IFM O6H7 Series Manual de usuario

Operating instructions

Diffuse reflection sensor with

background suppression

O6H7xx

706457 / 00 11 / 2017

Contents

1 Preliminary note��3

1�1 Symbols used ��3

2 Safety instructions ��3

3 Functions and features ��3

4 Installation��4

5 Operating and display elements ��5

5�1 Stability indication��5

6 Electrical connection��6

6�1 PNP ��6

6�2 NPN ��6

7 Settings��7

7�1 Settings on the sensor��7

7�1�1 The sensor is to switch when the object is detected ��7

7�1�2 The sensor is not to switch when the object is detected ��7

7�1�3 Set maximum range ��7

7�1�4 Programming unsuccessful ��8

7�1�5 Electronic lock ��8

7�2 Setting via IO-Link ��9

7�2�1 Adjustable parameters��9

7�2�2 Setting the range by means of background and object �� 11

7�2�3 Setting the range by means of background��12

7�2�4 Setting the maximum range��12

8 Operation��13

9 Maintenance, repair, disposal��13

1 Preliminary note

1.1 Symbols used

►Instruction

> Reaction, result

[…] Designation of pushbuttons, buttons or indications

→Cross-reference

Information

Supplementary note�

Important note

Non-compliance can result in malfunctions or interference�

2 Safety instructions

According to the cULus approval

Caution - Use of controls or adjustments or procedures other than those

specified herein may result in hazardous radiation exposure�

Visible laser light; CLASS 1 LASER PRODUCT�

IEC 60825-1 : 2007 and IEC 60825-1 : 2014

Complies with 21 CFR 1040�10 except for deviations pursuant to Laser

Notice No� 50, dated June 2007�

Position of the product label Additional label

3 Functions and features

The diffuse reflection sensor detects objects and materials without contact and

indicates their presence by a switching signal�

4 Installation

►Align the diffuse reflection sensor to the object to be detected (Fig� 1)�

> For exact alignment, use the accessories for fine adjustment�

►Secure it to a bracket�

Fig� 1

Fig� 2 Note

The objects to be detected are to

move transversely to the lens of the

sensor�

►In case of other directions of

movement it should be tested

before whether safe switching is

guaranteed�

Fig� 3 Shiny object

►In case of shiny object surfaces

and less shiny background surfac-

es the sensor should be mounted

at an angle of appox� 5 - 10°�

Fig� 4 Shiny background

►In case of shiny background

surfaces and less shiny object

surfaces the sensor should be

mounted vertically to the back-

ground surface�

5 Operating and display elements

1: LED green - operation,

stability indication

2: OUT OFF button

3: LED yellow - switching output active

4: OUT ON button

5.1 Stability indication

The green LED is lit when the supply voltage is applied and the sensor signal is

stable�

stable signal switch point stable signal

Light-on mode

LED green on off off on

LED yellow on on off off

Dark-on mode

LED green on off off on

LED yellow off off on on

6 Electrical connection

The unit must be connected by a qualified electrician�

►The national and international regulations for the installation of electri-

cal equipment must be adhered to�

►Ensure voltage supply to EN 50178�

►Disconnect power�

►Connect the unit as follows:

6.1 PNP

Connector M12 pigtail Cable











BK: black

BN: brown

BU: blue











Colours to DIN EN 60947-5-2

Connector M8 3-pin Connector M8 4-pin





















6.2 NPN

Connector M12 pigtail Cable

L+

BK: black

BN: brown

BU: blue

L+

Colours to DIN EN 60947-5-2

Connector M8 3-pin Connector M8 4-pin

L+

7 Settings

7.1 Settings on the sensor

7.1.1 The sensor is to switch when the object is detected

Fig� 1 ►Position the object�

►Press [OUT ON] for > 2 s�

> The yellow LED flashes�

> The setting of the range with object

is made by releasing [OUT ON]�

Fig� 2 ►Remove the object

►Press [OUT OFF]�

> The setting of the range without

object is made by releasing [OUT

OFF]�

> The yellow LED goes out� Pro-

gramming is finished�

7.1.2 The sensor is not to switch when the object is detected

►Position the object (see figure 1) and press [OUT OFF] for > 2 s�

►Remove the object (see figure 2) and press [OUT ON]�

The setting can also be carried out first without object and then with object�

7.1.3 Set maximum range

►Align the sensor so that no light is reflected�

1. The sensor is to switch when the object is detected

►Press [OUT ON] for > 2 s, then [OUT OFF]�

2. The sensor is not to switch when the object is detected

►Press [OUT OFF] for > 2 s, then [OUT ON]�

7.1.4 Programming unsuccessful

> The LED flashes quickly, 8 Hz�

• Measured value difference too small

• Max� programming time (15 min�) exceeded�

7.1.5 Electronic lock

Lock or unlock the buttons

►Press [OUT ON] and [OUT OFF] simultaneously for 10 s�

> Acknowledgement is indicated by a brief change of the LED switching status�

7.2 Setting via IO-Link

This unit has an IO-Link communication interface which enables direct access

to process and diagnostic data� In addition it is possible to set the parameters of

the unit during operation� Operation of the unit via IO-Link interface requires an

IO-Link master�

With a PC, suitable IO-Link software and an IO-Link adapter cable communication

is possible when the system is not in operation�

The IODDs necessary for the configuration of the unit, detailed information about

process data structure, diagnostic information, parameter addresses and the

necessary information about the required IO-Link hardware and software can be

found at www�ifm�com�

7.2.1 Adjustable parameters

Among others, the following parameters can be set via IO-Link�

A table of all adjustable parameters can be found at www�ifm�com�

Parameter name Values Description Default

setting

SSC1 Param�

SP1

17 mm ��

100 mm

Setting of the switch point with a step in-

crement of 1 mm� After a teach the value

resulting from this teach is displayed�

Please refer to

the datasheet

value "range"

Teach SP1 TP1 Teach sequence to set switch point

SP1� Part one (TP1): teach on object�

Both parts of the teach sequence, TP1

and TP2, have to be executed, in order

to place switch point SP1 between the

object and the background

(TP = teach point)�

N� A�

Teach SP1 TP2 Teach sequence to set switch point SP1�

Part two (TP2): teach on background�

Both parts of the teach sequence, TP1

and TP2, have to be executed

(TP = teach point)�

N� A�

Teach Custom

SP1 without

target

Teach on background only, the switch

point will be defined slightly in front of

the background� Choose this setting as

an alternative to Teach SP1 if no target

is available�

N� A�

Parameter name Values Description Default

setting

TI Result�State - Idle

- SP1

Success

- Wait for

command

- Busy

- Error

- Custom

Teach-in state, after a successful teach

the value 'SP1 success' will be indicated�

N� A�

Sequence

modulation

- OFF

- AUTo

OFF: Anti-Crosstalk function off

AUTo: Anti-Crosstalk function on

OFF

SSC1 Config�

Logic

High active

Low active

Setpoint logic, state for target detected

(High: light-on mode / NO,

Low: dark-on mode / NC)

Please refer to

the datasheet

value "output

function"

SSC1 Switch-On

delay

0 �� 2 Switch-On Delay; increment 0�1 s 0

SSC1 Switch-Off

delay

0 �� 2 Switch-Off Delay; increment 0�1 s 0

Transmitter

configuration

- On

- Off

Configuration transmitter light On / Off On

Number of power

cycles

0 �� 65535 Number of power cycles N� A�

Operating hours 0 �� 65535 Operating hours N� A�

Otros manuales para O6H7 Series

Tabla de contenidos

Otros manuales de Accesorios de IFM

IFM

IFM SAxx04 Series Manual de usuario

IFM

IFM GF854S Manual de usuario

IFM

IFM UGT203 Manual de usuario

IFM

IFM Efector 200 O6E4 Manual de usuario

IFM

IFM SI 5000 Manual de usuario

IFM

IFM efector 200 OGS38 Series Manual de usuario

IFM

IFM Efector 200 OJ51 Series Manual de usuario

IFM

IFM PN00 A Series Manual de usuario

IFM

IFM LW2120 Manual de usuario

IFM

IFM OY4**S Series Manual de usuario

IFM

IFM Efector 100 GG712S Manual de usuario

IFM

IFM Efector 160 LR70 Manual de usuario

IFM

IFM KI0058 Manual de usuario

IFM

IFM OMH551 Manual de usuario

IFM

IFM MK59 Series Manual de usuario

IFM

IFM Efector 500 PI2652 Manual de usuario

IFM

IFM PM16 Series Manual de usuario

IFM

IFM Efector 300 SM8100 Manual de usuario

IFM

IFM PC3 Series Manual de usuario

IFM

IFM EC2061 Manual de usuario

IFM

IFM O5H5 Series Manual de usuario

IFM

IFM Efector 200 OGE08 Series Manual de usuario

IFM

IFM OID20 Series Manual de usuario

IFM

IFM LX0020 Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario