HunterDouglas PowerView Venetian Blind 18VDC Manual de usuario

PowerView® Venetian Blind 18VDC

The PowerView® M25S single shaft motor is suited to be used with Ultimate Venetian blind hardware from

HunterDouglas.

1. Delivery condition

As standard, no remote control or hub is connected to the motor. No limits are set. Motor is default set to

Venetian

blind motor type. If the motor condition is unknown, perform the following steps.

1.1. Check motor type

The motor can be programmed as a

•16mm Venetian blind

•25mm Venetian blind (default)

By reading out the LED sequence after power up, the motor type can be seen.

Venetian blind

IMPORTANT

The motor type (default set to

25mm Venetian blind

), has to be changed to

Venetian blind 16 or 25mm

type. Use the

PowerView® Programmer

software tool to change.



MANUAL

Page 1 of 22 version: 1.1

1.2. End limits reset (factory default)

This procedure will erase all limits stored in the volatile motor memory. It will not clear the Network ID and Group

assignments. Completing an End limits reset will prevent a PowerView® remote or App from operating a window covering

until it is reprogrammed.

1.1.1 Power up the motor by connecting the power cable to

the battery wand or power supply.

1.1.2 Immediately Check the motor button LED sequence

after start up.

1.1.3 The LED sequence should read:

16mm Venetian blind 25mm Venetian blind

Note

This procedure can be skipped for a fresh out of the box motor.

The motor will jog 2x when receiving any PowerView® command (e.g. Pressing the manual control button on the motor),

to conrm no limits are set.



MANUAL

Page 2 of 22 version: 1.1

1.2.1 Remove power from the motor by disconnecting the

power cable from the battery wand or power supply

and wait for 20 seconds.

1.2.2 Press and hold the manual control button on the

motor.

1.2.3 Reconnect power to the motor while press and hold

the manual control button .

The motor LED turns red/green

1.2.4 Press and hold the manual control button until the

motor jogs 1x.

MANUAL

Page 3 of 22 version: 1.1

1.3. Network reset

This procedure will erase all network data stored in the motor, including Network ID and Group assignments. It will not

clear the end limits. Completing a Network reset will prevent a PowerView® remote or App from operating the window

covering until it is reprogrammed.

2. Pairing a remote

A PowerView® remote can control up to 6 individual groups of blinds (buttons 1 to 6 at the top of the remote). The

instructions below assign a blind to group 1.

1.2.5 Release the manual control button .

The end limits have been cleared.

1.3.1 Press and hold the manual control button on the

motor for 12 seconds.

The blind will jog 1x at 6 seconds and a second time at

12 seconds

1.3.2 Release the manual control button after the

second jog. The Network ID and Group assignments

have been cleared.

The Network ID and Group assignments have

been cleared.

MANUAL

Page 4 of 22 version: 1.1

2.1 Locate the manual control button on your blind.

2.2 Press and hold the stop button for 6 seconds.

Keep pressing until the remote lights start blinking

2.3 Press the group1 button.

IMPORTANT

Watch out to perform steps 2.4 and 2.5 within 3 seconds!



2.4 Press and hold the manual control button .

MANUAL

Page 5 of 22 version: 1.1

3. Checking motor direction

3.1. Put motor in program mode

2.5 Press the open button.

The blind will jog 1x

2.6 Release the manual control button .

2.7 Press and hold the stop button for 6 seconds.

Keep pressing until the remote lights stop blinking

The remote will exit programming mode

automatically after 20 seconds.

IMPORTANT

Reversing motor direction is only possible with a fresh out of the box motor (no limits set) or when the end limits are

reset

Before any limits are programmed, the motor direction has to be checked and reversed if needed.

If the top or bottom limit is already set, and the motor direction has to be reversed, perform a

reset

before continuing.



IMPORTANT

Watch out to perform steps 3.1.1 and 3.1.2 within 3 seconds!



MANUAL

Page 6 of 22 version: 1.1

3.2. Check and conrm

3.1.1 Press and hold the manual control button .

3.1.2 Press the open button.

Make sure group1 on the remote is selected.

The blind will jog 1x

3.1.3 Release the manual control button .

The motor LED turns red to acknowledge the motor is

in program mode

3.2.1 Press the arrow down button to check motor

direction.

MANUAL

Page 7 of 22 version: 1.1

4. Setting end limits

It doesn’t matter if you start with setting the open or the close limit rst. In this description we start with the open (top)

limit.

3.2.2.AIf the blind moves upwards, Press the 

stop button.

Motor direction NOT OK!

3.2.2.BIf the blind moves downwards, Press the 

stop button and continue with step 4.1.4

Motor direction OK!

3.2.3 Press and hold the manual control button for 1

second to reverse motor direction.

The blind will jog 1x to acknowledge the direction is

reversed

3.2.4 Continue with step 4.1.4

MANUAL

Page 8 of 22 version: 1.1

4.1. Open limit (top)

4.1.1 Press and hold the manual control button .

4.1.2 Press the open button.

Make sure group1 on the remote is selected.

The blind will jog 1x

4.1.3 Release the manual control button .

The motor LED turns red to acknowledge the motor is

in program mode

4.1.4 Use the open , stop and close buttons to

move the blind about 20cm below the headrail.

MANUAL

Page 9 of 22 version: 1.1

4.1.5 Use the open button to let the blind hit the headrail.

The motor will stop moving.

The motor needs to hit the headrail!

4.1.6 Move the blind to the desired top position with the 

open , close and stop buttons.

Always approach the desired top limit moving

upwards.

4.1.7 Press and hold the stop button for 6 seconds.

DO NOT select a group on the remote!

Keep pressing until the remote lights start blinking

IMPORTANT

Watch out to perform steps 4.1.6 and 4.1.7 within 3 seconds!



4.1.8 Press and hold the manual control button .

MANUAL

Page 10 of 22 version: 1.1

Tabla de contenidos

Otros manuales de Persiana de ventana de HunterDouglas

HunterDouglas

HunterDouglas Paramount Headrail Systems Manual de lista de piezas

HunterDouglas

HunterDouglas PowerView M40T Manual de usuario

HunterDouglas

HunterDouglas Vignette Tiered Manual de usuario

HunterDouglas

HunterDouglas Alustra Woven Textures Manual de usuario

HunterDouglas

HunterDouglas PowerView EOS Plisse Manual de usuario

HunterDouglas

HunterDouglas Vignette Modern Roman Shades Manual de lista de piezas

HunterDouglas

HunterDouglas DecoFlex WireFree Telis Instrucciones de funcionamiento

HunterDouglas

HunterDouglas Luminette Privacy Sheers Manual de lista de piezas

HunterDouglas

HunterDouglas 5-151 Manual de usuario

HunterDouglas

HunterDouglas Palmetto Horizontal Shadings Manual

HunterDouglas

HunterDouglas EverWood Guía del usuario

HunterDouglas

HunterDouglas VS 100 Guide rail Guía de mantenimiento y servicio

HunterDouglas

HunterDouglas Duette Manual de lista de piezas

HunterDouglas

HunterDouglas Pirouette PowerView+ Gen 3 Automation Manual de lista de piezas

HunterDouglas

HunterDouglas Wood Blinds Manual de usuario

HunterDouglas

HunterDouglas LiteRise Manual de usuario

HunterDouglas

HunterDouglas Vignette Traditional Manual de usuario

HunterDouglas

HunterDouglas Standard Hardware System Manual de lista de piezas

HunterDouglas

HunterDouglas Designer Roller Shades Manual de lista de piezas

HunterDouglas

HunterDouglas Paramount Manual del propietario

HunterDouglas

HunterDouglas Blockout Manual de usuario

HunterDouglas

HunterDouglas PowerView Manual de lista de piezas

HunterDouglas

HunterDouglas Silhouette Nantucket PowerView Gen 3... Manual de lista de piezas

HunterDouglas

HunterDouglas Silhouette Halo Duolite Manual de lista de piezas

Manuales populares de Persiana de ventana de otras marcas

Jysk

Jysk ROGEN Manual de usuario

SOMFY

SOMFY 1241752 Manual de usuario

Rollos

Rollos S-Nanorollo V2 Guía de planificación

Teptron

Teptron Move Manual de usuario

Renson

Renson Outdoor Loggia Guía de seguridad

Project Source

Project Source CDLF2342W Manual de usuario

Domondo

Domondo PureNight Manual de instrucciones de instalación

rollease acmeda

rollease acmeda Easy Spring Air Guía de configuración

IKEA

IKEA KADRILJ Manual de usuario

Hallis Hudson

Hallis Hudson Rolls Super glide Manual de usuario

Benthin

Benthin P1614 Manual de usuario

MV LINE

MV LINE CLARA 015 Manual de instrucciones

Current

Current E-WAND Guía

weinor

weinor VertiTex ZipR Manual

Roto

Roto ZAR M R4/R7 Manual de usuario

SOMFY

SOMFY Movelite WT Series Manual de usuario

Acmeda

Acmeda RF400 Series Manual de usuario

Motura

Motura Pli_353/3 Manual de usuario