IFM Efector 200 OGH Manual de usuario

Operating instructions

Diffuse reflection sensor

with background suppression

OGH

701166 / 03 09 / 2005

Function and features

The diffuse reflection sensor detects objects and materials without contact and

indicates their presence by a switched signal.

Range (r): see type label (value referred to white paper 200mm x 200mm).

Electrical connection

The device shall be supplied from an isolating source and protected by

an overcurrent device such that the limited voltage circuit requirements in

accordance with UL 508 are met.

Isolate power, then connect the unit (see page 5 or type label).

Core colours (for sensors with cable connection): BN = brown, BU = blue, BK =

black.

Programming of the output function (light-on or dark-on) by wiring (see page 5 or

type label).

Installation

Pushbutton

LEDs red, green, yellow

Align the photocell and fasten it to a mounting bracket.

Maximum range is only possible with precise alignment.

Setting of the sensitivity with stationary objects

Activate the programming mode of the unit without object.

Press for about 2s until the red LED flashes.

The red LED goes out; the yellow and green LEDs flash alternately.

The unit is in the programming mode.

If in addition the red LED is lit, the reflection of the background is too intensive (e.g.

reflecting surface). Angle the unit in the horizontal plane until the red LED goes out.

If you continue with step 3 although the red LED is lit, programming is interrupted.

The unit then passes into the operating mode with the setting being unchanged.

Setting without object.

Press once.

The yellow and green LEDs go out for approx. 1s, then flash again alternately.

Setting with object.

Press once.

The yellow and green LEDs go out for approx. 1s, then the green LED is on.

The unit is in the operating mode.

Programming is only possible if you keep to this order (first background, then

object).

If the setting of the sensitivity is not possible (e.g. object signal and

background signal are about the same), the red LED flashes after step

3 for approx. 2s. The unit then passes into the operating mode with the

sensitivity being unchanged.

Setting of the maximum sensitivity

Go into the programming mode (step 1).

Align the unit so that no light is reflected.

Press the setting button twice (see steps 2 and 3).

Locking / Unlocking

Press for 10s

The red LED lights for a short time,

then the yellow and green LEDs flash

alternately;

after 10s the LEDs go out, the unit is

locked.

Press for 10s

After 10s the LEDs go out, locking is

cancelled.

Operation

Check the safe functioning of the diffuse reflection sensor. Display by LEDs.

LED green lights Unit is ready for operation.

LED yellow lights Output is switched.

LEDs yellow + red

Flash alternately, 2 Hz: output short-circuited.

Flash alternately, 1 Hz: internal malfunction,

(output is not switched).

Maintenance

Keep the lens of the sensor free from soiling.

For cleaning do not use any solvents or cleaning agents which could damage the

plastic lenses.

•

Wiring

DC PNP

L+

DC NPN

L+

1L+

L+

Tabla de contenidos

Otros manuales de Accesorios de IFM

IFM

IFM LK 022 Series Manual de usuario

IFM

IFM Efector 100 GG712S Manual de usuario

IFM

IFM O5E5 Series Manual de usuario

IFM

IFM UGT20 Series Manual de usuario

IFM

IFM LT80 Series Manual de usuario

IFM

IFM Efector 200 OM Manual de usuario

IFM

IFM GF854S Manual de usuario

IFM

IFM O2D51 Series Manual de usuario

IFM

IFM Efector 500 PY2068 Manual de usuario

IFM

IFM LDH100 Manual de usuario

IFM

IFM Efector 500 PF2652 Manual de usuario

IFM

IFM O5H5xA Series Manual de usuario

IFM

IFM LX Series Manual de usuario

IFM

IFM efector 200 OGP2 Series Manual de usuario

IFM

IFM Efector 200 Series Manual de usuario

IFM

IFM Efector 200 OJ51 Series Manual de usuario

IFM

IFM OGP7 Series Manual de usuario

IFM

IFM PN3 Series Manual de usuario

IFM

IFM O6E7 Series Manual de usuario

IFM

IFM MVQ101 Guía de aplicación

IFM

IFM OGH3 Series Manual de usuario

IFM

IFM JD Guía de aplicación

IFM

IFM efector200 OM Manual de usuario

IFM

IFM PI109 Series Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario

IFM efector 200 OGH Manual de usuario

Manuales populares de Accesorios de otras marcas