iWatSkate iCruiser Manual de usuario
MANUAL
EN · ES · FR · IT · PT
ENGLISH4 |
welcome to styleMotion
Congratulations!
You can now enjoy your iWatSkate, but before jumping onto StyleMotion, we recommend that you
carefully read this manual. In it, you will find all the necessary steps to safely enjoy the iWatSkate.
be prepared before riding
- Please, wear a safety helmet and other protective equipment at all times to avoid any possible injuries.
- For your first ride, make sure to have someone’s help to avoid injuries.
* Bear in mind the user’s weight, riding habits, gradeability as well as the road condition can aect the
speed and the battery range. Try to maintain a stable speed, avoid sudden breaks and ride on flat surfaces
to make the battery last longer.
for safety reasons, please refrain from...
- Riding the board in dangerous surfaces such as sand, mud, ice, puddles and slippery or uneven ground.
The board is designed to be used on smooth and dry surfaces, without debris, sand, leaves, rocks or
gravel.
- Riding the board in rain, snow or other hazardous weather.
- Submerging the board in water.
- Touching the metal parts such as the motor hub or the truck to avoid getting burned.
- Using the board if the battery (of either the board or the remote) is low.
- Doing stunts or tricks while riding on the board. It is not designed to support tricks, jumping, stunts or
racing.
- Riding more than one person at a time.
- Riding at night or with poor lighting.
- Riding the board indoors.
- Riding near swimming pools or steps.
- Hitching a ride with a vehicle.
- Using headphones or a mobile phone when riding the board.
- Riding the board downhill, especially at a speed you cannot safely control.
warning
- Be careful not to get clothes, hands, hair or any other body part caught in the wheels.
- Respect the weight limitations.
- Always ride the board paying attention and being really cautious. Always maintain a safe distance with
other vehicles and make sure to keep a good posture.
- This skateboard is a wireless-controlled device. Please avoid riding the board in a signal-polluted
environment since it can interfere with the frequency and cause a signal loss.
- This product is designed for children over 7 years.
ENGLISH
| 5ENGLISH
charger and battery use
- The charger should be regularly checked for potential damage to the cord, plug and other parts. In case of any
damage, STOP using the charger until it is repaired or replaced.
- Do not charge for more than 6 hours at a time.
- Only use the provided charger. Using any other charger may cause a fire.
- The charger should always be operated by an adult.
- Always unplug the charger and disconnect it from the board when it’s not being used.
- Do not operate the charger near any flammable materials or environment.
- Please charge the battery once a month if the skateboard is not going to be used.
THIS PRODUCT IS A HIGH-SPEED ELECTRONIC MOTORIZED DEVICE. RIDING THE BOARD CAN BE A
DANGEROUS ACTIVITY. IT COULD POTENTIALLY CAUSE SERIOUS INJURY OR DEATH. PLEASE RIDE IT
WITH PROPER SAFETY PRECAUTIONS. USE AT YOUR OWN RISK.
- Always read and understand the user manual before riding.
- Ride the board with extreme precaution as warned in this user manual.
- Please, wear a safety helmet and other protective equipment at all times to avoid any possible injuries.
- The battery may get damaged and battery life reduced if exposed to extreme temperatures or submitted
to an improper use.
- Always ride the board in a controlled environment.
PLEASE KEEP THE INSTRUCTIONS FOR FUTURE REFERENCE
AS THEY MAY CONTAIN IMPORTANT USER INFORMATION.
THIS TYPE OF DEVICE MIGHT BE PROHIBITED BY LOCAL LAW OR REGULATIONS.
PLEASE, OBEY LOCAL REGULATIONS AND USE THE BOARD AT ALLOWED AREAS.
- DO NOT expose the board to heat sources, direct sunlight during long periods of time or other high
temperature environments.
- Always charge the board with the supplied adaptor and charge the remote control with a standard USB
charger.
- Avoid dropping or subjecting the battery to high impacts.
- DO NOT disassemble or attempt to repair any parts of the battery.
- CHARGE the battery frequently, even if the battery level isn’t low in order to improve battery life.
- Charge the battery at least once a month if the board isn’t going to be used for a long period of time.
Leaving the battery uncharged for longer periods of time will result in a decreased battery life.
- DO NOT charge the battery for more than 6 hours at a time.
- DISCONNECT the plug from the mains when unsupervised.
- NEVER dispose of batteries in the garbage. Always take used batteries to your local battery-recycling centre.
Please read the instructions and warnings before using this product. Improper use of this
product may result in product damage, overheating, fire, explosion or toxic fumes, for which
the manufacturer will not be responsible.
CAUTION! LITHIUM-ION BATTERIES INSIDE
ENGLISH6 |
diagram
Truck
Deck
Battery
Housing
Lithium-ion
Batteries
Dual Motor
Single
Motor
Upgrading Port*
Pair Button
Charging Port
*The upgrading port is only for our technical service, not for user use.
| 7ENGLISH
remote control
Lights 1& 2: indicate the three speed modes:
1) ECO ( Green)
2) STREET ( Red)
3) PRO ( Green and Red)
When the board is OFF, or the remote’s connec-
tion with the board is disconnected:
Lights 1& 2will flash to warn.
Light 5indicate the remote’s battery level:
· Fixed Red Light: No battery in the remote control.
· Flickering Red Light: Low battery of the remote
control.
Charging the Remote:
The lights will turn on from 5to 1. When all the
lights are fixed, this means that the remote control
has finished charging.
When the board is ON and the remote’s connec-
tion is working normally:
Lights 1& 2will be ON
Lights 3, 4& 5indicate the board’s battery
level.
Push forward
to Accelerate
Pull back
to Brake
Power Button,
Speed Selection or
Direction control
Throttle / Brake
Lights 1 & 2:
Speed mode 1
2
3
4
5
Lights 3, 4 & 5:
Skate and Remote
control battery
Micro USB
charging port
Light 5:
Remote control battery
ENGLISH8 |
remote control operation
Power ON/OFF:
Press the POWER BUTTON for 1 second to POWER ON the remote control.
Press the POWER BUTTON for 3 seconds to POWER OFF the remote control.
1. Make sure both the board and the remote are OFF.
2. Hold the remote near the skateboard.
3. Press and hold the power button on the remote and the pair button on the board at the same time for 3
seconds. Both buttons will start flashing quickly. Light 1, light 2or lights 1and 2will start flashing
on the remote, depending on the selected speed mode.
4. Press and hold both buttons until the remote control beeps thrice. Once you hear the beeps, the pairing
will be complete.
Once the pairing is finished, the connection will be automatic every time the board is ON.
The board might losethe connectionwith the remote, especiallyifyou are in a signal-polluted environment.
Try to pair it again if necessary. Radio frequency signals are absorbed or blocked by our bodies. Try to keep
the remote near the tail of the board, where the wireless signal receiver is built.
Try not to completely cover the remote with the hand; this can aect the wireless signal communication
between the remote and the board.
How to pair the remote control to the iWatSkate
| 9ENGLISH
remote control operation
Speed mode selection
There are three speed modes for the user to select. The first two LED indicate the speed:
ECO Mode Light 1
STREET Mode Light 2
PRO Mode Lights 1and 2
Selecting a speed mode
Set the throttle on a neutral position, and ride the board without accelerating.
Quickly press the power button TWICE to shift to the next speed mode (ECO/STREET/PRO).
How to switch the direction of the board
Make sure the board isn’t moving, and quickly press the power button ONCE to change the direction.
DO NOT under any circumstance, try to change the direction when the board is moving, it won’t work
and it’s extremely dangerous.
The power button won’t function as long as the board is moving. Please, don’t try to power the remote
OFF when the board is moving.
ECO Mode STREET Mode PRO Mode
ENGLISH10 |
remote control operation
Light 1and light 2:
In case of a signal loss between the remote and the board, light 1, light 2or lights 1and 2(depending
on which mode is selected) will start to flash and the board will automatically brake within 2 seconds, then
stop working if the connection cannot be resumed in time.
Please, be cautious if you observe a signal disconnection and try to avoid riding in heavily signal-interfered
areas.
When the board is OFF because the battery is exhausted or the board is defective, lights 1and 2will also
flash meaning the connection has been lost.
Light 3, light 4and light 5:
When lights 1and 2are ON, lights 3, 4and 5will indicate the battery of the board; when lights 1
and 2are flashing, light 5will indicate the battery of the remote.
If lights 3, 4and 5are ON, it means battery capacity is 75-100% full.
If lights 4and 5are ON, battery capacity is 25-75%.
Light 5is ON, battery capacity is below 25%.
Light 5is flashing, it means the board’s battery capacity is as low as 10% and the board’s speed will be
reduced. Charge the board immediately.
75-100% capacity
Below 25% capacity
25-75% capacity
Below 10% capacity
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Idiomas:
