IFM Electronic Efectorsod PM2053 Manual de usuario

Operating instructions

Electronic pressure sensor

PM205x

706071/01 09/2011

Contents

1 Preliminary note��3

1�1 Symbols used ��3

2 Safety instructions ��3

3 Functions and features ��4

3�1 Applications ��4

4 Function��5

4�1 Processing of the measured signals��5

5 Installation��6

6 Electrical connection��7

7 Operation��8

7�1 Cleaning of the filter cover��8

8 Parameter setting ��9

8�1 Adjustable parameters��9

9 Scale drawing ��10

10 Technical data�� 11

10�1 Setting ranges ��12

1 Preliminary note

1.1 Symbols used

►Instruction

> Reaction, result

[…] Designation of buttons, switches or indications

→Cross-reference

Important note

Non-compliance can result in malfunctions or interference�

2 Safety instructions

• Read this ducument before installing the unit� Ensure that the product is suit-

able for your application without any restrictions�

• Non-adherence to the operating instructions or technical data can lead to

personal injury and/or damage to property�

• Inallapplicationscheckcomplianceoftheproductmaterials(→10Technical

data) with the media to be measured�

The Sensor shall be connected only by using any R/C (CYJV2) cord, having suit-

able ratings�

3 Functions and features

The pressure sensor detects the system pressure of machines and installations�

3.1 Applications

Type of pressure: relative pressure

Bestell-

nummer Messbereich Zulässiger

Überdruck Berstdruck

bar PSI bar PSI bar PSI

PM2053 -1��25 -15��363 100 1 450 350 5 070

PM2054 -0,5��10 -7��145 50 725 150 2 175

PM2055 -0,99��4,00 -14,4��58,0 30 435 100 1 450

PM2056 -0,13��2,50 -1,8��36,3 20 290 50 725

mbar PSI bar PSI bar PSI

PM2057 -50��1 000 -0,7��14,5 10 145 30 450

mbar inH2O bar inH2O bar inH2O

PM2058 -12,5��250 -5,0��100,4 10 4 000 30 12 000

MPa = bar ÷ 10 / kPa = bar × 100

Static and dynamic overpressures exceeding the indicated overload pres-

sure are to be avoided by taking appropriate measures�

The indicated bursting pressure must not be exceeded� Even if the burst-

ing pressure is exceeded only for a short time, the unit can be destroyed�

NOTE: Risk of injury!

4 Function

4.1 Processing of the measured signals

The unit converts the system pressure into an analogue output signal (4��20 mA)�

The measuring range can be scaled to up to 25% of the finalvalue of the measur-

ing range�

• By setting the parameter ASP you define the measured value at which the

output signal is 4 mA�

• By setting the parameter AEP you define the measured value at which the

output signal is 20 mA�

Factory setting Measuring range scaled

























 



P = system pressure, MEW = final value of the measuring range

The output signal is between 4 and 20 mA� It is also indicated:

• System pressure above the measuring range: output signal > 20 mA �

• System pressure below the measuring range: output signal between 4 and 3�2 mA�

The unit is ready for operation when delivered� Factory preset: not scaled (ASP =

0 bar; AEP = 100% of the final value of the measuring range)�

5 Installation

Ensure that no pressure is applied to the installation while mounting or

removing the sensor�

Aseptoflex adapters ensure that the

sensor can be connected to different

process connections�

(The adapters have to be ordered

separately as accessories�)

Mounting operation:

►Mount the adapter (B) to the sensor�

►Fix sensor + adapter by means of

a coupling nut, a clamp flange or

similar (A) to the process connec-

tion�

If it is not possible to slide the fixing

element (A) down over the top of the

sensor: slide it up over the bottom

of the sensor before the adapter is

mounted�





Mounting the Aseptoflex adapter

►Slightly grease the threads and

sealing areas of the sensor and

adapter with lubricating paste (1)�

The paste must be suitable and

approved for the application and

compatible with the elastomers

used�

Recommendation: Klüber paste

UH1 84-201 with USDA-H1 ap-

proval for the food industry�

►Make sure that the O-ring (C) is

correctly positioned�



►Screw the sensor into the adapter

until it is hand-tight� Do not damage

the sealing chamfers�



►Clamp sensor and adapter into a

clamping device (D)� Tighten the

clamping device only slightly so

that the adapter does not warp� The

sealing chamfers (E) must not be

damaged�

►Tighten the sensor using a spanner

until you can feel the end stop (cor-

responding to a maximum tighten-

ing torque of 25 Nm / 18 ftlb)� Note:

Do not overtighten� This can have

an adverse effect on the sealing�





NOTE: A guarantee for a long-term stable and maintenance-free fitting with no bug

traps in the hygienic sealing of the metal seal (Aseptoflex connection) is only valid

for once-only mounting�

Welding adapter

First weld the adapter, then mount the sensor� Follow the instructions included

with the adapter�

6 Electrical connection

The unit must be connected by a qualified electrician�

The national and international regulations for the installation of electrical

equipment must be adhered to�

Voltage supply to EN50178, SELV, PELV�

►Disconnect power�

►Connect the unit as follows:

2 wire connection 3 wire connection

























 

























Core colours of ifm sockets:

1 = BN (brown), 2 = WH (white), 3 = BU (blue), 4 = BK (black)

7 Operation

After power on of the supply voltage the unit is in the Run mode (= normal opera-

tion)� It carries out its measurement and evaluation functions and provides an

analogue signal proportional to the system pressure�

7.1 Cleaning of the filter cover

If viscous and residues producing

media clog the filter cover of the sen-

sor (and thus reduce the measuring

accuracy slightly), you can clean it�

►Unscrew the filter cover (B) (use a

pair of pliers with plastic-covered

jaws for this)�

►Clean the cover thoroughly�



The vent (A) should only be cleaned by skilled personnel and with utmost care�

Possible medium residues must not be compressed and pressed into the vent�

This could clog the filter system and reduce the measuring accuracy of the

sensor�

►Screw the filter cover again tightly�

The sensor is sufficiently protected against harsh ambient conditions (protection

IP 67)� The protection rating can be increased by a special accessory (order no�

E30043)�

8 Parameter setting

►Connect the sensor to a PC via IO-Link-Interface (order no� E30396)�

►Set the parameters with FDT service program ifm Container: The program is

part of order no� E30396�

The program library of the available DTM objects can be found at www�ifm�com

→Service→Download.

8.1 Adjustable parameters

ASP Analogue start point

Measured value at which 4 mA is provided�

AEP Analogue end point

Measured value at which 20 mA is provided�

Minimum distance between ASP and AEP = 25% of the span�

Min-Max memory for system pressure

•HI: displays the highest measured pressure�

•LO: displays the lowest measured pressure�

COF Calibration offset

The internal measured value (operating value of the sensor) is offset against the

real measured value�

•Setting range: -5 �� +5% of the value of the span (with scaling as factory setting

(ASP = 0 bar and AEP = final value of measuring range) in steps of 0�1% of the

value of the span�

CAr Calibration reset

Resets the calibration set by COF�

dAA Damping for the analogue output

Pressure peaks of short duration or high frequency can be filtered out�

dAA-value = response time between pressure change and change of the switch-

ing status in milliseconds (ms)�

•Setting range: 0 (= dAA is not active) / 0�1 s / 0�5 s / 2 s�

Uni Display unit

The measured values and values for ASP / AEP can be indicated in the following

units:

bar, mbar, PSI, MPa, kPa, inH2O (only PM2058), mmWS (only PM2058)�

diS Setting of the display

d1 / d2 / d3 = update of the measured value every 50ms / 200ms / 600ms� The

update interval only refers to the display�

ph = display of the measured peak value remains for a short time (peak hold)�

9 Scale drawing















 

Dimensions are in mm

1: Aseptoflex thread; 2: Aseptoflex sealing edge

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios de IFM Electronic

IFM Electronic

IFM Electronic efector 600 OWF Manual de usuario

IFM Electronic

IFM Electronic Efector 100 series Manual de usuario

IFM Electronic

IFM Electronic efector150 Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

IFM Electronic

IFM Electronic efector230 Manual de usuario

IFM Electronic

IFM Electronic efector 200 OT Manual de usuario

IFM Electronic

IFM Electronic Efector500 PF2058 Manual de usuario

IFM Electronic

IFM Electronic Ecomat200 Manual de usuario

IFM Electronic

IFM Electronic efector 300 SU9004 Manual de usuario

IFM Electronic

IFM Electronic LK7 Manual de usuario

IFM Electronic

IFM Electronic efector 500 PM2055 Manual de usuario

IFM Electronic

IFM Electronic efector 250 Manual de usuario

IFM Electronic

IFM Electronic Efectror 200 OGE2 Series Manual de usuario

IFM Electronic

IFM Electronic efector 200 O5 Manual de usuario

IFM Electronic

IFM Electronic efector 200 OJ50 Series Manual de usuario

IFM Electronic

IFM Electronic PA32xx Series Manual de usuario

IFM Electronic

IFM Electronic Efector 500 PN3 Manual de usuario

IFM Electronic

IFM Electronic Efector 200 Manual de usuario

IFM Electronic

IFM Electronic efector300 SBU3 Manual de usuario

IFM Electronic

IFM Electronic Efector 300 SA1004 Manual de usuario

IFM Electronic

IFM Electronic Efector200 OG Manual de usuario

IFM Electronic

IFM Electronic efector200 OGP3 Series Manual de usuario

IFM Electronic

IFM Electronic efector 200 OG laser Manual de usuario

IFM Electronic

IFM Electronic LR8009 Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Manual de usuario