Impex MWB 715B Manual de usuario

NOTE:

Please read all instructions

carefully before using this

product

Safety Notice

Hardware Identifier

Assembly Instruction

Parts List

Warranty

Ordering Parts

Model

MWB 715B

Retain This

Manual for

Reference

08-20-03

OWNER'S

MANUAL

MARCY WEIGHT BENCH

MWB 715B

IMPEX FITNESS PRODUCTS

14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746

Tel: (800) 999-8899 Fax: (626) 961-9966

www.impex-fitness.com

[email protected]

TABLE OF CONTENTS

BEFORE YOU BEGIN...................................................................................... 1

IMPORTANT SAFETY NOTICES..................................................................... 2

HARDWARE IDENTIFIER.....…....................................................................... 3

ASSEMBLY INSTRUCTIONS........................................................................... 4

EXPLODED DIAGRAM……………………………………………………………... 8

PARTS LIST……………………………………………………………………….. 9

WARRANTY.................................................................................................… 10

ORDERING PARTS......................................................................................... 10

BEFORE YOU BEGIN

Thank you for selecting the MARCY WEIGHT BENCH 715B by IMPEX

FITNESS PRODUCTS. For your safety and benefit, read this manual carefully

before using the machine. As a manufacturer, we are committed to provide

you complete customer satisfaction. If you have any questions, or find there

are missing or damaged parts, we guarantee you complete satisfaction through

direct assistance from our factory. To avoid unnecessary delays, please call

our TOLL-FREE customer service number. Our Customer Service Agents will

provide immediate assistance to you.

Toll-Free Customer Service Number

1-800-999-8899

Mon. - Fri. 9 a.m. - 5 p.m. PST

www.impex-fitness.com

[email protected]m

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply

whenever you operate a piece of exercise equipment. Be sure to read the entire manual

before you assemble or operate your machine. In particular, note the following safety

precautions:

1. Keep children and pets away from the machine at all times. DO NOT

leave children unattended in the same room with the machine.

2. Only one person at a time should use the machine.

3. If the user experiences dizziness, nausea, chest pain, or any other abnormal

symptoms, STOP the workout at once. CONSULT A PHYSICIAN

IMMEDIATELY.

4. Position the machine on a clear, leveled surface. DO NOT use the machine

near water or outdoors.

5. Keep hands away from all moving parts.

6. Always wear appropriate workout clothing when exercising. DO NOT wear

robes or other clothing that could become caught in the machine. Running

or aerobic shoes are also required when using the machine.

7. Use the machine only for its intended use as described in this manual. DO

NOT use attachments not recommended by the manufacturer.

8. Do not place any sharp object around the machine.

9. Disabled person should not use the machine without a qualified person or

physician in attendance.

10. Before using the machine to exercise, always do stretching exercises to

properly warm up.

11. Never operate the machine if the machine is not functioning properly.

12. A spotter is recommended during exercise.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR

PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF

35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL

INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES

NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED

BY OR THROUGH THE USE OF THIS PRODUCT.

SAVE THESE INSTRUCTIONS.

ASSEMBLY INSTRUCTION

Tools Required to Assemble the Machine: Two Adjustable Wrenches and Allen Wrenches.

NOTE: It is strongly recommended this machine to be assembled by two or more people to

avoid possible injury.

STEP 1 (See Diagram 1)

A.) Connect the Rear Upright Beams (#1) by a Cross Brace (#5) in the mid-span. Align the holes

and secure them with one Triangle Bracket (#12), one Bent Bracket (#13), two M10 x 3 ½”

Carriage Bolts (#34), two M10 x 2 3/8” Carriage Bolts (#36), four ∅¾” Washers (#43), and

four M10 Aircraft Nuts (#42) on each end of the Cross Brace.

B.) Attach the Front Stabilizer (#2) to the front of the Main Seat Support (#3). Secure it with one

M10 x 2 ½” Carriage Bolt (#51), two M10 x 2 ¾” Carriage Bolts (#35), ∅¾” Washers (#43),

and M10 Aircraft Nuts (#42).

C.) Attach the back of the Main Seat Support (#3) to the Cross Brace (#5). Secure it with one

Bracket (#14), two M10 x 2 3/8” Carriage Bolts (#36), ∅¾” Washers (#43), and M10 Aircraft

Nuts (#42).

D.) Insert two Crutches (#7) into the top openings on the Upright Beams. Secure them with two

Lock Knobs (#33) through selected holes to obtain desired height of the Supports.

E.) Place Backrest Adjustment Bar (#8) between the two Upright Beams on the selected bar

holder to obtain desired incline of Backrest.

DIAGRAM 1

STEP 2 (See Diagram 2)

A.) Attach the Seat Bracket (#4) to the short pivot tube on the Main Seat Support (#3).

Secure it with one M10 x 4 ¾” Allen Bolt (#39) and M10 Aircraft Nut (#42). Place the

Seat Pad (#16) onto the Seat Bracket (#4). Secure it with four M6 x 5/8” Philips Head

Screws (#38) and ∅½” Washers (#44). Insert a L-shaped Pin (#31) into the selected

hole on the Seat Bracket to obtain the desired incline of the Seat.

B.) Attach the side-holes of Backrest Supports (#6) to the long pivot tube on the Main Seat

Support (#3). Secure it with one M10 x 7 ¼” Hex Bolt (#50), two ∅¾” Washers (#43),

and one M10 Aircraft Nut (#42). Place the Backrest Board (#17) onto the Backrest

Supports (#6). Secure it with four M6 x 1 3/8” Philips Head Screws (#37) and ∅½”

Washers (#44).

DIAGRAM 2

STEP 3 (See Diagram 3)

A.) Insert the Leg Developer Holder (#9) into the top opening on the Front Stabilizer (#2).

Secure it with a Lock Knob (#33).

B.) Attach the Leg Developer (#10) to the bracket on the Leg Developer Holder (#9). Secure

it with an Axle (#18), two ∅¾” Washers (#43), and two M10 x 5/8” Allen Bolts (#40).

Insert one Foam Roll Tube (#11) halfway through the hole on the Leg Developer Holder

(#9). Insert two Foam Roll Tubes (#11) halfway through the holes on the Leg Developer

(#10). Push six Foam Rolls (#27) onto the Tubes from both sides. Plug six Foam Roll

End Caps (#26) into the ends.

C.)Slide the Olympic Sleeve (#15) onto the weight post on the Leg Developer (#10). Attach

a Spring Clip (#32) onto the Olympic Sleeve. NOTE: When using the decline position to

do Ab exercise, place at least 30lbs of weights on the post to hold down the Leg

Developer.

DIAGRAM 3

STEP 4 (See Diagram 4)

A.) Attach the Arm Curl Pad (#47) to the Arm Curl Stand (#48). Secure it with two M8 x

5/8” Allen Bolts (#46) and ∅5/8” Washers (#45).

B.) For Arm Curl exercise, remove Leg Developer and insert the Arm Curl Stand into the

opening on top of Front Stabilizer. Secure it with a Lock Knob (#33) to the selected hole

to obtain the desired height.

DIAGRAM 4

PARTS LIST

KEY NO. DESCRIPTION Q’ty

1 Rear Upright Beam 2

2 Front Stabilizer 1

3 Main Seat Support 1

4 Seat Bracket 2

5 Cross Brace 2

6 Backrest Support 2

7 Crutch 2

8 Backrest Adjustment Bar 1

9 Leg Developer Holder 1

10 Leg Developer 1

11 Foam Roll Tube 3

12 Triangle Bracket 2

13 Bent Bracket 2

14 Bracket 1

15 Olympic Sleeve 1

16 Seat Pad 1

17 Backrest Board 1

18 Axle 1

19 Leg Developer Bushing 2

20 2 3/8” End Cap 2

21 1 ¾” Square End Cap 1

22 1” Square End Cap 2

23 ∅1” End Cap 1

24 ∅1 1/8” End Cap 2

25 ∅1” Cone-shaped Cap 1

26 Foam Roll End Cap 6

27 Foam Roll 6

28 2” Leg Developer Holder Sleeve 1

29 Inner Cap 2

30 3” Sleeve 2

31 L-shaped Pin 1

32 Spring Clip 1

33 Lock Knob 3

34 M10 x 3 ½” Carriage Bolt 4

35 M10 x 2 ¾” Carriage Bolt 2

36 M10 x 2 3/8” Carriage Bolt 6

37 M6 x 1 3/8” Philips Head Screw 4

38 M6 x 5/8” Philips Head Screw 4

39 M10 x 4 ¾” Allen Bolt 1

40 M10 x 5/8” Allen Bolt 2

41 3/8” Philips Head Screw 4

42 M10 Aircraft Nut 14

43 ∅¾” Washer 16

44 ∅½” Washer 8

45 ∅5/8” Washer 2

46 M8 x 5/8” Allen Bolt 2

47 Arm Curl Pad 1

48 Arm Curl Stand 1

49 Bushing 2

50 M10 x 7 ¼” Hex Bolt 1

51 M10 x 2 ½” Carriage Bolt 1

Otros manuales para MWB 715B

Tabla de contenidos

Otros manuales de Gimnasio en casa de Impex

Impex

Impex MARCY MWB-544 Manual de usuario

Impex

Impex MARCY DIAMOND ELITE MD-389 Manual de usuario

Impex

Impex Marcy MCB-999 Manual de usuario

Impex

Impex MARCY MCB-347 Manual de usuario

Impex

Impex MARCY MKB-733 Manual de usuario

Impex

Impex Marcy SB-685 Manual de usuario

Impex

Impex MARCY CLASSIC MCB-252 Manual de usuario

Impex

Impex MARCY PRO SM-4903 Manual de usuario

Impex

Impex MARCY MWB-345 Manual de usuario

Impex

Impex MARCY DIAMOND ELITE MD-9010G Manual de usuario

Impex

Impex GD-810 Manual de usuario

Impex

Impex POWERHOUSE WM-1501 Manual de usuario

Impex

Impex IRON GRIP STRENGTH TSA-88 Manual de usuario

Impex

Impex MARCY MWM 1801 Manual de usuario

Impex

Impex MARCY PRO PM-2084 Instrucciones de instalación y funcionamiento

Impex

Impex MARCY DIAMOND ELITE MD-3401 Manual de usuario

Impex

Impex MARCY CR 5 Manual de usuario

Impex

Impex Marcy Diamond MD-8861 Manual de usuario

Impex

Impex IGS-411 Manual de usuario

Impex

Impex MARCY MWM-7150 Manual de usuario

Impex

Impex POWERHOUSE WM-1501 Manual de usuario

Impex

Impex POWERHOUSE ELITE PHE1000 Manual de usuario

Impex

Impex IVANKO IVK-2155 Manual de usuario

Impex

Impex Marcy Platinum GS 99 Manual de usuario

Manuales populares de Gimnasio en casa de otras marcas

Horizon Fitness

Horizon Fitness OXFORD 6 Manual de usuario

Energetics

Energetics Multi Trainer 5.1 Manual de usuario

Matrix

Matrix MG-PL Series Manual de usuario

Reebok

Reebok Tbr2i Manual de operación y mantenimiento

Weider

Weider 8300 Hard Drive Manual de usuario

Pure Fitness

Pure Fitness 8526HE Manual de usuario

Weider

Weider 8700 I Guía de inicio rápido

Bowflex

Bowflex Sport 001-6961 Manual de usuario

NordicTrack

NordicTrack E8200 Competition Bench Guía de inicio rápido

Weider

Weider WEMC10161 Manual de usuario

Body Solid

Body Solid GHYP-345 Manual de usuario

Evo

Evo TAHOE 5105 Manual de usuario

cardiobull

cardiobull RA17 Manual de usuario

ParaBody

ParaBody 40 Manual de usuario

JLL

JLL Ventus Pro Air Power Manual de usuario

Trojan

Trojan Colorado 370 Manual de usuario

Octane Fitness

Octane Fitness xRide xR650 Manual de usuario

Precor

Precor Discovery Series Manual de usuario