Impex MARCY CR 5 Manual de usuario

MARCY CORNER GYM

CR 5N

IMPEX FITNESS PRODUCTS

14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746

Tel: (800) 999-8899 Fax: (626) 961-9966

www.impex-fitness.com

[email protected]

NOTE:

Please read all instructions

carefully before using this

product

Table of Contents

Safety Notice

Hardware Identifier

Assembly Instruction

Parts List

Resistance Chart

Warranty

Ordering Parts

Model

MWM CR5N

Retain This

Manual for

Reference

07-24-03

OWNER'S

MANUAL

TABLE OF CONTENTS

BEFORE YOU BEGIN...................................................................................... 1

IMPORTANT SAFETY NOTICES..................................................................... 2

HARDWARE IDENTIFIER.....…....................................................................... 3

ASSEMBLY INSTRUCTIONS...............................................................…..........4

PARTS LIST…………………………………………………………….……….…….23

RESISTANCE CHART……………………………………………………………….24

WARRANTY.................................................................................................… 25

ORDERING PARTS......................................................................................... 25

BEFORE YOU BEGIN

Thank you for selecting the MARCY CR5N CORNER GYM by IMPEX FITNESS

PRODUCTS. For your safety and benefit, read this manual carefully before

using the machine. As a manufacturer, we are committed to provide you

complete customer satisfaction. If you have any questions, or find there are

missing or damaged parts, we guarantee you complete satisfaction through

direct assistance from our factory. To avoid unnecessary delays, please call our

TOLL-FREE customer service number. Our Customer Service Agents will

provide immediate assistance to you.

Toll-Free Customer Service Number

1-800-999-8899

Mon. – Fri. 9 a.m. – 5 p.m. PST

www.impex-fitness.com

[email protected]m

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply whenever

you operate a piece of exercise equipment. Be sure to read the entire manual before you

assemble or operate your machine. In particular, note the following safety precautions:

1. Keep children and pets away from the machine at all times. DO NOT

leave children unattended in the same room with the machine.

2. Only one person at a time should use the machine.

3. If the user experiences dizziness, nausea, chest pain, or any other abnormal

symptoms, STOP the workout at once. CONSULT A PHYSICIAN

IMMEDIATELY.

4. Position the machine on a clear, leveled surface. DO NOT use the machine

near water or outdoors.

5. Keep hands away from all moving parts.

6. Always wear appropriate workout clothing when exercising. DO NOT wear

robes or other clothing that could become caught in the machine. Running

or aerobic shoes are also required when using the machine.

7. Use the machine only for its intended use as described in this manual. DO

NOT use attachments not recommended by the manufacturer.

8. Do not place any sharp object around the machine.

9. Disabled person should not use the machine without a qualified person or

physician in attendance.

10. Before using the machine to exercise, always do stretching exercises to

properly warm up.

11. Never operate the machine if the machine is not functioning properly.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN.

THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS

WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING

ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL

INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS

PRODUCT.

SAVE THESE INSTRUCTIONS.

ASSEMBLY INSTRUCTION

Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches

NOTE: It is strongly recommended two or people assembling this machine to avoid

possible injury.

STEP 1 (See Diagram 1)

A.) Place the Right Base Frame (#46) and Left Base Frame (#87) on the floor, at a right angle to

each other. Attach the Rear Vertical Beam (#50) to the joint and align the holes. Secure the

holes with two M10 x 3” Carriage Bolts (#64), ∅3/4” Washers (#6) and M10 Aircraft Nuts (#5).

DO NOT tighten all the nuts and bolts yet.

Diagram 1

STEP 2 (See Diagram 2)

A.) Attach the Right Vertical Beam (#21) to the Right Base Frame (#46). Secure it with two M10 x

2 ¾” Carriage Bolts (#17), ∅¾” Washers (#6), and M10 Aircraft Nuts (#5).

B.) Attach the Right Seat Support (#49) to the Right Vertical Beam (#21). Secure it with one

Bracket (#7), two M10 x 2 ¾” Carriage Bolts (#17), ∅¾” Washers (#6), and M10 Aircraft Nuts

(#5).

C.)Attach the other end of Right Seat Support (#49) to the Right Base Frame (#46). Secure it with

one M10 x 2 ½” Carriage Bolt (#100), ∅¾” Washer (#6), and M10 Aircraft Nut (#5).

D.)Attach the Leg Developer (#40) to the front open bracket on the Right Seat Support. Secure it

with a Leg Developer Axle (#41), two ∅¾” Washers (#6), and M10 x ¾” Allen Bolts (#37).

DIAGRAM 2

STEP 3 (See Diagram 3)

A.) Slide two ∅2 ½” Rubber Bumpers (#58) onto two Chromed Guide Rods (#58). Insert the two

Guide Rods into the holes on the Right Base Frame (#46). Slide the Selector Stem (#67) onto

the two Guide Rods (#22). Slide the Selector Stem over the Selector Rod (#69). Secure the

Selector Rod to the Selector Stem with two M10 x 1” Allen Bolts (#56). DO NOT install the

plates yet.

B.) Repeat the Procedure A above to install another set of Guide Rods.

C.)Place the Upper Frame (#8) over the two sets of Guide Rods then onto top of Right Vertical

Beam (#21) and Rear Vertical Beam (#50).

D.)Secure each set of Guide Rods (#22) to the Upper Frame with two M10 x 1” Allen Bolts (#56)

and ∅¾” Washers (#6).

E.) Secure the Right Vertical Beam (#21) to the Upper Frame with one Bracket (#7), two M10 x 2

¾” Carriage Bolts (#17), ∅¾” Washers (#6), and M10 Aircraft Nuts (#5).

F.) Attach top of Left Vertical Beam (#77) to the Upper Frame. Attach the bottom of Left Vertical

Beam to the Left Base Frame (#87). Secure the bottom of Left Vertical Beam with two M10 x 2

¾” Carriage Bolts (#17), ∅¾” Washers (#6), and M10 Aircraft Nuts (#5).

G.)Secure the Left Vertical Beam (#77), Rear Vertical Beam (#50), and Upper Frame (#8) all

together with two M10 x 3” Carriage Bolts (#64), ∅¾” Washers (#6), and M10 Aircraft Nuts

(#5).

H.)Attach the Left Seat Support (#92) to the Left Vertical Beam (#77). Secure it with one Bracket

(#7), two M10 x 2 ¾” Carriage Bolts (#17), ∅¾” Washers (#6), and M10 Aircraft Nuts (#5).

Attach the other end of Left Seat Support (#92) to the Left Base Frame (#87). Secure it with

one M10 x 2 ½” Carriage Bolt (#100), ∅¾” Washer (#6), and M10 Aircraft Nut (#5).

I.) Securely tighten all nuts and bolts previously installed.

J.) Carefully tilt the machine on its side. (Help of another person is a MUST.) Secure the four

Guide Rods (#22) to the Right Base Frame (#46) with four M10 x 1” Allen Bolts (#56).

K.) Attach the bottom of Leg Press Frame (#84) to the bracket on the Left Base Frame (#87).

Secure it with a M12 x 3” Allen Bolt (#89), two ∅7/8” Washers (#71), and one M12 Aircraft Nut

(#57).

L.) Attach a Leg Press Diagonal Support (#90) to each side of the Leg Press Frame. Secure them

together with two M10 x 2 ½” Allen Bolts (#10), four ∅¾” Washers (#6), and two M10 Aircraft

Nuts (#5).

DIAGRAM 3

STEP 4 (See Diagram 4)

A.) Attach the Front Press Base (#97) to the Right Base Frame (#46). Secure it with a 9 ¼” Front

Press Axle (#60), two ∅¾” Washers (#6), and two M10 Aircraft Nuts (#5).

B.) Attach the Front Press Frames (#63) to the Front Press Base. Secure it with four M10 x 2 ¾”

Carriage Bolts (#17), ∅¾” Washers (#6), and M10 Aircraft Nuts (#5).

DIAGRAM 4

STEP 5 (See Diagram 5)

A.) Attach the Butterfly Support Frame (#18) to the front of Right Vertical Beam (#21). Attach the

Butter Pulley Support (#74) to the back of Right Vertical Beam. Align the holes. Secure them

together with two M10 x 2 ¾” Carriage Bolts (#17), ∅¾” Washers (#6), and M10 Aircraft Nuts

(#5).

B.) Insert the Axle on the Left Butterfly (#20) into the hole on the Butterfly Support Frame from the

bottom. Secure it with one ∅1 ½” Washer (#16), ∅1 1/2” Lock Ring (#13), M6 x 1 3/8” Hex

Socket Bolt (#12), and M6 Aircraft Nut (#14). Repeat the same procedure to install the other

side.

C.)Slide two Butterfly Foam Rolls (#27) onto the Butterfly Arms.

D.)Attach a Swivel Pulley Bracket (#72) to the bottom of the Butterfly Pulley Support (#74).

Secure it with a M12 x 4 ½” Allen Bolt (#70), two 7/8” Washers (#71), and one M12 Aircraft Nut

(#57). Repeat for the other side.

DIAGRAM 5

Otros manuales para MARCY CR 5

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Gimnasio en casa de Impex

Impex

Impex MACH IV Manual de usuario

Impex

Impex MFB 400 Manual de usuario

Impex

Impex MARCY MWM-980 Manual de usuario

Impex

Impex Iron Grip Strength IGS-412 Manual de usuario

Impex

Impex MARCY MWB 850 Manual de usuario

Impex

Impex POWERHOUSE CLUB PWR 6 Manual de usuario

Impex

Impex POWERHOUSE SB 680 Manual de usuario

Impex

Impex Marcy MWB-4360 Manual de usuario

Impex

Impex MARCY MWM-1860 Manual de usuario

Impex

Impex SteelBody STB-98501 Manual de usuario

Impex

Impex PHC -265 Manual de usuario

Impex

Impex Iron Grip Strength IGS-2110 Manual de usuario

Impex

Impex MARCY MWM-1509 Manual de usuario

Impex

Impex SB 661 Manual de usuario

Impex

Impex IVANKO IVK-2155 Manual de usuario

Impex

Impex MARCY PRO 5 Manual de usuario

Impex

Impex Iron Grip Sport IGS-10 Manual de usuario

Impex

Impex MARCY MWM-8900 Manual de usuario

Impex

Impex MARCY MULTI PURPOSE BENCH MWB-682 Manual de usuario

Impex

Impex TSA-42 Manual de usuario

Impex

Impex Marcy Platinum GS 99 Manual de usuario

Impex

Impex COMPETITOR CB-430 Manual de usuario

Impex

Impex MARCY SM-5092 Manual de usuario

Impex

Impex MARCY DIAMOND ELITE MD-857 Manual de usuario

Manuales populares de Gimnasio en casa de otras marcas

Horizon Fitness

Horizon Fitness OXFORD 6 Manual de usuario

Energetics

Energetics Multi Trainer 5.1 Manual de usuario

Matrix

Matrix MG-PL Series Manual de usuario

Reebok

Reebok Tbr2i Manual de operación y mantenimiento

Weider

Weider 8300 Hard Drive Manual de usuario

Pure Fitness

Pure Fitness 8526HE Manual de usuario

Weider

Weider 8700 I Guía de inicio rápido

Bowflex

Bowflex Sport 001-6961 Manual de usuario

NordicTrack

NordicTrack E8200 Competition Bench Guía de inicio rápido

Weider

Weider WEMC10161 Manual de usuario

Body Solid

Body Solid GHYP-345 Manual de usuario

Evo

Evo TAHOE 5105 Manual de usuario

cardiobull

cardiobull RA17 Manual de usuario

ParaBody

ParaBody 40 Manual de usuario

JLL

JLL Ventus Pro Air Power Manual de usuario

Trojan

Trojan Colorado 370 Manual de usuario

Octane Fitness

Octane Fitness xRide xR650 Manual de usuario

Precor

Precor Discovery Series Manual de usuario