Huskie Tools HH1500 Manual de usuario

HUSKIE

HYDRAULIC

HAMMERS

SERVICE

MANUAL

HH1500

HH2000

HH3600

HH4500

HH5800

HH8000

CONTENTS

1. Safety Information Page 3

Safety Decals

Safety Symbols

2. Operating Instructions Page 6

How the Hammer Operates

Mounting the Hammer to Carrier

Connecting Hoses

Daily Inspection before Operation

Initial Startup, Hammer Break-in

General Operation Instructions

Cold Weather Startup and Operation

Underwater Operation

Storage

Tool Replacement

3. Maintenance Page 12

Hydraulic Oil

Checking Condition of Hydraulic Oil

Fasteners

Greasing Requirements

Nitrogen (N2) Gas Pressure Adjustment

Oil Leakage Inspection

Gas Leakage Inspection

4. Disassembly and Assembly Page 18

Disassembly

Inspection of Parts

Component Wear Limits

Assembly

5. Specifications Page 26

6. Refinishing of Pistons and Cylinders Page 27

7. Troubleshooting Diagnosis Page 28

8. Warranty Guide Lines Page 29

9. Parts List and Illustrations Page 33

1. SAFETY INFORMATION

• Always read the information in this manual before operating the hammer. Failure to

do so can result in personal injury or damage to the equipment.

• Check that all safety decals attached to the hammer and carrier are legible. Replace

worn or illegible decals.

• Do not use drugs or alcoholic beverages that impair alertness or coordination while

operating the carrier or hammer. An operator taking prescription drugs must obtain

professional medical advice to determine if he/she can safely operate the carrier and

hammer.

• Work at a slow pace when learning to operate the hammer.

• Operator training must consist of a demonstration and verbal instruction.

• New operators must start in an area free of bystanders. He/she must become familiar

with all carrier controls before operating the hammer.

• Be aware of any prohibited uses in work areas. (Excessive slopes, poor or dangerous

terrain conditions and utility hazards.)

• Operate the carrier or hammer from the operator’s seat ONLY. Make sure the seat is

fastened securely before activating controls.

• Keep hands and feet on the controls at all times while the hammer is operating.

• Always operate the carrier with the outriggers firmly positioned on the surface.

• Make sure all controls (levers and pedals) are in NEUTRAL before starting the

carrier.

• NEVER leave the carrier with the engine running. ALWAYS ENGAGE THE

PARKING BRAKE.

• Make certain there are no persons within the arc determined by the movement of

stabilizers, front bucket or backhoe boom with the hammer at full extension.

• Never operate with any person near the hammer or between the hammer and the

operator.

• Replace all faulty or leaking hydraulic hoses or fittings before operation.

• Travel with the hammer in the full tuck (transport) position only.

• Never operate the hammer with the tool retaining pin removed.

• Wear safety goggles, hearing protection and hardhat while operating the hammer.

• Before leaving the operator’s seat, always lower the carrier boom or bucket arms.

• Stop the engine before attempting to make any repairs or adjustments to either the

carrier or the hammer.

• ALWAYS OBSERVE ALL SAFETY INSTRUCTIONS APPLICABLE TO

YOUR CARRIER.

SAFETY DECALS

The decals shown below are attached to the hammer when shipped from the factory.

Read and understand them before operating the hammer. Replace any decal that has

become worn, damaged or illegible. Decals can be ordered through the parts department.

DANGER

This symbol may appear on

the hammer or in the text of

this manual. It is used to alert

the operator of an action that

can place him/her or others in

a life threatening situation.

CAUTION

This symbol appears in the

text of this manual to identify

an action or condition that

can result in damage to the

hammer or other equipment.

The notice below is included in the shipping carton. It contains information relating to

operator safety. Read and understand this notice before unpacking or operating the

hammer. We suggest you retain this notice and include it in your local safety program.

CAUTION

Never operate the hammer unless the following Safety Instructions have

been read and understood.

• Projectiles from the hammer, tool, rock or other broken material may enter

the operator’s area and cause serious or fatal injury. Use personal

protection equipment.

• Projectiles from the hammer, tool, rock or other broken material may

cause serious or fatal injury to bystanders. Do not operate the hammer

when bystanders are in the area.

• In some cases, the hammer may enter the operator’s area if a bracket or

cylinder breaks. Make sure appropriate shields are used when operating

the hammer with this type of equipment.

• Shown above is a copy of a decal that must be installed on a surface of the

hammer that faces the operator and on the carrier operator’s control area.

• Never operate the hammer if these decals are missing. Decals must be

inspected periodically to ensure that all wording is legible. Decals should

be replaced if illegible.

• Decals can be obtained at no charge from your IPC Distributor or by

contacting IPC’s Customer Service Department.

2. OPERATING INSTRUCTIONS

HOW THE HAMMER OPERATES

On larger hammers the main valve is contained in the valve box, which is bolted to the

cylinder (Figure 1). During the upward stroke, the pressure in the upper chamber is

released via the main valve and through the outlet. High pressure in the lower chamber

then forces the piston upward.

As soon as the piston reaches the upper end of the stroke, the main valve directs flow to

the upper chamber causing it to become high pressure.

Since surface Ais greater than surface B, the piston is driven downward with the help of

the accumulated energy from the gas chamber, creating the impact stroke of the hammer.

At the point of impact, the main valve shifts, releasing the high pressure from the upper

chamber, enabling the upward stroke to occur again.

Figure 1. Principle of Operation

(Refer to Table 10.)

Gas

Chamber

Pressure

receiving

surface A

Piston

Pressure

receiving

surface B Lower Chamber

High pressure

Middle Chamber

Low pressure

Main Valve

Valve Box

MOUNTING THE HAMMER TO THE CARRIER

1. Skid Steer Loader

All hammers are mounted to hammer brackets, which are then mounted to an adapter

plate using two pins. The adapter plate is mounted to the quick mount of the carrier. To

remove the hammer, first disconnect the hydraulic couplers from the inlet and outlet ports

and detach the quick mount. Seal off all plugs and hoses to prevent dust, dirt and foreign

particles from entering the system.

2. Rubber-Tired Backhoes and Excavators

All hammers are mounted to hammer brackets. The hammer brackets are mounted to the

stick of the carrier using two pins and four bushings. To remove the hammer, first

disconnect the hydraulic couplers from the inlet and outlet ports. Seal the couplers and

hoses to prevent dust, dirt, and foreign particles from entering the system. Remove the

“mounting pins” to detach hammer and bracket from the carrier stick.

CONNECTING HOSES

Connect the two hydraulic hoses to the inlet and outlet ports of the carrier using shut off

valves. When connecting, make sure that the ends are clean and engaged securely.

DAILY INSPECTION BEFORE OPERATION

1. Check the carrier hydraulic oil level before operation. The hydraulic oil level must be

correct for proper operation.

2. Check the hydraulic oil for any signs of contamination or discoloration. If any signs

of contamination appear, change the oil. (Refer to Table 2.)

NOTE: Do not mix different types of hydraulic oil.

3. Inspect all hoses and fittings for leaks or damage. Check all fasteners and tighten as

required. Replace any broken fasteners.

4. The hammer must be greased daily before use. Ten shots of grease with a grease gun

is adequate. The hammer should be greased every 2-3 hours during operation. (See

Figure 2)

5. Check the temperature of the hydraulic oil. Optimum operating temperature is 120°/

200°F (49°/93°C). The unit may not function properly and seal damage may result if

the hydraulic oil temperature goes beyond the recommended range.

Figure 2. Hammer Lubrication Point

INITIAL STARTUP, HAMMER BREAK-IN

New or rebuilt hammers require 20-40 minutes of operation at half the rated speed as a

break-in period. This allows for proper lubrication of all moving parts and for all sliding

surfaces to mate properly.

GENERAL OPERATING INSTRUCTIONS

1. Never apply the tool with a side load. The tool must always be pressed firmly against,

and be perpendicular to the material to be broken. Failure to do so can cause tool or

seal failure.

2. Impact action must be stopped immediately when the object has been broken.

3. Do not pry with the tool. This may cause the tool to break or cause abnormal wear to

the tool bushings.

4. Avoid continuous impact on the same area for more than one minute. Continuous

impact may cause a rapid increase in oil temperature and improper hammer operation.

5. Break large objects from the outside edges and work inward.

6. Do not submerge the hammer in water. The hammer is not watertight, and damage

can occur if used in this manner. Consult your dealer for underwater applications

(Ref. Figure 3.)

7. Do not use the hammer to move very large or heavy broken objects. This can cause

damage to the hammer and carrier.

8. Do not use the hammer as a lifting device.

9. Do not operate the hammer when boom cylinders are at their extreme ends. This may

cause damage to the cylinders.

10. Stop operation immediately if hoses vibrate abnormally or impact energy is

dramatically reduced. Consult Section 7. “Troubleshooting Diagnosis” for additional

information.

COLD WEATHER STARTUP AND OPERATION

Note: Internal parts of the hammer will be damaged if proper warm-up procedures are

not applied in cold weather.

1. Warm the hydraulic system of the carrier before starting the hammer. Circulate the

oil in carrier system until it is warm to the touch or approximately 60°F (15°C)

2. With engine at half throttle, activate the hammer for 5 seconds and stop for 15

seconds. Repeat cycle for 2 to 3 minutes.

UNDERWATER OPERATION

Operation of hydraulic hammers under water requires proper preparation to prevent

internal damage to hammer parts and carrier hydraulic system.

1. To prepare the hammer for underwater operation you will need

an external compressed air supply.

2. Connect air supply line to front cap threaded port (remove plug

P/N 3Z01-FP0038 as shown.) Thread is 3/8-inch pipe tapered.

3. Set pressure regulator to 50 – 90 psi.

4. Maintain air supply to hammer at all times when operating

under water

5. For HH1500 through HH8000, 20 to 50 CFM is required.

PRESSURE REGULATOR

Figure 3. Air Compressor Supply

STORAGE

1. Short Term

If the hammer will not be used for periods of one week or more, the tool should be removed from

the hammer and grease must be applied to the piston bottom. The hammer should be stored

indoors standing vertically in the working position.

2. Long Term

For storage of more than 2 - 3 weeks or where condensation or corrosion is prevalent

(salt-water areas) note the following instructions. Remove and clean the tool. Flush the

front cap with clean solvent or hydraulic oil. Coat the exposed portion of the piston with

grease, apply grease to the tool and re-install. Store the hammer vertically and away

from standing moisture. To start the hammer after long-term storage, remove the tool

and inspect the exposed portion of the piston for corrosion. If corrosion is found do not

use the hammer until the defective piston has been repaired or replaced.

TOOL REPLACEMENT

Table 1. Standard Tool Weights

TOOL WEIGHTS Kg lbs.

HH1500 45 99

HH2000 74 162

HH3600 118 260

HH4500 152 334

HH5800 174 381

HH8000 214 470

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Herramientas eléctricas de Huskie Tools

Huskie Tools

Huskie Tools SL-MKC7510 Manual de usuario

Huskie Tools

Huskie Tools SL- BC610 Manual de usuario

Huskie Tools

Huskie Tools REC-MK758U Manual de usuario

Huskie Tools

Huskie Tools REC-658U Manual de instrucciones

Huskie Tools

Huskie Tools PRO LINE REC-MK7510 Manual de usuario

Huskie Tools

Huskie Tools 7M Series Manual de usuario

Huskie Tools

Huskie Tools REC-6NDSL Manual de usuario

Huskie Tools

Huskie Tools S-40B Manual de instrucciones

Huskie Tools

Huskie Tools REC-6510K Manual de usuario

Huskie Tools

Huskie Tools REC-CN658 Manual de usuario

Huskie Tools

Huskie Tools SL-BND Manual de usuario

Huskie Tools

Huskie Tools SL-610 Manual de usuario

Huskie Tools

Huskie Tools SL-750 Manual de usuario

Huskie Tools

Huskie Tools REC-5750 Manual de instrucciones

Huskie Tools

Huskie Tools EP-750HA Manual de usuario

Huskie Tools

Huskie Tools REC-6750 Manual de usuario

Huskie Tools

Huskie Tools SL-510 Manual de usuario

Huskie Tools

Huskie Tools REC-585YC Manual de instrucciones

Huskie Tools

Huskie Tools REC-5630 Manual de instrucciones

Huskie Tools

Huskie Tools IL-ND Manual de usuario

Huskie Tools

Huskie Tools REC-3610 Manual de instrucciones

Huskie Tools

Huskie Tools REC-B6NDSL Manual de usuario

Huskie Tools

Huskie Tools EP-100WC Manual de usuario

Huskie Tools

Huskie Tools REC-B658U Manual de usuario

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual