IFM O1D100 series Manual de usuario
Mode/
Enter Set
PWR mm m inch OUT1 OUT2
Output LED’s
Setting of the parameters
Mode: Selecting the mode
Enter: Acknowledging the setting
4 digit numeric display
Programming Mode
Press until desired menu item is
displayed. (See distance
sensor menu items)
Press to display the current setting.
To change the setting, press and hold the set button
for 5 seconds until the flashing value is continuously
incremented. After this time, the value may be increased
continuously (by holding down the set button) or incre-
mented (by pressing and releasing the button repeatedly)
until the desired value is reached.
Press once to enter desired value.
The desired value is set. If no button is pressed for 15
seconds, the sensor returns to the operating mode.
Repeat these steps to set other values as required.
1
2
3
4
5
6
Display
O1D100 Series
Distance Sensor
Display Unit LED’s
Setpoint 1
Output 1
Hysteresis mode: normally open
Hysteresis mode: normally closed
Output 2
Hysteresis mode: normally open
Hysteresis mode: normally closed
4 - 20 mA analog output
Analog start point
Analog end point
Setpoint 2
Sampling rate
Repeatability
Program (Display units) first to avoid
programming errors.
Distance Sensor Menu Items
(continued)
Enhanced functions - Press Set, then Mode/ Enter
button to scroll through the Enhanced Function
options.
On delay for switching output
Off delay for switching output
Display options
Display updated every 50 mS
Display updated every 200 mS
Display updated every 600 mS
Same as above with
display rotated 180º
Display deactivated
Indication of signal strength in %
Select display units (m, mm, inch)
Millimeter
Meter
Inch
Return to factory default
Software revision
TEL: 800-441-8246 • FAX: 800-329-0436
www.ifmefector.com
10/05
Lit. No. B41005
Measuring
range
[mm]
Repeatability* [mm] Accuracy* [mm]
white (90%
remission)
grey (18%
remission)
white (90%
remission)
grey (18%
remission)
200...1000 10 (±5) 15 (±7.5) ±15 ±18
1000...2000 11 (±5.5) 20 (±10) ±15 ±20
2000...4000 35 (±17.5) 45 (±22.5) ±25 ±32
4000...6000 55 (±27.5) 80 (±40) ±35 ±50
6000...10,000 120 (±60) –±70–
* The values specified for repeatability and accuracy refer to a sampling
frequency of 50 Hz. At a lower sampling frequency, which is adjustable
on the unit, these values will be lower. View the calculation tool at
www.ifmefector.com/ifmus/web/pmd_5.htm
Distance to target
(shown on sensor display)
[mm]
200...1000
1,000...2000
2,000...4000
4,000...6000
6,000...10,000
Minimum distance from
target to background
[mm]
38
50
113
200
300
For background suppression applications
The following chart shows the minimum distance required
between target and background
Tabla de contenidos
Otros manuales de Accesorios de IFM
IFM
IFM JN2101 Manual de usuario
IFM
IFM GI854S Manual de usuario
IFM
IFM LDH100 Manual de usuario
IFM
IFM O5D10 Series Manual de usuario
IFM
IFM PQ3 Series Manual de usuario
IFM
IFM Ecomat 100 EC2082 Guía
IFM
IFM efector200 OM Manual de usuario
IFM
IFM O2D54 Series Manual de usuario
IFM
IFM EIO104 Manual de usuario
IFM
IFM LR3009 Manual de usuario
IFM
IFM O5E5 Series Manual de usuario
IFM
IFM O5E7 Series Manual de usuario
IFM
IFM PI28 Series Manual de usuario
IFM
IFM O3M150 Instrucciones de montaje
IFM
IFM SBY2 Series Manual de usuario
IFM
IFM PM16 Series Manual de usuario
IFM
IFM DTI424 Manual de usuario
IFM
IFM Efector 200 OM Manual de usuario
IFM
IFM SBT633 Manual de usuario
IFM
IFM PC3 Series Manual de usuario
