Husqvarna Viking Rose 605 Manual de usuario

KEEPING THE WORLD SEWING

User’s Guide

605

Instruction book Rose

This houshold sewing machine is designed to comply with IEC/EN 60335-2-28 and UL1594

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic safety precautions should always be

followed, including the following:

Read all instructions before using this household sewing machine.

DANGER -To reduce the risk of electric shock:

• A sewing machine should never be left unattended when plugged in. Always unplug

this sewing machine from the electric outlet immediately after using and before

cleaning.

• Always unplug before relamping. Replace bulb with same type rated 5 Watt.

WARNING - To reduce the risk of burns, fire, electric

shock, or injury to persons:

• Do not allow to be used as a toy. Close attention is necessary when this sewing

machine is used by or near children or infirm persons.

• Use this sewing machine only for its intended use as described in this manual. Use

only attachments recommended by the manufacturer as contained in this manual.

• Never operate this sewing machine if it has a damaged cord or plug, if it is not

working properly, if it has been dropped or damaged, or dropped into water. Return

the sewing machine to the nearest authorised dealer or service center for

examination, repair, electrical or mechanical adjustment.

• Never operate the sewing machine with any air openings blocked. Keep ventilation

openings of the Sewing machine and foot controller free from the accumulation of

lint, dust, and loose cloth.

• Keep fingers away from all moving parts. Special care is required around the Sewing

machine needle.

• Always use the proper needle plate. The wrong plate can cause the needle to break.

• Do not use bent needles.

• Do not pull or push fabric while stitching. It may deflect the needle causing it to break.

• Switch the sewing machine off (“0”) when making any adjustment in the needle

area, such as threading needle, changing needle, threading bobbin, or changing

presser foot, etc.

• Always unplug the sewing machine from the electrical outlet when removing covers,

lubricating, or when making any other user servicing adjustments mentioned in the

instruction manual.

• Never drop or insert any object into any opening.

• Do not use outdoors.

• Do not operate where aerosol (spray) products are being used or where oxygen is

being administrated.

• To disconnect, turn all controls to the off (“0”) position, then remove plug from outlet.

• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

• Hold plug when rewinding into cord reel. Do not allow plug to whip when

rewinding.

SAVETHESE INSTRUCTIONS

Instruction book Rose 3

List of contents

Safety instructions 2

Machine parts 4-5

Procedures 6-16

Unpacking, Packing away 6

Connecting the foot control 7

Connecting to the power

supply 7

Accessory box, Sewing surface 8

Spool pin 9

Threading the upper thread 10

Threading for twin needles 11

Bobbin winding, Direct

winding 12

Threading lower thread 13

Thread tension, Correct and

incorrect thread tension 14

Presser foot pressure,

Presser foot lever, Changing

the presser foot 15

Changing the needle, Lowering

feed teeth 16

Functions 17-25

Infodisplay 17-19

Stitch selection 20

Embroidery functions 21

Memory 21

Programming 22-25

Mirror image 24

CLR - Deleting programs 25

Satin taper and darning

stitches 25

Embroidery template 34

Color information 35

Sewing 36-54

Buttonholes 36

Buttonhole sensor foot 37

Buttonhole knife, Sewing

buttons 38

Straight stitch 39

Embroidery 26-35

Storing, Connection, 26

Embroidery presser foot, 27

Get started 28

Embroidery Hoop 29

Sewing embroideries 30-31

Function buttons 32-33

Needle positions 39

Gathering with straight

stitches 40

Zipper 41

Reinforced straight stitches 42

Stretch stitch, Zigzag 42

Lace edging 43

Three-step zigzag 44

Sewing terry cloth 44

Mending and darning 44

Flatlock 45

Hemming 46

Bridging stitch 47

Seam and Overcast 47

Darning stitch 48

Automatic taper stitch 48

Decorative stitches 49

Quilting 50

Pictogram 51

Stitch table 52-53

Sewing hints 54

Free arm, Jeans hem,

Sewing on belt loops 54

Maintenance 55

Care of the machine 55

Changing light bulbs 55

Fault-finding 56-57

Accessories 58-64

Index 65-66

Instruction book Rose

Summary

17.

16.

15.

14.

13.

12.

18. 20.

21.

22.

23.

24.

25.

26.

27.

28.

29.

30.

31.

1. Door

2. Thread take-up lever

3. Presser foot pressure dial

4. Thread guide

5. Buttonhole sensor socket

6. Light

7. Needle bar

8. Presser foot

9. Free arm

10. Bobbin cover

11. Base plate

12. Drop feed dial

13. Needle plate

14. Presser bar and Presser foot

ankle

15. Needle clamp screw

16. Thread tension discs

17. Thread tension dial

18. Thread guide for bobbin

winding

19. Spool pin

20. Spool holders

21. Recess for additional spool pin

22. Quick-info

23. Thread cutter for bobbin

winding

24. Handwheel

25. Bobbin spindle, Bobbin stop

26. Infodisplay

27. Function selectors

28. Function selectors Embroidery

29. Stitch selectors

30. Embroidery card socket

31. Main power switch,

Connection to power supply

Machine parts

10.

11.

19.

Instruction book Rose 5

Summary

32.

33.

34.

35.

32. Handle

33. Presser foot lever

34. Thread cutter

35. Embroidery unit socket

36. Embroidery arm

37. Embroidery Hoop attachment

38. Embroidery unit socket

39. Release button

36.

37.

38.

39.

Machine parts

Instruction book Rose

1. Place the machine on the table or

cabinet, remove the packaging

and lift off the cover.

2. Remove the side parts of the

packing material, the extension

table, the foot control and finally

the protection cover.

3. The machine is delivered with an

accessory bag, a main cord and a

foot control cord.

4. Wipe the machine, particularly

around the needle and needle

plate to remove any soil before

sewing.

1. Unplug the cords from the wall

socket and the machine.

2. Wind the cords around your hand

and place the foot control cord in

the foot control storage space and

the main cord in the pocket of

the cover. There is also space

provided for the operating

manual. Remove the embroidery

card and the embroidery unit.

Replace the cover protecting the

socket on the machine.

3. Check to ensure that all

accessories are in the accessory

tray. Slide it onto the machine

behind the free arm.

4. Lower the presser foot.

5. Place the foot control, underside

toward you, on the accessory tray

at the back of the machine,

where also the extension table is

placed.

Packing away after sewing

Unpacking

Make sure the extension table is

fitted into the right part of the

accessory tray and fold the table

toward the machine. Fold down the

handle and replace the cover.

Procedures

Instruction book Rose 7

Connecting the foot

control

Among the accessories you will find

the foot control cord and the main

cord.

1. Place the foot control on its

narrow side. Fit the plug into the

socket inside the foot control

compartment.

2. Push it firmly to make sure it is

properly connected. This opera-

tion is only necessary the very

first time you are going to use the

machine.

3. To correctly turn away the cord,

place it into the slot, see picture.

Note: Before plugging in, check

to ensure that the foot control is

of "type FR2/FR4".

1. Connect the foot control cord to

the first socket on the bottom

right side of the machine.

2. Connect the main cord to the

back socket on the bottom right

side of the machine.

3. When you press the power

switch, both the machine and the

light are switched on.

Connecting to the power supply

On the underside of the machine you will find information about the power

supply (V) and the frequency (Hz). Check the power supply setting in the

machine to ensure that this agrees with the main supply before you connect

the machine.

For the USA and Canada

This Sewing Machine has a polarized plug (one blade wider than the other). To

reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only

one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does

not fit, contact a qualified electrician to install the proper outlet. Do not modify the

plug in any way.

Procedures

Instruction book Rose

Accessory box

1. Open the Accessory box by

placing your finger in the space

on the top and lift upward.

2. In the Accessory box there is a

special tray for presser feet and

bobbins plus space for other

accessories.

3. Store the presser feet and the

bobbins in the tray from the

beginning so they are always

easily accessible (refer to the

figure).

5. The extension table provides an

even larger work surface. To

attach the extension table, place

the rear, right corner to the

Accessory Tray and the front,

right hook onto the recess on the

free arm.

6. To remove it, push slightly in the

direction of the arrow at the front

right corner, then lift the hook out

of the free arm.

1. Keep the Accessory Tray on the

machine to provide a larger flat

work surface.

2. Slide the Accessory Tray to the

left when you wish to remove it

and use the free arm.

3. To facilitate sewing trouser legs

and sleeve hems use the free arm.

4. To replace the Accessory Tray,

slide it tight onto the machine.

Extended sewing surface

Procedures

Instruction book Rose 9

Spool pin

The machine has spool pins suitable

for all types of thread. The main

spool pin (a) is horizontal - the

thread reels off the stationary spool.

Place the spool so that the thread

reels counter-clockwise.

There are two spool holders on the

spool pin. With narrow thread

spools, the small holder (b) is

placed in front of the thread. If you

use large thread spools, the large

holder (c) is placed in front of the

thread.

Slide the correct size spool holder in

place so the flat side is pressed

firmly against the spool. No space

between spool holder and spool.

There is also a separate spool pin

(d) to be attached onto the machine.

The fingers on the extra spool pin fit

into the two holes to the right of the

fixed spool pin. Push downward to

snap in place.

The large spool holder (c) is placed

under the thread. This spool pin is

used when winding a bobbin from a

second spool of thread or for a

second spool when sewing with a

twin needle.

abd

Procedures

Instruction book Rose

Threading the upper thread

Switch off the

main switch.

Make sure the presser

foot is raised and the

needle is in the up

position

1. Pull the spool pin out.

Place the thread on

the spool pin and the

spool holder on the spool pin as

described. Push the spool pin

back in.

2. Bring the thread in the direction

of the arrow under the thread

guide (a) and over the thread

guide (b).

3. Bring the thread down between

the thread tension discs.

4. Continue threading by drawing

the thread from the right into the

slot on the take-up lever.

5. Thread last guide just above

needle.

6. The needle is threaded from front

to back. The white on the presser

foot ankle makes it easy to see

the eye of the needle.

Upper thread warning

If the upper thread breaks or if

thread spool runs out, the machine

stops and gives a signal. The symbol

is flashing on the display.

If thread breaks: Re-thread the

machine. The symbol goes out.

If thread spool runs out: Remove

your work and the bobbin. Re-

thread the machine. Replace the

bobbin and restart.

7. Place thread under the presser

foot and into the thread knife

where it is cut.

Procedures

Otros manuales para Rose 605

Otros manuales de Máquina de coser de Husqvarna Viking

Husqvarna Viking

Husqvarna Viking Lena Manual de usuario

Husqvarna Viking

Husqvarna Viking Scandinavia 100 Manual de usuario

Husqvarna Viking

Husqvarna Viking Viking H Class 100Q Manual de usuario

Husqvarna Viking

Husqvarna Viking Huskylock s21 Manual de usuario

Husqvarna Viking

Husqvarna Viking Mega Quilter Manual de usuario

Husqvarna Viking

Husqvarna Viking Eden Rose 250C Manual de usuario

Husqvarna Viking

Husqvarna Viking Tribute 140C Manual de usuario

Husqvarna Viking

Husqvarna Viking Tribute 140M Manual de usuario

Husqvarna Viking

Husqvarna Viking Sapphire 960Q Manual de usuario

Husqvarna Viking

Husqvarna Viking Platinum 755 Manual de usuario

Husqvarna Viking

Husqvarna Viking Designer SE Manual de usuario

Husqvarna Viking

Husqvarna Viking Scandinavia 200 Manual de usuario

Husqvarna Viking

Husqvarna Viking Lily 550 Manual de usuario

Husqvarna Viking

Husqvarna Viking Lily 535 Manual de usuario

Husqvarna Viking

Husqvarna Viking Viking E20 Manual de usuario

Husqvarna Viking

Husqvarna Viking Huskylock S25 Manual de usuario

Husqvarna Viking

Husqvarna Viking Opal 670 Manual de usuario

Husqvarna Viking

Husqvarna Viking Sapphire 930 Manual de usuario

Husqvarna Viking

Husqvarna Viking Designer Jade 35 Manual de usuario

Husqvarna Viking

Husqvarna Viking Designer Ruby Deluxe Manual de usuario

Husqvarna Viking

Husqvarna Viking Platinum 755 Manual de usuario

Husqvarna Viking

Husqvarna Viking Rose 605 Manual de usuario

Husqvarna Viking

Husqvarna Viking Designer Ruby Deluxe Manual de usuario

Husqvarna Viking

Husqvarna Viking Huskylock 901 Manual de usuario

Manuales populares de Máquina de coser de otras marcas

Riccar

Riccar RL634DE Manual de usuario

Singer

Singer 2517 Manual de usuario

Pfaff

Pfaff 3307-1 SERIES Manual de usuario

Janome

Janome Quilt Maker Pro 18 VERSA Manual de usuario

Siruba

Siruba C007JP Manual de usuario

Singer

Singer 148-5 Manual de usuario

IKEA

IKEA SY Manual de usuario

Pfaff

Pfaff 571 Manual de usuario

Singer

Singer 15-91 Manual de usuario

Brother

Brother BB370 Manual de usuario

Pegasus

Pegasus WT100 Series Manual de usuario

Reliable

Reliable 7100DB Manual de usuario

Pfaff

Pfaff 937 Manual de usuario

Singer

Singer 6038 Manual de usuario

Singer

Singer 413K Manual de usuario

Pfaff

Pfaff 1471 E1 Manual de usuario

Kenmore

Kenmore 16677 - Serger Sewing Machine Manual de usuario

HIGHLEAD

HIGHLEAD GC2008-M Manual de usuario