Huskie Tools ECO-EZO Manual de instrucciones
Operating Instruction Manual
For ECO-EZO Battery Powered
Compression Tool With Parts List
www.huskietools.com [email protected]
2
@huskietoolsinc
linkedin.com/company/huskie-tools
youtube.com/user/huskietools
facebook.com/huskietools
Connect with us!
www.huskietools.com [email protected]
3
CRIMPING TOOL (ECO-EZ)
Output: 6 Ton
Weight: 6 lbs. with Battery
Size: 20.5” L
Battery Type: Lithium Ion
Voltage: 14.4V DC
Rated Current: 3 Ah
Charge Time: 1 Hour
Dimensions: 3.5”L x 2.7”W x 5.3”H
Weight: 1.25 lbs.
Input Voltage: 120V AC
Charging Capacity: 20VA
Dimensions: 4.5”L x 3.5”W x 3”H
Weight: 1.5 lbs.
Battery Cartridge: BP-80
Battery Charger: CH-90
Carrying Case: ECO-EZCASE
CH-DCC DC Charger Cord
XPJ-JAW Crimping Jaw
RBC-38 Cutting Jaw
BATTERY CARTRIDGE (BP-80)
BATTERY CHARGER (CH-90)
STANDARD ACCESSORIES
OPTIONAL ACCESSORIES
• One Hand Operation
• Rotational Head
• Audible Bypass when Predetermined
Pressure is Achieved
• Tested Up To 75kV
• 6 Ton Output
• Compatible with All Huskie 14.4V Batteries
• Brush Protection Guards
• Built In “O” Nose Die
BATTERY POWERED
COMPRESSION TOOL
SPECIFICATIONS
www.huskietools.com [email protected]
4
DC CHARGER CORD
CH-DCC
Battery and Charger
• BP-80 Huskie Tools Lithium Ion Battery
• CH-90 Huskie Tools Tri-Chemistry Charger
• This charger can charge the BP-80 and ALL previous
Huskie Tools batteries, including the BP-70, BP-70EI
and the BP-70MH.
• 1 Battery Powered Tool
• 1 Carrying Case
• 1 CH-90 Tri-Chemistry Charger
• 2 BP-80 Lithium Ion Batteries
• 1 Carrying Strap
OPTIONAL ACCESSORIES
KIT INCLUDES
CRIMPING JAW
XPJ-JAW
CUTTING JAW
RBC-38
www.huskietools.com [email protected]
5
OPERATING INSTRUCTIONS
CHARGING THE BATTERY
1. Insert the plug end into a 120V power source. The LED (Power) indicator will be
steady green indicating the charger is now in “stand-by” mode and ready to
charge the battery. Do not plug the charger into a generator as this will likely
cause the fuse in the charger to short, and will not operate.
2. To charge a drained battery, insert the battery into the charger. The LED
indicator shows a steady amber while charging. A depleted battery will be
completely charged in approximately 50-70 minutes. The LED indicator will show
a steady green when the battery is fully charged.
3. If the LED indicator goes out or is ashing quick amber, this could be a possible
short in the battery circuit, or a problem with the charger itself. It is best to consult
the factory at 1-800-860-6170 for service if such a condition occurs.
4. For technical questions or difculty in operation, please call our customer service
department at 1-800-860-6170.
ATTACHING THE BATTERY CARTRIDGE
1. While pressing the latch, pull out the battery cartridge. To
replace the battery cartridge, push the new cartridge rmly into
place.
2. After inserting a battery cartridge, check that it is securely in
place by pulling gently. Do not press the latch when pulling the
cartridge.
TRIGGER AND RELEASE BUTTON
1. The ram advances when the trigger is pressed and stops when
the trigger is released.
2. To retract the ram, push the release button. The ram continues
to retract while the release button is pressed.
www.huskietools.com [email protected]
6
1. Select an appropriate size of die for the connector. Insert half of the dies into the jaw by pressing
the push pins. When the push pins are released, they will return to their original position and hold
the die in place. Attach the other half of the die in the same manner.
2. Place the connector between the dies press the trigger and advance the ram so that the connector
is held between the dies and insert conductor into the terminal.
3. Press the trigger until the compression is completed. A clicking sound will be heard while crimping
and will stop once the crimp is completed.
4. Press the release button to retract the ram. The ram continues to retract while the release button
is pressed. The ram stops when it reaches the lower end.
OPERATING INSTRUCTIONS
COMPRESSION
www.huskietools.com [email protected]
7
IMPORTANT OPERATING PRECAUTIONS
PRECAUTION FOR THE TOOL
1. Select appropriate dies for the connector to be compressed. Incorrect combinations result in
inferior connections of the conductors. Consult your connector manufacturer for the recommended
die/connector combinations.
2. Always point the tool AWAY from other people.
3. If the tool is stored for an extended period at a temperature of less than 25º F (-5ºC), the tool
should be allowed to return to room temperature to ensure smooth operation Use the tool only
after it has been at room temperature for 1 hour.
4. Do not drop the tool. Dropping the tool may damage the hydraulic circuit and result in the tool not
functioning correctly.
5. Keep the head and ram clean and free of debris. Solvents can be used to clean the head, but
should not be used on the plastic body. Use soap and water to clean the body.
1. Do not short circuit the contacts or expose the cartridge to water, oil or solvents.
2. Do not disassemble or attempt to repair the battery cartridge or dispose of in a re.
3. Do not drop or otherwise abuse the battery cartridge.
4. Do not leave the cartridge in locations where it will be exposed to a temperature greater than 140ºF
(60ºC) for an extended period.
5. The battery has a limited life. When the crimping capacity becomes about 1/2 that of the original
capacity, the battery should be replaced.
6. If the battery cartridge is stored without being charged, natural drainage will cause the power to be
reduced. The battery should be charged every 3 months if not in use.
PRECAUTION FOR THE BATTERY CARTRIDGE
PRECAUTION FOR THE CHARGER
1. The LED indicator lights up amber and remains lit when the unit starts charging a battery cartridge.
The indicator turns green when charging is completed.
2. This unit is for charging battery cartridges BP-80, BP-70E, BP-70EI and BP-70MH only. Do not use
the charger for any other devices.
3. Allow battery cartridges to cool before charging. Allow at least 15 minutes between charges when
charging several cartridges in succession.
4. Charge batteries at an ambient temperature of 50º-95ºF (10º-35º C). Charging time is
approximately 50-70 minutes for the BP-80, 50 minutes for the BP-70E and BP-70EI, and 70
minutes for the BP-70MH.
5. Never short circuit the output terminals.
6. Do not expose the charger to water, oil or solvents.
7. Do not disassemble, attempt to modify, drop or otherwise abuse charger.
www.huskietools.com [email protected]
9
ECO-EZ PARTS LIST
1 Housing ((L) EZ-01AG 150 Ram Spring (685) EZ-31 1
2 Housing (R) EZ-02AG 151 Cover EZ-32 1
3 Switch Knob EZ-03 1 52 M3 X 6 Screw 13S-23 2
4 Spring (187) 40U-10 153 Guide Ring EZ-33 1
5 Switch Rod EZ-04 1 54 Body Head EZ-34A 1
6 Switch Unit EZ-05 1 55 Pin (262) ND-08 1
7 Lever Support EZ-06 2 56 JG-10 Snap Ring 46-11 2
8 Release Lever EZ-07 1 57 4 X 18 Drive Pin (AW) ND-15 1
9 Spring (690) EZ-08 1 58 Roller ND-14 2
10 M4 X 12 Screw P500-28 659 Roller Head ND-12A 1
11 M4 X 20 Screw 558-01 460 Roller Pin ND-13 2
12 Strap 558-07 161 Rib EZ-35 1
13 Power Unit EZ-09 1 62 M4 Flat Washer EZ-36 10
14 S-32 O-Ring 220-05 163 M4 Lock Washer EZ-37 10
15 Oil Reservoir （41) EZ-11 1
16 S-36 O-Ring 85-51 1
17 Bush 80B-0605 R14A-19 1
18 1/8" Ball 40-20 1
19 M4 X 4 Screw (F.P.) 85-47 1
20 Cylinder Insert ＥＺ-13 2
21
P-6 Back-Up Ring (B.C.)
UC-28 2
22 PS-6 Pent Seal EZ-14 2
23 Pump Piston EZ-15 2
24 Spring (552) EZ-16 2
25 Release Valve Stem EZ-17 1
26 P-3 O-Ring 16-36 2
27 Reservoir Plug EZ-18 1
28 S-3 O-Ring 7R-17 1
29 SI-12.7 Ring R14A-23 2
30 Filter Mesh EZ-19 2
31 Suction Valve EZ-20 2
32 P-3 O-Ring (U801) EZ-21 2
33 5/32" Ball 22-21 3
34 Spring (688) EZ-22 2
35 M3 X 5 Screw UC-37A 1
36 Spring (689) EZ-23 1
37
P-3 Back-Up Ring (B.C.)
9H-38 1
38 Release Plug EZ-24 1
39 Valve Cartridge EZ-25 1
41 P-5 O-Ring 5N-35 1
42 3/16" Ball 16-49 2
43 Spring (686) EZ-26 2
44 Valve Screw EZ-27 2
45 M3 X 4 Screw (D.P.) ND-01 2
46 Body EZ-28 1
47 P-28 O-Ring 300-21 1
48
P-28 Back-Up Ring (B.C.)
55D-03 1
49 Ram EZ-30 1
NO.
DESCRIPTION
CODE
QTY.
NO.
DESCRIPTION
CODE
QTY.
Tabla de contenidos
Otros manuales de Herramientas eléctricas de Huskie Tools
Huskie Tools
Huskie Tools HH1500 Manual de usuario
Huskie Tools
Huskie Tools SL-750 Manual de usuario
Huskie Tools
Huskie Tools SL-610 Manual de usuario
Huskie Tools
Huskie Tools SL-BND Manual de usuario
Huskie Tools
Huskie Tools REC-BCN658 Manual de usuario
Huskie Tools
Huskie Tools SL-510 Manual de usuario
Huskie Tools
Huskie Tools REC-CN658 Manual de usuario
Huskie Tools
Huskie Tools REC-6750 Manual de usuario
Huskie Tools
Huskie Tools REC-3510 Manual de instrucciones
Huskie Tools
Huskie Tools REC-6430 Manual de usuario
Huskie Tools
Huskie Tools REC-6NDSL Manual de usuario
Huskie Tools
Huskie Tools REC-3610 Manual de instrucciones
Huskie Tools
Huskie Tools PRO LINE REC-MK7510 Manual de usuario
Huskie Tools
Huskie Tools REC-3510K Manual de instrucciones
Huskie Tools
Huskie Tools EP-750A Manual de instrucciones
Huskie Tools
Huskie Tools S-40B Manual de instrucciones
Huskie Tools
Huskie Tools SL- BC610 Manual de usuario
Huskie Tools
Huskie Tools REC-5750 Manual de instrucciones
Huskie Tools
Huskie Tools REC-6510 Manual de usuario
Huskie Tools
Huskie Tools REC-585YC Manual de instrucciones
