Johnson Controls PCA3613 Manual de usuario

PCA3613 Advanced Application

Programmable Controller Installation

Instructions

Application

The PCA3613 controller runs pre-engineered and user-programmed applications and provide

the inputs and outputs required to monitor and control a wide variety of HVAC and other facility

equipment.

PCA36 controllers operate on an RS-485 BACnet® MS/TP Bus and integrate into Johnson Controls®

and third-party BACnet systems.

PCA36 controllers include an integral real-time clock, which enables the controllers to monitor and

control schedules, calendars, and trends, and operate for extended periods of time as stand-alone

controllers when offline from the system network.

Communications protocols

By default, the controllers communicate using the standard BACnet MS/TP protocol based on the

ANSI/ASHRAE 135-2012. The BACnet protocol is a standard for ANSI, ASHRAE, and the International

Standards Organization (ISO) for building controls.

North American Emissions Compliance

United States

This equipment has been tested and found to comply with the limits for a Class A digital device

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when this equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area may cause harmful

interference, in which case the users will be required to correct the interference at their own

expense.

Canada

This Class (A) digital apparatus meets all the requirements of the Canadian Interference-Causing

Equipment Regulations.

Cet appareil numérique de la Classe (A) respecte toutes les exigences du Règlement sur le

matériel brouilleur du Canada.

Installation

Observe the following guidelines when installing a PCA3613:

• To minimize vibration and shock damage, transport the controller in the original container.

• Verify that all parts shipped with the controller.

• Do not drop the controller or subject it to physical shock.

Part No. 24-10143-1175 Rev C

2019-03-22 (barcode for factory use only)

CH-PCA3613

*24101431175C*

Parts included

• One PCA3613 controller with removable terminal blocks

• One installation instructions sheet

Materials and special tools needed

• Three fasteners appropriate for the mounting surface (M4 screws or #8 screws)

• One 23 cm (9.125 in.) or longer piece of 35 mm DIN rail and appropriate hardware for DIN rail

mount (only)

• Small straight-blade screwdriver for securing wires in the terminal blocks

Mounting

Observe the following guidelines when mounting a PCA3613:

• Ensure the mounting surface can support the controller, DIN rail, and any user-supplied

enclosure.

• Mount the controller horizontally on 35 mm DIN rail whenever possible.

• Mount the controller in the correct mounting position (Figure 1).

• Whenever possible in wall-mount applications, mount the controller on a hard, even surface.

• Use shims or washers to mount the controller securely and evenly on the mounting surface.

• Mount the controller in an area free of corrosive vapors and observe the ambient conditions

requirements in Technical specifications.

• Provide sufficient space around the controller for cable and wire connections, easy cover

removal, and good ventilation through the controller (50 mm [2 in.] minimum on the top,

bottom, and front of the controller).

• Do not mount the controller on surfaces prone to vibration, such as ductwork.

• Do not mount the controller in areas where electromagnetic emissions from other devices or

wiring can interfere with controller communication.

Observe these additional guidelines when mounting a PCA3613 in a panel or enclosure:

• Mount the controller so that the enclosure walls do not obstruct cover removal or ventilation

through the controller.

• Mount the controller so that the power transformer and other devices do not radiate excessive

heat to the controller.

• Do not install the controller in an airtight enclosure.

PCA3613 Advanced Application Programmable Controller Installation Instructions2

Figure 1: Controller mounting positions

DIN rail mount applications

Mounting the PCA3613 controller horizontally on 35 mm DIN rail is the preferred mounting

method.

To mount a controller on 35 mm DIN rail, complete the following steps:

1. Securely mount a 23 cm (9.125 in.) or longer section of 35 mm DIN rail, horizontally and

centered in the desired space, so that the controller mounts in the position shown in Figure 1.

2. Pull the two bottom mounting clips outward from the controller to the extended position

(Figure 2).

3. Hang the controller on the DIN rail by the hooks at the top of the (DIN rail) channel on the back

of the controller (Figure 2), and position the controller snugly against the DIN rail.

4. Push the bottom mounting clips inward (up) to secure the controller on the DIN rail.

To remove the controller from the DIN rail, pull the bottom mounting clips out to the extended

position and carefully lift the controller off the DIN rail.

Wall mount applications

To mount a PCA3613 directly on a wall or other flat vertical surface, complete the following steps:

1. Pull the two bottom mounting clips outward and ensure they are locked in the extended

position as shown in Figure 2.

2. Mark the mounting hole locations on the wall using the dimensions in Figure 2 and one of the

mount positions shown in Figure 1. Or hold the controller up to the wall or surface in a proper

mount position and mark the hole locations through the mounting clips.

3. Drill holes in the wall or surface at the marked locations, and insert appropriate wall anchors in

the holes (if necessary).

4. Hold the controller in place, and insert the screws through the mounting clips and into the

holes (or anchors). Carefully tighten all of the screws.

Important: Do not overtighten the mounting screws. Overtightening the screws may

damage the mounting clips.

3PCA3613 Advanced Application Programmable Controller Installation Instructions

Figure 2: Back of Controller showing extended mounting

clips, DIN rail channel, and mounting dimensions, mm (in.)

PCA3613 Advanced Application Programmable Controller Installation Instructions4

PCA3613 physical features

Figure 3: PCA3613 physical features

Table 1: Physical features

Callout Physical feature: description and references

1Analog Output (AO) Terminal Block: Can be defined as Voltage Analog Output (0–10

VDC) or Current Analog Output (4–20 mA) (see Table 3)

2Device Address DIP Switch Block (see Setting the Device Addresses)

3Mounting clip

4Binary Outputs (BO) Terminal Block: 24 VAC Triac (see Table 3)

524 VAC, Class 2/SELV Supply Power Terminal Block (see Supply power terminal block)

6Cover Lift Tab (One of Two)

7FC Bus Terminal Block (see FC bus terminal block )

8SA Bus Terminal Block (see SA bus terminal block)

9Sensor Port: (SA Bus) RJ-12 6-Pin Modular Jack (see Sensor port )

10 Binary Input (BI) Terminal Block: Dry Contact Maintained or Pulse Counter/Accumulator

Mode (see Terminal wiring guidelines, functions, ratings, and requirements)

11 Universal Inputs (UI) Terminal Block: Can be defined as Voltage Analog Input (0–10

VDC), Current Analog Input (4–20 mA), Resistive Analog Inputs (0–600k ohms), or Dry

Contact Binary Input (see Input and Output wiring guidelines)

5PCA3613 Advanced Application Programmable Controller Installation Instructions

Table 1: Physical features

Callout Physical feature: description and references

12 End-of-Line (EOL) Switch (see Setting the End-of-Line (EOL) switch)

13 LED Status Indicators (see Table 8)

14 FC Bus Port (RJ-12 6-pin Modular Jack)

Wiring

CAUTION

Risk of Electric Shock:

Disconnect the power supply before making electrical connections to avoid electric shock

CAUTION

Mise En Garde: Risque de décharge électrique

Débrancher l'alimentation avant de réaliser tout raccordement électrique afin d'éviter tout risque de

décharge électrique.

CAUTION

Risk of Property Damage:

Do not apply power to the system before checking all wiring connections. Short circuited or improperly

connected wires may result in permanent damage to the equipment.

CAUTION

Mise En Garde: Risque de dégâts matériels

Ne pas mettre le système sous tension avant d'avoir vérifié tous les raccords de câblage. Des fils

formant un court-circuit ou connectés de façon incorrecte risquent d'endommager irrémédiablement

l'équipement.

Important: Do not exceed the controller electrical ratings. Exceeding controller electrical

ratings can result in permanent damage to the controller and void any warranty.

Important: Use copper conductors only. Make all wiring in accordance with local, national,

and regional regulations.

Important: Electrostatic discharge can damage controller components. Use proper

electrostatic discharge precautions during installation, setup, and servicing to avoid damaging

the controller.

PCA3613 Advanced Application Programmable Controller Installation Instructions6

For detailed information about configuring and wiring an MS/TP bus, FC bus and SA bus, refer to

the following documents depending on your system (FX or BCPro): MS/TP Communications Bus for

the BCPro™ System Technical Bulletin (LIT-12011908) or FX-PC Series Controllers MS/TP Communications

Bus Technical Bulletin (LIT-12011670).

Terminal blocks and bus ports

See PCA3613 physical features for terminal block and bus port locations on the PCA3613 controller.

Observe the following guidelines when wiring a PCA3613 controller.

Input and Output terminal blocks

The fixed input terminal blocks are located on the bottom of the controller, and the output terminal

blocks are located on the top of the controller. See Table 3 for more information about I/O terminal

functions, requirements, and ratings.

FC bus terminal block

The FC Bus terminal block is a blue, removable, 4-terminal plug that fits into a board-mounted jack.

Wire the removable FC bus terminal block plugs on the controller, and other controllers in a daisy-

chain configuration using 3-wire twisted, shielded cable as shown in Figure 4. For more information

about the FC Bus terminal function, requirements, and ratings, see Table 5.

Figure 4: FC bus terminal block wiring

Note: The FC bus Shield (SHLD) terminal is isolated and can be used to connect (daisy chain)

the shields for FC bus wiring.

SA bus terminal block

The SA Bus terminal block is a brown, removable, 4-terminal plug that fits into a board-mounted

jack.

Wire the removable SA Bus terminal block plugs on the controller, and other SA bus devices in

a daisy-chain configuration using 4-wire twisted, shielded cable as shown in Figure 5. For more

information about the SA Bus terminal function, requirements, and ratings, see Table 5.

7PCA3613 Advanced Application Programmable Controller Installation Instructions

Figure 5: SA bus terminal block wiring

Note: The SA PWR terminal supplies 15 VDC. The SA PWR terminal can be used to connect

(daisy chain) the 15 VDC power leads on the SA bus.

FC bus port

The FC bus port on the front of the controller is an RJ-12, 6-position modular jack that provides a

connection for the Mobile Access Portal (MAP) Gateway, the FX-BTCVT Bluetooth® Commissioning

Converter, or the FX-ZFR/ZFR Pro Wireless Field Bus Router.

The FC bus port is connected internally to the FC bus terminal block. For more information about

the FC Bus port functions, requirements, and ratings, see Table 5. The FC bus port pin assignment is

shown in Figure 6.

Note:

• The MAP Gateway serves as a replacement for the BTCVT, which is no longer available for

purchase, but continues to be supported.

Figure 6: Pin number assignments for sensor, SA bus, and FC bus ports on Controllers

PCA3613 Advanced Application Programmable Controller Installation Instructions8

Sensor port

The Sensor (SA Bus) port on the bottom of the controller is an RJ-12, 6-position modular jack that

provides a connection for MAP Gateway, the Bluetooth® Commissioning Converter (BTCVT), the VAV

Balancing Tool, specified network sensors, or other SA Bus devices with RJ-12 plugs.

A DIS1710 Local Controller Display also can be connected to the SA Bus port.

The Sensor port is connected internally to the SA bus terminal block. For more information about

the Sensor port functions, requirements and ratings, see Table 5. The Sensor Port pin assignment is

shown in Figure 6.

Note: The MAP Gateway serves as a replacement for the BTCVT, which is no longer available

for purchase, but continues to be supported.

Supply power terminal block

The 24 VAC supply power terminal block is a gray, removable, 3-terminal plug that fits into a board-

mounted jack on the top right of the controller.

Wire the 24 VAC supply power wires from the transformer to the HOT and COM terminals on the

terminal plug as shown in Figure 7. Do not use the middle terminal on the supply power terminal

block. See Table 5 for more information about the Supply Power Terminal Block.

Figure 7: 24 VAC supply power terminal block wiring

Note: The supply power wire colors may be different on transformers from other

manufacturers. Refer to the transformer manufacturer’s instructions and the project

installation drawings for wiring details.

Important: Connect 24 VAC supply power to the controller and all other network devices so

that transformer phasing is uniform across the network devices. Powering network devices

with uniform 24 VAC supply power phasing reduces noise, interference, and ground loop

problems. The controller does not require an earth ground connection.

9PCA3613 Advanced Application Programmable Controller Installation Instructions

Termination diagrams

A set of Johnson Controls termination diagrams provides details for wiring inputs and outputs to

the controllers. See the figures in this section for the applicable termination diagrams.

Table 2: Termination details

Type of field

device

Type of

Input/

Output

Termination diagrams

Temperature

Sensor

Voltage

Input -

External

Source

Voltage

Input -

Internal

Source

Voltage

Input (Self-

Powered)

PCA3613 Advanced Application Programmable Controller Installation Instructions10

Tabla de contenidos

Otros manuales de Controladores de Johnson Controls

Johnson Controls

Johnson Controls M9108-A-1N Series Manual de usuario

Johnson Controls

Johnson Controls T-5800 Series Manual de uso y cuidado

Johnson Controls

Johnson Controls Facility Explorer FX40 Manual de usuario

Johnson Controls

Johnson Controls JCRL120PW Manual de usuario

Johnson Controls

Johnson Controls MP8 20 Series Manual de usuario

Johnson Controls

Johnson Controls M9108-GG 1N Series Manual de usuario

Johnson Controls

Johnson Controls FX-PCV1656 Manual de usuario

Johnson Controls

Johnson Controls F4-CV Series Manual de usuario

Johnson Controls

Johnson Controls TC-8902 Manual de usuario

Johnson Controls

Johnson Controls TEC3010 Manual de usuario

Johnson Controls

Johnson Controls Tyco Kantech KT-400 Guía de inicio rápido

Johnson Controls

Johnson Controls VA-7700 Series Manual de usuario

Johnson Controls

Johnson Controls V-4000-1 Manual de usuario

Johnson Controls

Johnson Controls VFD66 Series Manual de usuario

Johnson Controls

Johnson Controls FX-PCA4911 Manual de usuario

Johnson Controls

Johnson Controls VG1600 Series Manual de usuario

Johnson Controls

Johnson Controls TEC3000 Series Manual de usuario

Johnson Controls

Johnson Controls FAC2612-2 Manual de usuario

Johnson Controls

Johnson Controls CK721-A Instrucciones de montaje

Johnson Controls

Johnson Controls SE-ZEC510-1 Manual de usuario

Johnson Controls

Johnson Controls VA-77 Series Manual de usuario

Johnson Controls

Johnson Controls FX30E Manual de servicio

Johnson Controls

Johnson Controls M9203-AG-2 Series Manual de usuario

Johnson Controls

Johnson Controls A19ZBA Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario