ICP DAS USA LinPAC-5000 Manual de usuario

ICPDAS - 1 -

C-

-5

Version 1.2, 2011/01/20

ÂWhat’s In the Box?

LP-5K module microSD card Software Utility CD Screw Driver RS-232 Cable

ÂPreparing for start-up your LinPAC-5000

Power Supply: +10V ~ +30VDC (Ex: DP-665)

http://www.icpdas.com/products/Accessories/power_supply/power_list.htm

ÂView of the LinPAC-5000

1 USB Port 6 COM 1 (RS-232)(console) 11 LED Indicator

2 Ethernet Port 7 COM 2 (RS-485) 12 microSD socket

3 Ethernet Port 8 COM 3 (RS-232) 13 VGA Port

4 Microphone-In 9 Power 14 Xboard (optional)

5 Earphone-Out 10 Frame Ground 15 Operating Modes Selector

ÂConfiguring the operating mode

Make sure the rotary

switch place in the

“0” position.

Rotary switch position Modes of operation

0 Normal mode(Default)

1 Quick mode

2 OS update mode

3 Debug mode

Others Reserved

Normal mode(Default)

The normal mode is the default mode of operation. Use this mode for more tasks and

configurations. Programs also are executed in this mode.

Quick mode

The safe mode is used to skip the LinPAC-5000 boot screen form microSD/microSDHC

card, so as to speed up the booting process.

OS update mode

The mode is a way used to update OS, and the Linux OS image was just suitable for the

LP-5000 by ICP DAS. If the LP-5000 cannot be boot or run the normal mode, please

update OS image again. Please pay attention to backup important files first before

updating OS image. For more information, please refer to “LP-5000 OS update manual”.

Debug mode

The purpose of this mode is to development by ICP DAS.

Reserved

Rotary switch position 4~9 are reserved by ICP DAS.

ICPDAS - 2 -

ÂConnect the LinPAC-5000 and Windows PC

The port is located on the right-upper corner on the LinPAC-5000. It is a

standard RS-232 serial port, and it provides TxD, RxD, GND,

non-isolated.

Start HyperTerminal by clicking on ‘Start ÆPrograms ÆAccessories

ÆCommunications ÆHyper Terminal’

In the ‘COM properties’ dialog box, please set for 115200 bits per

second, 8 data bits, no parity, 1 stop bit and no flow control to set up

the communication parameters for the COM1 port, and press ‘OK’ when

done.

ICPDAS - 3 -

ICPDAS - 4 -

Turn on the power, and user should see a message appear on the

screen, and the total process is completed.

To login LinPAC-5000 by ‘getty’ command.

ID: root

Password: root

ÂConnect the LinPAC-5000 and Linux PC

Install HyperTerminal tool in Linux PC such as minicom, gtkterm, etc.

Take minicom as an example, please refer to the following steps:

Type ’minicom -s’ to configure COM1 port, and press down and select

‘Serial port setup’.( please set for 115200 bits per second, 8 data bits,

no parity, 1 stop bit and no flow control to set up the communication

parameters for the COM1 port). Finally, press ‘Exit’.

ICPDAS - 5 -

ICPDAS - 6 -

minicom in action

To login LinPAC-5000 by ’getty’ command.

ID: root

Password: root

ÂTelent to LinPAC-5000

In HyperTerminal :

>> In Linux PC :>> In Windows PC :

ICPDAS - 7 -

ÂGet & Configure IP of LinPAC-5000

The LinPAC-5000 network setting includes two ways. One is DHCP and the

other is “Assigned IP”. DHCP is the default setting after the LinPAC-5000 is

produced and this way is easy for users. However, if your network system is

without DHCP server, then users need to configure the network setting by using

“Assigned IP”.

Boot up LinPAC-5000 and telnet to LinPAC-5000 first.

Type in “vi /etc/network/interfaces” to open the network setting file.

ÂTechnical Support

ICP DAS Website: www.icpdas.com.tw

ICP DAS Service :

[email protected]

ICPDAS - 8 -

Tabla de contenidos

Otros manuales de Controladores de ICP DAS USA

ICP DAS USA

ICP DAS USA iP-8000-MRTU Manual de usuario

ICP DAS USA

ICP DAS USA WP-2000-CE7 Series Manual de usuario

ICP DAS USA

ICP DAS USA I-7188XBD-CAN Manual de usuario

ICP DAS USA

ICP DAS USA I-7188E3 Manual de usuario

ICP DAS USA

ICP DAS USA i8094A Manual de usuario

ICP DAS USA

ICP DAS USA TPD-703 Manual de usuario

ICP DAS USA

ICP DAS USA I-7188XB Series Manual de usuario

ICP DAS USA

ICP DAS USA WISE-52 Series Manual de usuario

ICP DAS USA

ICP DAS USA CAN-8224 Guía de configuración

ICP DAS USA

ICP DAS USA WISE-75 M Series Manual de usuario

ICP DAS USA

ICP DAS USA mPAC-7186EXD-CAN Manual de usuario

ICP DAS USA

ICP DAS USA WISE-52 Series Manual de usuario

ICP DAS USA

ICP DAS USA ISaGRAF I-8437-80 Manual de usuario

ICP DAS USA

ICP DAS USA ALM-04-MRTU Manual de usuario

ICP DAS USA

ICP DAS USA WinCon 8000 Instrucciones de uso

ICP DAS USA

ICP DAS USA LP-22 Series Manual de usuario

ICP DAS USA

ICP DAS USA WP-5231PM-3GWA-CE7 Manual de usuario

ICP DAS USA

ICP DAS USA TPD-280-H Manual de usuario

ICP DAS USA

ICP DAS USA CAN-8123 Manual de usuario

ICP DAS USA

ICP DAS USA WISE-52 Series Manual de usuario

ICP DAS USA

ICP DAS USA VPD Series Manual de usuario

ICP DAS USA

ICP DAS USA WinPAC-8000 Series Manual de usuario

ICP DAS USA

ICP DAS USA XP-9 88-IoT Series Manual de usuario

ICP DAS USA

ICP DAS USA WP-2641M-CE7 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario