwise.

5. Turn the CCW potentiometer (R36) fully clockwise.

6. Connect a jumper from terminal IN (TB1) to terminal +15 (TB2) as

shown in Figure 9. The actuator rotates until the end stop is reached.

7. Slowly adjust the stroke potentiometer (R37) until the actuator rotates

to the desired end stop position.

8. Remove the jumper between terminal IN and +15.

Field Adjustments

Changing Rotation

to Less Than 90°

Span

(R35)CCW

(R36)

Stroke

(R37)Offset

(R39)

TB1

TB2

COM

+15

AUXIN

TB1TB2

DCW

DCCW

EDA-8102 Electric Damper Actuator

COM

IN+15 +1

AUXI

TB1TB2

Figure 10: End Stop Connection

9. Connect terminal IN to COM (TB1) as shown in Figure 10. The

actuator will rotate until the end stop is reached.

10. Slowly adjust the CCW potentiometer (R36) until the actuator rotates

to the desired position.

11. Remove the connection between terminals IN and COM (TB1).

Note: Calibration of offset and span is required after changing rotation.

Depending on controller application, proceed with the appropriate

calibration procedure.

EDA-8102 Electric Damper Actuator 9

Span

(R35)

CCW

(R36)

Stroke

(R37) Offset

(R39)

TB1TB2

0 to 15 VDC

Input

Common

Figure 11: Voltage Mode Connection

1. Verify that jumper W2 is set to the voltage (V) position.

2. Turn the span potentiometer (R35) fully clockwise.

3. Connect the input voltage (0 to 15 VDC) between terminals IN (+) and

COM (-) on TB1.

4. Apply the starting voltage.

5. Adjust the offset potentiometer (R39) until the actuator just begins to

move.

6. Apply the full span voltage.

7. Adjust the span potentiometer (R35) until the actuator reaches its

desired limit.

8. Remove external connections and install the cover.

Voltage Mode

Calibration

EDA-8102 Electric Damper Actuator

Span

(R35)

CCW

(R36)

Stroke

(R37) Offset

(R39)

TB1

TB2

0 to 20 mA

Input

Common

Figure 12: Current Mode Connection

1. Verify that jumper W2 is set to the current (I) position.

2. Turn the span potentiometer (R35) fully clockwise.

3. Connect the input current (0 to 20 mA) to terminals AUXIN (+) on

TB2 and COM (-) on TB1.

4. Apply the starting current.

5. Adjust the offset potentiometer (R39) until the actuator just begins to

move.

6. Apply full current.

7. Adjust the span potentiometer (R35) until the actuator reaches its

desired limit.

8. Remove external connections and install the cover.

Current Mode

Calibration

Otros manuales para EDA-8102

Otros manuales de Controladores de Johnson Controls

Johnson Controls

Johnson Controls MP8 20 Series Manual de usuario

Johnson Controls

Johnson Controls VA7820-HG*-2 Series Manual de usuario

Johnson Controls

Johnson Controls CGM09090 Manual de usuario

Johnson Controls

Johnson Controls EDA-8100 Instrucciones de montaje

Johnson Controls

Johnson Controls Penn P216 Manual de usuario

Johnson Controls

Johnson Controls LC-AVMHTC1-0 Manual de usuario

Johnson Controls

Johnson Controls FX-PCV1930 Manual de usuario

Johnson Controls

Johnson Controls FMS-2000C Manual de usuario

Johnson Controls

Johnson Controls P2000 Manual

Johnson Controls

Johnson Controls UZC-256 Manual de usuario

Johnson Controls

Johnson Controls FX-PCV18 Series Manual de usuario

Johnson Controls

Johnson Controls RA-3 Series Manual del propietario

Johnson Controls

Johnson Controls S321 Suplemento

Johnson Controls

Johnson Controls PENN P28 Manual de usuario

Johnson Controls

Johnson Controls VA-8122 Manual de servicio

Johnson Controls

Johnson Controls EDA-8000 Instrucciones de montaje

Johnson Controls

Johnson Controls NIE29 Series Manual de usuario

Johnson Controls

Johnson Controls VA9310 Series Manual de usuario

Johnson Controls

Johnson Controls LN Series Manual de usuario

Johnson Controls

Johnson Controls tyco PowerSeries Neo Manual de usuario

Johnson Controls

Johnson Controls MS-FEC2611 Series Manual de usuario

Johnson Controls

Johnson Controls tyco iSTAR Edge G2 Manual de usuario

Johnson Controls

Johnson Controls Metasys VMA1610 Manual de usuario

Johnson Controls

Johnson Controls penn TC3B21 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario