Intersil ISL28208SOICEVAL2Z Manual de usuario
1
Application Note 1658
ISL28208SOICEVAL2Z Evaluation Board User’s Guide
Introduction
The ISL28208SOICEVAL2Z evaluation board is designed to
evaluate the performance of the ISL28208 dual Operational
Amplifier. The ISL28208 is a dual low power precision
amplifier that features a common mode input voltage range
extending to 0.5V below the V- rail, a rail-to-rail differential
input voltage range for use as a comparator, and rail-to-rail
output voltage swing, which makes it ideal for single supply
applications where input operation at ground is important.
With a wide operating range from 3V to 40V, in combination
with its precision, low power, and small footprint, ISL28208
provides the user with outstanding value and flexibility relative
to similar competitive parts.
Reference Documents
• ISL28208 Data Sheet, FN6935
Evaluation Board Key Features
• Single Supply Operation: +9V to +40V
• Dual Supply Operation: ±4.5V to ±20V
• Singled-Ended or Differential Input Operation
• External VREF input
• Banana Jack Connectors for Power Supply and VREF Inputs
• BNC Connectors for Op Amp Input and Output Terminals
• Convenient PCB Pads for Op Amp Input/Output Impedance
Loading
Power Supplies (Figure 1)
External power connections are made through the V+, V-, VREF,
and GND connections on the evaluation board. The circuit can
operate from a single supply or from dual supplies. For single
supply operation, the V- and GND pins are tied together to the
negative or ground reference of the power supply. For split
supplies, V+ and V- terminals connect to their respective
supply terminals. De-coupling capacitors C2 and C4 provide
low-frequency power-supply filtering, while additional
capacitors, C3 and C5, which are connected close to the part,
filter out high frequency noise. Anti-reverse diode D1 (optional)
protects the circuit in the momentary case of accidentally
reversing the power supplies to the evaluation board. The VREF
pin can be connected to ground to establish a ground
referenced input for split supply operation, or can be externally
set to any reference level for single supply operation.
FIGURE 1. POWER SUPPLY CIRCUIT
CLOSE TO DUT
2
0.01µF
0.01µF
2
1R31
1
R16
32
1
D1
C2 C4
C3 C5
3
2
1
J11
1
J14
1
J12
1
J13
3
2
1
J6
1
J8
0
0
1µF 1µF
VREF
V+
V-
FIGURE 2. PRECISION AMPLIFIER WITH G = -10V/V
INA-
INA+
R13/R23
ISL28208
+4.5V
V-
V+
10kΩ
10kΩ
-
+
100kΩ
VREF
100kΩ
VOUT
GAIN = -10V/V
TO +20V
PRECISION
SENSOR
-4.5V TO -20V
R11/R24
R14/R21
R18/R19
INB-
INB+
6
5
1/7
8
4
2
3
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
Copyright Intersil Americas Inc. 2011. All Rights Reserved.
1-888-INTERSIL or 1-888-468-3774 |Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.
July 26, 2011
AN1658.0
Application Note 1658
2AN1658.0
July 26, 2011
Amplifier Configuration (Figure 3)
The schematic of the op amp input stage with the components
supplied is shown in Figure 3, with a closed loop gain of 10V/V.
The differential amplifier gain is expressed in Equation 1:
For single-ended input with an inverting gain G = -10V/V, the IN+
input is grounded and the signal is supplied to the IN- input. VREF
can be connected to a reference voltage between the V+ and V-
supply rails. For non-inverting operation with G = 11V/V, the IN-
input is grounded and the signal is supplied to the IN+ input. The
non-inverting gain is strongly dependent on any resistance from
IN- to GND. For good gain accuracy, a 0Ωresistor should be
installed on the empty R5 pad.
User-selectable Options
(Figures 3 and 4)
Component pads are included to enable a variety of
user-selectable circuits to be added to the amplifier inputs, the
VREF input, outputs and the amplifier feedback loops.
A voltage divider (Figure 3, R18 and R15) can be added to
establish a power supply-tracking common mode reference
using the VREF input. The inverting and non-inverting inputs have
additional resistor placements for adding input attenuation, or to
establish input DC offsets through the VREF pin.
The output (Figure 4) also has additional resistor and capacitor
placements for filtering and loading.
NOTE: Operational amplifiers are sensitive to output capacitance
and may oscillate. In the event of oscillation, reduce output
capacitance by using shorter cables, or add a resistor in series
with the output.
VOUT VIN+
(VIN-)RF
(• RIN)⁄–VREF
+= (EQ. 1)
DNP
R5
R4
J2
J1 R1
R2
R14
R18R15
R13R11
10k
DNP
DNP
0
10k
DNP
100k
OPEN
100k
VREF
TO INA -
TO INA +
FROM VOUTA
C1
IN+A
IN-A
FIGURE 3. INPUT STAGE
OUT A
R26 J15
C8
R28
DNP
OPEN
0
OPEN
C6
VOUT_A
FIGURE 4. OUTPUT STAGE
TABLE 1. ISL28208SOICEVAL2Z COMPONENTS PARTS LIST
DEVICE # DESCRIPTION COMMENTS
C2, C4 CAP, SMD, 1206, 1µF, 50V, 10%, X7R, ROHS Power Supply Decoupling
C3, C5 CAP, SMD, 0603, 0.01µF, 50V, 10%, X7R, ROHS Power Supply Decoupling
C1, C6, C7, C8, C9, C10 CAP, SMD, 0603, DNP-PLACE HOLDER, ROHS User selectable capacitors - not populated
D1 40V DUAL SERIES SCHOTTKY BARRIER DIODE Reverse Power Protection
R11, R14, R21, R24 RESISTOR, SMD, 0603, 10kΩ, 1%, 1/16W, ROHS Gain Setting Resistor
R13, R23 RESISTOR, SMD, 0603, 100kΩ, 1%, 1/16W, ROHS Gain Setting Feedback Resistor
R1-R3, R5-R8, R10, R12, R15,
R17, R20, R22, R28-R30,
R32, R34-R36
RESISTOR, SMD, 0603, DNP-PLACE HOLDER, ROHS User selectable resistors - not populated
U1 (ISL28208FBZ) ISL28208FBZ, IC PRECISION LOW NOSIE JFET OP AMP, SOIC, ROHS
Application Note 1658
3
Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is
cautioned to verify that the Application Note or Technical Brief is current before proceeding.
For information regarding Intersil Corporation and its products, see www.intersil.com
AN1658.0
July 26, 2011
ISL28208SOICEVAL2Z Top View
Application Note 1658
4AN1658.0
July 26, 2011
ISL28208SOICEVAL2Z Schematic Diagram
OUT IN+ IN-IN+ NODE OUTIN- NODE
CLOSE TO DUT
2
2
1R29
R26
OPEN
0.01µF0.01µF
1R30 2
J21
1
21 R31
1R16
2
1
J23
2
1
J18
21
J24
2
J22
21
2
1
J20
2
1
J19
2
1
J17
21 R36
1R32 21 R34
2
1R35
32
1
D1
21
C1
21 R22
21 R19
21 R21
21 R20
21
C10
21 R8
21 R7
2
1R5
2
1R4 2
1R24
C2 C4
C3 C5
5
4
3
2
1J15
5
4
3
2
1J16
5
4
3
2
1
J2
5
4
3
2
1
J1
5
4
3
2
1
J3
5
4
3
2
1
J4
3
2
1
J11
1
J14
1
J12
1
J13
3
2
1
J6
1
J8
21
21 R27
21
C7
21
C6
21
C8
21
C9
21 R1
2
21 R25
21 R23
2
1R6
2
1R17
21 R2
21 R28
21 R14
21 R3
21 R18
21 R15
2
1R12
21 R10
2
1R13
21 R11
8
7
6
54
3
2
1
U1
10k
100k
0
0
SOIC8
DNP
0
DNP
OPEN
DNP
OPEN
OPEN
0
DNP
DNP
DNP
DNP
OPEN
DNP
DNP
DNP
DNP
DNP
DNP
DNP
DNP
DNP
DNP
OPEN
DNP
DNP
10k 100k
100k
10k
10k
0
0 DNP
100k
1µF 1µF
VREF
VREF
V+V-
5
6
7
8
3
4
1
2GENERIC
PACK.
OUT A
OUT B
IN-A
IN+A
IN-B
IN+B
Tabla de contenidos
Otros manuales de Placa madre de Intersil
Intersil
Intersil ISL32741EVAL1Z Manual de usuario
Intersil
Intersil ISL2827xINEVAL1Z Manual de usuario
Intersil
Intersil ISL71010BM25EV1Z Manual de usuario
Intersil
Intersil ISL97519IUZ-EVALZ Instrucciones de uso
Intersil
Intersil ISL9220IRTZEVAL1Z Instrucciones de instalación y funcionamiento
Intersil
Intersil ISL281X7MSOPEVAL1Z Manual de usuario
Intersil
Intersil ISL32740EVAL2Z Manual de usuario
Intersil
Intersil ISL73847SEHEV2Z Manual de usuario
Intersil
Intersil ZL2005P Manual de usuario
Intersil
Intersil ISL9214AEVAL1Z Instrucciones de uso
Intersil
Intersil ISL76683 Manual de usuario
Intersil
Intersil ISL62883EVAL2Z Manual de usuario
Intersil
Intersil ISL1208 Instrucciones de instalación y funcionamiento
Intersil
Intersil ISL6442 Manual de usuario
Intersil
Intersil ISL75052SEHEVAL1Z Manual de usuario
Intersil
Intersil ISL8014AEVAL2Z Instrucciones de instalación y funcionamiento
Intersil
Intersil ISL6294AEVAL1Z Instrucciones de uso
Intersil
Intersil ISL45042EVAL1Z Manual de usuario
Intersil
Intersil ISL6296 Instrucciones de instalación y funcionamiento
Intersil
Intersil ISL9120IIx-EVZ Manual de usuario
Manuales populares de Placa madre de otras marcas
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manual de usuario
Gigabyte
Gigabyte GA-9IVDT Manual de usuario
Texas Instruments
Texas Instruments ADS8372EVM Manual de usuario
Commell
Commell MS-C73 Manual de usuario
IBT Technologies
IBT Technologies MB860 Manual de usuario
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manual de usuario
