Husqvarna Viking Platinum 755 Manual de usuario

KEEPING THE WORLD SEWING

User’s Guide

This houshold sewing machine is designed to comply with

IEC/EN 60335-2-28 and UL1594.

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic safety precautions should always be followed,

including the following:

Read all instructions before using this household sewing machine.

DANGER - To reduce the risk of electric shock:

• A sewing machine should never be left unattended when plugged in. Always unplug

this sewing machine from the electric outlet immediately after using and before cleaning.

• Always unplug before relamping. Replace bulb with same type rated 5 Watt.

WARNING - To reduce the risk of burns, Àre,

electric shock, or injury to persons:

• Do not allow to be used as a toy. Close attention is necessary when this sewing

machine is used by or near children and inﬁrm persons.

• Use this sewing machine only for its intended use as described in this manual. Use

only attachments recommended by the manufacturer as contained in this manual.

• Never operate this sewing machine if it has a damaged cord or plug, if it is not

working properly, if it has been dropped or damaged, or dropped into water. Return

the sewing machine to the nearest authorized dealer or service center for examination,

repair, electrical or mechanical adjustment.

• Never operate the sewing machine with any air openings blocked. Keep ventilation

openings of the sewing machine and foot controller free from the accumulation of lint,

dust, and loose cloth.

• Keep ﬁngers away from all moving parts. Special care is required around the sewing

machine needle.

• Always use the proper needle plate. The wrong plate can cause the needle to break.

• Do not use bent needles.

• Do not pull or push fabric while stitching. It may deﬂect the needle causing it to

break.

• Switch the sewing machine off (“0”) when making any adjustment in the needle area,

such as threading needle, changing needle, threading bobbin, or changing presser

foot, etc.

• Always unplug sewing machine from the electrical outlet when removing covers,

lubricating, or when making any other user servicing adjustments mentioned in the

instruction manual.

• Never drop or insert any object into any opening.

• Do not use outdoors.

• Do not operate where aerosol (spray) products are being used or where oxygen is

being administrated.

• To disconnect, turn all controls to the off (“0”) position, then remove plug from outlet.

• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

SAVE THESE INSTRUCTIONS

Table of Contents

Learn your Platinum 2

Overview - Front 2

Overview - Rear 3

Accessory Tray 3

Accessories 3

Unpack your sewing machine 4

Connect to the Power Supply 4

Pack Away After Sewing 5

Accessory Tray 5

Spool Pins 6

Threading the Upper Thread 7

Needle Threader 8

Threading for Twin Needle 9

Bobbin Winding 10

Placing the Bobbin in the Machine 10

Winding from the Needle 11

Needles 12

Changing the Needle 12

Presser Feet 13

Changing the Presser Foot 14

Presser Foot Pressure 14

Presser Foot Lever 14

Thread Tension 15

Lowering the Feed Teeth 16

Functions and Infodisplay 17

The Touch Panel 18

Stitch Selection 20

Alphabet (Platinum 755) 21

Sewing Advisor (Platinum 715/735) 22

Icons on the InfoDisplay

(Platinum 715/735) 25

Icons on the InfoDisplay

(Platinum 755) 27

Programming 29

Sewing 33

Utility Sewing 35

Buttonholes 44

Button 47

Care of your Platinum 49

Trouble Shooting 52

Index 54

910 11

18 19 20 21

Learn your Platinum

Overview - Front

1Lid

2Dial to set presser foot pressure

3Thread take-up lever

4Thread tension

5Pre-tension disc

6Dial to set thread tension

7Sensor Buttonhole Foot socket

8Light

9Needle threader

10 Needle bar

11 Presser foot

12 Free arm

13 Bobbin cover

14 Base plate

15 Feed teeth up/down dial

16 Presser foot bar and presser foot ankle

17 Needle clamp screw

18 Thread tension disk for bobbin winding

19 Main spool pin

20 Spool holders

21 Bobbin winding guides

22 Auxilary spool pin

23 Bobbin winder spindle

24 Bobbin stop

25 Thread cutter for bobbin winding

26 Handwheel

27 InfoDisplay and Touch Panel

28 Power switch, connectors for power

supply and foot control

29 Ruler (inches and centimeters)

Learn your Platinum

Overview - Rear

30 Handle

31 Presser foot lifter

32 Thread cutter

33 Needle threader

Accessory Tray

34 Space for accessories

35 Space for presser feet

36 Space for bobbins

Accessories

Needles

Thread spools

Presser feet A, B, C, D, E, J.

Presser foot H (only Platinum 715/735).

Quilter’s 1/4" Piecing Foot P (only

Platinum 755).

Sensor Buttonhole Foot ( only Platinum

735/755).

37 Brush

38 Stitch plate opener

(to be attached to the brush)

39 Screwdriver

40 Seam ripper

41 Clearance plate

42 Bobbins

43 Felt pad

44 Light bulb remover

45 Spool holders

312

Learn your Platinum

Unpack your sewing machine

1Place the machine on a table or cabinet,

remove the packaging and lift off the

cover.

2Remove the packing material, the foot

control and Ànally the protection cover.

3The machine is delivered with an acces-

sory bag and a main cord.

4Wipe off the machine, particularly

around the needle and needle plate to

remove any soil before sewing.

Connect to the Power Supply

Among the accessories you will Ànd

the main cord. On the underside of the

machine you will Ànd information about

the power supply (V) and the frequency

(Hz).

Before plugging in the foot control, check to ensure

that it is of type “FR4” (see underside of foot

control).

1Take out the cord from the foot con-

trol. Connect the foot control cord to

the front socket on the bottom right

side of the machine.

2Connect the power cord to the rear

socket on the bottom right side of the

machine.

3When you press the power switch to

ON, both the machine and the light are

switched on.

For the USA and Canada

This sewing machine has a polarized plug (one

blade wider than the other). To reduce the risk

of electric shock, this plug is intended to Àt in a

polarized outlet only one way. If the plug does

not Àt fully in the outlet, reverse the plug. If it

still does not Àt, contact a qualiÀed electrician to

install the proper outlet. Do not modify the plug

in any way.

Learn your Platinum

Pack Away After Sewing

1Press the power switch to turn off the

machine.

2Unplug the cord from the wall socket

Àrst and then from the machine.

3Wind the main cord around your hand

and place the cord in the pocket of the

hard cover.

4Unplug the foot control cord from the

machine. Wind the foot control cord

around your hand and place it in the

space of the foot control.

5Check to ensure that all accessories are

in the accessory tray. Slide the tray on to

the machine around the free arm.

6Place the foot control, with the under-

side towards you, Àtting into the recess

of the accessory tray at the rear side of

the machine.

Accessory Tray

In the accessory tray there are special places

for presser feet, and bobbins plus space

for needles and other accessories. Store

the accessories in the tray so they are easily

accessible.

Remove the Accessory Tray

To use the free arm - remove the acces-

sory tray. When attached, there is a plastic

hook that keeps the accessory tray locked

to the machine. There is a button on the

left underside of the accessory tray (1) that

is used to unlock and remove it. Press the

button upwards and slide the accessory tray

to the left, passing the stop position, and

remove it.

Learn your Platinum

Spool Pins

Your sewing machine has two spool pins,

a main spool pin and an auxilary spool pin.

The spool pins are suitable for all types of

thread. Fold the spool pin out towards the

right. Place the thread spool on the spool

pin so that the thread reels clockwise. Slide

on a spool holder (see below) and then fold

the spool pin back to the horizontal position.

Auxilary spool pin

Main spool pin

Narrow thread spools

Large thread spools

Horizontal Position

When using the pin in horizontal posi-

tion and with narrow thread spools, place

the large spool holder (a) under the thread

spool. The small holder (b) is placed in

front of the thread spool.

If you use large spools, place the small

spool holder (b) under the thread spool and

the large holder (a) in front of it.

The Áat side of the spool holder shall be

pressed Àrmly against the spool. There

shall be no space between spool holder and

thread spool.

Vertical Position

To use the spool pin in its vertical position,

fold the spool pin out towards the right.

Slide on the large spool holder and place a

felt pad under the thread spool. This is to

prevent the thread from reeling off too fast.

Main Spool Pin

The main spool pin is adjustable and can be used in a horizontal position (the thread reels

off the stationary spool) or in a vertical position (the thread spool rotates). There are two

spool holders on the spool pin, one large (a) and one small (b). Depending on what thread

spool size or which spool pin position you are using, the spool holders are used differently.

Use the horizontal position for normal threads and the vertical position for large spools or

threads with special characteristics.

Learn your Platinum

Auxilary Spool Pin

The auxilary spool pin is used when winding

a bobbin from a second spool of thread or

for a second spool when sewing with a twin

needle.

When using the auxilary spool pin, place the

large spool holder and a felt pad under the

thread spool.

Threading the UpperThread

When threading the upper thread, make

sure that the presser foot is raised and the

needle is in the up position.

1Pull the spool pin out. Place the spool

on the spool pin with spool holder

(follow the instuctions on previous

page). The thread shall reel clockwise.

Push the spool pin back in.

Hold the thread near the spool using

your right hand. Use your left hand to

bring the end of the thread in the direc-

tion of the arrow on the machine.

2Bring the thread into the pre-tension

thread guide (a). Bring the thread down

between the thread tension discs (b).

3Continue threading in the direction indi-

cated by the arrows. Bring the thread

from the right when threading into the

slot on the take-up lever.

4Pull the thread into the last guide just

above the needle.

5The needle is threaded from front to

back (see needle threader for further

instructions).

6Place the thread under the presser foot

and into the thread cutter, pull it down-

wards to cut it.

Learn your Platinum

Needle Threader

The needle must be in the up position to

use the needle threader. We also

recommend lowering the presser foot.

1Pull the needle threader all the way

down, catching the thread under the

guide (a)

2Bring it forward until the metal Áanges

cover the needle. A small hook will pass

through the needle eye.

3Place the thread around the guide (a)

and under the Áanges in front of the

needle, so the thread catches into the

small hook.

4Let the needle threader gently swing

back. The hook pulls the thread

through the needle eye and forms a

loop behind the needle. Pull the thread

loop out behind the needle.

5Place the thread under the presser foot

and cut the thread.

Note: The needle threader is designed to be used

for size 70-120 needles. You cannot use the needle

threader for size 60 needles or smaller, the wing

needle, twin needle, triple needle or when the

Sensor Buttonhole Foot is connected.

When threading the needle manually make sure

that the needle is threaded from front to back.

The white presser foot ankle makes it easy to see

the eye of the needle. The bobbin cover can be

used as a magnifying glass.

Otros manuales para Platinum 755

Este manual sirve para los siguientes modelos

Otros manuales de Máquina de coser de Husqvarna Viking

Husqvarna Viking

Husqvarna Viking Scandinavia 100 Manual de usuario

Husqvarna Viking

Husqvarna Viking Rose 605 Manual de usuario

Husqvarna Viking

Husqvarna Viking Huskylock S25 Manual de usuario

Husqvarna Viking

Husqvarna Viking Sarah Manual de usuario

Husqvarna Viking

Husqvarna Viking Designer II Manual de usuario

Husqvarna Viking

Husqvarna Viking Lily 535 Manual de usuario

Husqvarna Viking

Husqvarna Viking Oscar Manual de usuario

Husqvarna Viking

Husqvarna Viking Eden Rose Manual de usuario

Husqvarna Viking

Husqvarna Viking Sapphire 870 QUILT Manual de usuario

Husqvarna Viking

Husqvarna Viking H Class E10 Manual de usuario

Husqvarna Viking

Husqvarna Viking Viking Topaz 40 Manual de usuario

Husqvarna Viking

Husqvarna Viking Huskylock s21 Manual de usuario

Husqvarna Viking

Husqvarna Viking Sapphire 875 Quilt Manual de usuario

Husqvarna Viking

Husqvarna Viking Sapphire 930 Manual de usuario

Husqvarna Viking

Husqvarna Viking Platinum 755 Manual de usuario

Husqvarna Viking

Husqvarna Viking Rose 605 Manual de usuario

Husqvarna Viking

Husqvarna Viking Emerald 122 Manual de usuario

Husqvarna Viking

Husqvarna Viking Eden Rose 250C Manual de usuario

Husqvarna Viking

Husqvarna Viking SAPPHIRE 9650Q Manual de usuario

Husqvarna Viking

Husqvarna Viking Sapphire 960Q Manual de usuario

Husqvarna Viking

Husqvarna Viking 90 Manual de usuario

Husqvarna Viking

Husqvarna Viking Huskylock 901 Manual de usuario

Husqvarna Viking

Husqvarna Viking H Class 200S Manual de usuario

Husqvarna Viking

Husqvarna Viking Lena Manual de usuario

Manuales populares de Máquina de coser de otras marcas

Riccar

Riccar RL634DE Manual de usuario

Singer

Singer 2517 Manual de usuario

Pfaff

Pfaff 3307-1 SERIES Manual de usuario

Janome

Janome Quilt Maker Pro 18 VERSA Manual de usuario

Siruba

Siruba C007JP Manual de usuario

Singer

Singer 148-5 Manual de usuario

IKEA

IKEA SY Manual de usuario

Pfaff

Pfaff 571 Manual de usuario

Singer

Singer 15-91 Manual de usuario

Brother

Brother BB370 Manual de usuario

Pegasus

Pegasus WT100 Series Manual de usuario

Reliable

Reliable 7100DB Manual de usuario

Pfaff

Pfaff 937 Manual de usuario

Singer

Singer 6038 Manual de usuario

Singer

Singer 413K Manual de usuario

Pfaff

Pfaff 1471 E1 Manual de usuario

Kenmore

Kenmore 16677 - Serger Sewing Machine Manual de usuario

HIGHLEAD

HIGHLEAD GC2008-M Manual de usuario