Jensen VM9424 Manual de usuario

VM9424

VM9424 Head Unit

Left and Right Double DIN

Mounting Brackets

Double DIN Half Sleeve Install Bracket

Remote Control with Battery

Two Custom Cosmetic Trim Rings

Parking Brake Wire

Hardware Bag

Speaker Output Harness

Power Input Harness

2 x Accessory Harness

Installation Guide

What’s in the Box

You will need these tools and supplies to

install your VM9424:

• Torx type, ﬂat-head and Philips

screwdrivers

• Wire cutters and strippers

• Tools to remove existing radio (screw

driver, socket wrench set or other tools)

• Electrical tape

• Crimping tool

• Volt meter/test light

• Crimp connections

• 18 gauge wire for power connections

• 16 – 18 gauge speaker wire

Tools and Supplies

Installation Guide

WARNING! Never install this unit where operation and viewing could interfere with

safe driving conditions.

Optional Equipment

• BTM10: Allows you to connect to a Bluetooth enabled cell phone or other device.

• Rear Camera

Disconnecting the Battery

To prevent a short circuit, be sure to turn off the ignition and remove the negative (-) battery cable prior to in-

stallation.

NOTE: If the VM9424 is to be installed in a car equipped with an on-board drive or navigation computer, do

not disconnect the battery cable. If the cable is disconnected, the computer memory may be lost. Under these

conditions, use extra caution during installation to avoid causing a short circuit.

Replacing the Fuse

When replacing the fuse, use a new 15A replacement fuse. Using a fuse with an improper rating could damage

the unit and cause a ﬁre.

ISO-DIN Installation

This unit is designed to ﬁt into a 2.0 DIN dashboard opening, found in many imported cars. The unit has

threaded holes in the chassis side panels which may be used with the original factory mounting brackets of

some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to mount the radio to the dashboard.

Please consult with your local car stereo specialty shop for assistance on this type of installation.

Remove the existing factory radio from the dashboard or

center console mounting. Save all hardware and brackets

as they will be used to mount the new radio.

Remove the factory mounting brackets and hardware from

the existing radio and attach them to the new radio.

CAUTION: Do not exceed M5 X 6MM screw size. Longer

screws may damage components inside the chassis.

Place the radio in front of the dashboard opening so the

wiring can be brought through the mounting sleeve. Fol-

low the wiring diagram carefully and make certain all con-

nections are secure and insulated with wire nuts or electri-

cal tape. After completing the wiring connections, plug the

ISO connectors into the mating sockets on the rear of the

chassis. Turn the unit on to conﬁrm operation (vehicle ignition switch must be “on”). If the unit does not

operate, re-check all wiring until the problem is corrected.

Mount the new radio assembly to the dashboard or center console using the reverse procedure in step 1.

CAUTION! Be careful not to damage the car wiring.

NOTE: It is the end-users responsibility to install and operate this unit in a manner in accordance with local,

state and federal laws. The PARKING BRAKE wire MUST BE CONNECTED as directed in the manual.

CAUTION: Do not block the cooling fan exit. If blocked, the unit may overheat and become damaged.

/ SRC

NAV

Press Audio

VOLMute

AV IN

VM9424

Multimedia Receiver

Installation Using Half-Sleeve

Install half-sleeve in the dashboard.

a. Install adapter if necessary (optional).

b. Install half-sleeve into adapter or dashboard (use only

the supplied screws). Do not force the sleeve into the

opening or cause it to bend or bow.

WARNING! Only connect the unit to a 12-volt power

supply with proper grounding.

c. Locate the series of bend-tabs along the top, bottom

and sides of the mounting sleeve. With the sleeve fully

inserted into the dashboard opening, bend as many of

the tabs outward as necessary so that the sleeve is

ﬁrmly secured to the dashboard.

Use the M5 x 6 screws (provided) to install the mounting

brackets to each side of the radio using the holes indicated

in the diagram. DO NOT USE OTHER SCREWS.

Place the radio in front of the dashboard opening so the

wiring can be brought through the mounting sleeve.

Complete wiring as illustrated in the wiring diagram. Once

the wiring is complete, reconnect the battery negative

terminal. If there is no ACC available, connect the ACC lead

to the power supply with a switch.

CAUTION! Be careful not to damage the car wiring.

After completing the wiring connections, turn the unit on

to conﬁrm operation (ignition switch must be on). If unit does

not operate, recheck all wiring until problem is corrected.

Once proper operation is achieved, turn off the ignition

switch and proceed with ﬁnal mounting of the chassis.

a. Connect wiring adapter to existing wiring harness.

b. Connect antenna lead.

c. Carefully slide the radio into the half-sleeve, making

sure it is right-side-up. Use the supplied screws to at-

tach the radio to the half sleeve.

Using the Cosmetic Trim Ring

Two cosmetic trim rings are packaged with the head unit for

installation ﬂexibility. This unit will ﬁt into most import dashes

with little or no modiﬁcation to the dash board/cavity. Some US

domestic vehicle dashes will accept a Double-DIN chassis, but

there is usually a small gap between the radio and dash piece af-

ter installation is complete. In this case, use the appropriate trim

ring to conceal any gaps that may be present.

NOTE: For proper operation of the CD/DVD player, the chassis

must be mounted within 30° of horizontal. Make sure the unit

is mounted within this limitation.

DASHBOARD

TAB

Step 1-b

Step 1-c

Step 2

Step 5-c

MOUNTING

SLEEVE

TRIM RING

Wiring Diagram

IMPORTANT: Incorrect wiring connections can damage the unit. Follow the wiring instructions carefully, or have the installation handled by an

experienced technician.

Need Help? For technical assistance, call the Jensen customer support line at 1-800-323-4815.

MediaLink USB

(Included)

jLink USB iPod Interface Cable

(Sold Separately) - Required for iPod

Video Viewing through Head Unit

FUSE 15A

Connect to

Optional BTM10

(sold Separately)

NOTE: Steering Wheel Control (SWC)

Requires PAC SWI-PS Interface

Adapter, Sold Separately

Additional Monitors

Sold Separately

Backup Camera

Sold Separately

Connect to optional

XM Satellite Radio

Receiver with Antenna

Parking Brake

(Pink Wire)

910

11 12

13 14

15 16

RL-

FL-

RL+

FL+

RR-

FR-

RR+

FR+

P.ANT

REVERSE

P.CONT

MUTE

ACC

ILLUM

GND

B+

GREEN/BLACK

WHITE/BLACK

GREEN

WHITE

VIOLET/BLACK

GRAY/BLACK

VIOLET

GRAY

BLUE

GREEN/WHITE

BLUE/WHITE

BROWN

RED

ORANGE

BLACK

YELLOW

Otros manuales para VM9424

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de vídeo para coche de Jensen

Jensen

Jensen CR271ML Instrucciones de funcionamiento

Jensen

Jensen JMV111 - DVD Player With LCD Monitor Manual de usuario

Jensen

Jensen VX7023 Manual de usuario

Jensen

Jensen CM7MIR Instrucciones de funcionamiento

Jensen

Jensen JENHR1D Instrucciones de instalación y funcionamiento

Jensen

Jensen VX3020 Manual de usuario

Jensen

Jensen CAR710X Instrucciones de funcionamiento

Jensen

Jensen VM9224BT Manual de usuario

Jensen

Jensen VM9115 Manual de usuario

Jensen

Jensen CMR2720 Instrucciones de funcionamiento

Jensen

Jensen VM9512HD Manual de usuario

Jensen

Jensen CMM720 Instrucciones de funcionamiento

Jensen

Jensen CAR68 Instrucciones de funcionamiento

Jensen

Jensen CAR910W Instrucciones de funcionamiento

Jensen

Jensen VM9022 - DVD Player With LCD Monitor Manual de usuario

Jensen

Jensen CMR270 Instrucciones de funcionamiento

Jensen

Jensen Mobile Multimedia AM/FM/DVD Receiver VM9410 Manual de usuario

Jensen

Jensen CAR110W Instrucciones de funcionamiento

Jensen

Jensen VM9022HDN - Touch Screen Double Din MultiMedia... Manual de usuario

Jensen

Jensen VM9026 Manual de usuario

Jensen

Jensen CAR689 Instrucciones de funcionamiento

Jensen

Jensen VR187 Manual de usuario

Jensen

Jensen Mobile Multimedia AM/FM/DVD Receiver VM9410 Manual de usuario

Jensen

Jensen VM9114 Manual de usuario

Manuales populares de Sistema de vídeo para coche de otras marcas

Stinger

Stinger HEIGH10 RB10RAM13B Manual de usuario

Eonon

Eonon E1057 Manual de usuario

Milion

Milion D2223 Manual de usuario

Metra Electronics

Metra Electronics 99-8153 Manual de usuario

Voxx Electronics

Voxx Electronics HR8MA1 Manual de usuario

Axxera

Axxera AV604Bi Manual de usuario

Clarion

Clarion NX706E Manual de usuario

Pyle view

Pyle view PLDN74BTi Manual de usuario

Clarion

Clarion NX602 Manual de usuario

PowerAcoustik

PowerAcoustik PTID-5850N Manual de usuario

RCA

RCA DRC6296 - Twin 9" Mobile DVD System Guía del usuario

Lanzar

Lanzar SVDVD5 Manual de usuario

Kia

Kia MTXM100YPPE Manual de usuario

Eonon

Eonon E1060 Manual de usuario

Macrom

Macrom M-AN900 Manual de usuario

Hyundai

Hyundai BAPE-L3000N Manual de usuario

r.LiNK

r.LiNK RL2-UCON8-SM Manual de usuario

Blaupunkt

Blaupunkt DVP 01C Manual de usuario