IFM Efector 200 O5PG Manual de usuario

Operating instructions

Retro-reflective sensor

O5PG

704156 / 00 08 / 2007

Contents

Functions and features�� 3

Installation �� 3

Operating and display elements�� 3

Electrical connection�� 4

Set-up�� 4

Sensitivity setting (1-point teach)�� 5

a) Output switched ON when object detected �� 5

Sensitivity setting unsuccessful:�� 5

b) Output switched OFF when object detected �� 5

Sensitivity setting (2-point teach)�� 6

a) Output switched ON when object detected �� 6

Sensitivity setting unsuccessful:�� 6

b) Output switched OFF when object detected �� 6

Electronic lock �� 7

Operation�� 7

Switch point compensation�� 7

Maintenance�� 7

Functions and features

In conjunction with a prismatic reflector or reflective tape the retro-reflective sen-

sor detects transparent objects and materials without contact and indicates their

presence by a switched signal�

Range (r): see type label

(Value refers to prismatic reflector 50 x 50 mm, E20722)�

Installation

Operating and

display elements

1: LEDs

2: OUTon pushbutton

3: OUTo󰀨 pushbutton

Fit the prismatic reflector or the reflective tape behind the target object�

Align the retro-reflective sensor to the reflector or tape and fix it by means of a

mounting fixture� When selecting the prismatic reflector ensure that the surface

area is greater than the light spot�

Maximum range only with accurate alignment�

Optimum excess gain is reached if the excess gain graph on the ifm homepage is

adhered to:

→ “Data sheet direct” > “Additional data”

Electrical connection

Disconnect the power supply� Connect the unit�

































1: L+

2: function check output

3: L-

4: switching output

5: not connected

On power up, the unit recognises automatically if the switching output is con-

nected to L- (= PNP) or to L+ (= NPN)� The polarity of the function check output is

set according to the polarity of the switching output�

Both outputs must be connected with the same polarity:

PNP or NPN!

Set-up

The retro-reflective sensor is set to min� sensitivity and must necessarily be set to

the original application using one of the methods described below (1-point teach

or 2-point teach)� Otherwise the factory setting will not result in an output function�

Sensitivity setting (1-point teach)

Useful if the object is highly transparent or with thin film� However, excess gain is

less than using the 2-point teach�

a) Output switched ON when object detected

►Remove object

►Press [OUToff] for 2 s�

>Yellow LED flashes

►Release pushbutton

>Sensitivity measurement carried out (1 s)

>Yellow LED flash rate doubles

►Press and release [OUToff]

>Sensitivity measurement carried out (1 s)

>Yellow LED out� Programming complete�

Sensitivity setting unsuccessful:

>The yellow LED flashes fast, 8Hz� Cause:

• Signal from prismatic reflector unstable (e�g� in case of vibration)

• Max� setting time 15 min� exceeded

>Unit ignores setting attempt

b) Output switched OFF when object detected

Proceed as above, but:

►Each time press [OUTon]�

>Yellow LED on�

Sensitivity setting (2-point teach)

Useful when the object has high contrast as compared to the reflector or light and

dark objects need to be differentiated� This results in a higher excess gain�

a) Output switched ON when object detected

►Position object

►Press [OUTon] for 2 s

>Yellow LED flashes

►Release button

>Sensitivity measurement carried out (1 s)

>Yellow LED flash rate doubles

►Remove object

►Press and release [OUToff]

>Sensitivity measurement carried out (1 s)

>Yellow LED out� Programming complete�

Sensitivity setting unsuccessful:

>The yellow LED flashes fast, 8 Hz� Cause:

• Insufficient difference in measurements

• Max� setting time 15 min� exceeded

>Unit ignores setting attempt

b) Output switched OFF when object detected

Proceed as above, but:

►In step 1 press [OUToff]�

►In step 2 press [OUTon]�

>Yellow LED on�

Electronic lock

►To lock press [OUTon] and [OUToff] together for 10��20 s�

>Acknowledgement: LED status (yellow) inverted�

►To unlock repeat procedure�

Operation

Check whether the unit operates correctly� Display by LEDs�

Yellow LED on OUT output is switched

Red LED on

Limit of the switch point compensation reached:

e�g� unit out of alignment; lens / reflector dirty

FC output switched

Yellow LED flashes

2 Hz: internal fault�

8 Hz: sensitivity setting incorrect�

(OUT output is not switched)�

Switch point compensation

The O5G501 unit has no switch point compensation�

Once the sensitivity setting has been carried out, the unit automatically compen-

sates for switch point drift�

The red LED lights and the output FC “Function check output” switches as soon

as the limit of the switch point compensation is reached� At this point the lens of

the unit and the prismatic reflector need to be cleaned (→ Maintenance).

After cleaning new programming of the unit is carried out automatically� To do so,

no object is allowed in the beam�

Maintenance

Keep the lens of the unit and the prismatic reflector free from contamination� For

cleaning do not use any solvents or cleaning agents which could damage the

plastic�

Tabla de contenidos

Otros manuales de Accesorios de IFM

IFM

IFM PI16 Series Manual de usuario

IFM

IFM OJ Manual de uso y cuidado

IFM

IFM OF Series Manual de usuario

IFM

IFM O6H7 Series Manual de usuario

IFM

IFM KI0054 Manual de usuario

IFM

IFM O1D120 Manual de usuario

IFM

IFM SAxx04 Series Manual de usuario

IFM

IFM UGT58 Series Manual de usuario

IFM

IFM PN01 A Series Manual de usuario

IFM

IFM LT80 Series Manual de usuario

IFM

IFM O3D3 Series Manual de usuario

IFM

IFM PK752 Series Manual de usuario

IFM

IFM efector 150 KF Manual de usuario

IFM

IFM Ecomat 100 EC2082 Guía

IFM

IFM Efector 200 OGH2 Series Manual de usuario

IFM

IFM OJ51 Series Manual de usuario

IFM

IFM O5H5xA Series Manual de usuario

IFM

IFM Efector 200 O6E4 Manual de usuario

IFM

IFM SBG2 Series Manual de usuario

IFM

IFM Efector 160 LR70 Manual de usuario

IFM

IFM efector 200 OGH Manual de usuario

IFM

IFM PC3 Series Manual de usuario

IFM

IFM O2D50 Series Manual de usuario

IFM

IFM PN78 Series Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario